Advantech PCM-4862 Installation and operation manual

PCM-4862 Startup Manual 1
PCM-4862 486 SBC with VGA/LCD/Ethernet/SSD
PCM-4862
486 SBC with VGA/LCD/Ethernet/SSD
Startup Manual
Packing List
SpecificationsSpecifications
SpecificationsSpecifications
Specifications
Standard SBC Functions
•CPU: 80486DX/100, DX-133
•BIOS: AWARD 128 KB Flash memory
•Chipset: VIA VT82C496G
•2nd level cache: On-board 128/512 KB (optional)
•RAM memory: 4 ~ 64 MB. Two 72-pin SIMM
sockets (accept 4/8/16 or 32 MB)
•Enhanced IDE hard disk drive interface: Supports
up to two IDE hard disks. BIOS auto-detect
•Floppy disk drive interface: Supports up to two
floppy disk drives
•Multi-mode parallel port: Configured to LPT1
LPT2, LPT3 or disabled. Supports SPP/ECP/EPP
•Serial ports: One serial RS-232 port, one serial
RS-232/422/485 port. Can be configured as COM1,
COM2, COM3, COM4 or disabled individually. Two
16550 serial UARTs
•Battery: 3.6 V @ 600 mAh lithium battery for up to
10 years of data retention
•Watchdog timer: Can generate a system reset or
IRQ15. Software enabled/disabled. Time interval is
1.6 seconds
• DMA channels: 7
• Interrupt levels: 15
• Keyboard/mouse connector: 8-pin connector
supports standard PC/AT keyboard and a PS/2
mouse
• Power management: I/O peripheral devices
support power saving and doze/standby/suspend
modes. AMP 1.1 compliant
Local-bus Flat Panel/VGA Interface
•Chipset: C&T 65545
•Display memory: 512 KB DRAM (standard), 1 MB
VRAM (optional)
•Display type: Supports CRT and flat panel (EL,
LCD and gas plasma) displays. Simultaneous
display of CRT and flat panel possible
• CRT display mode: Supports resolutions up to 800
x 600 @ 8 bpp (512 K memory) and 1024 x 768 @
8 bpp (1 MB memory)
• Panel display modes: Supports resolutions up to
800 x 600 @ 256 colors (1 MB VRAM)
Packing ListPacking List
Packing ListPacking List
Packing List
Before you begin installing your card, please make
sure that the following materials have been shipped:
• 1 PCM-4862 all-in-one single board computer
• 1 startup manual
• 1 CD-ROM or disk for utilities, drivers, and manual
(in PDF format)
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
Note: For detailed information on the PCM-4862,
please refer to the enclosed CD-ROM or
disk (in PDF format).
For more information on this and other Advantech
products please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
For technical support and service for please visit our
support website at:
http://support.advantech.com
This manual is for the PCM-4862.
Part No. 2006486210 1st edition
Printed in Taiwan Sep. 1999

2PCM-4862 Startup Manual
Jumpers and ConnectorsJumpers and Connectors
Jumpers and ConnectorsJumpers and Connectors
Jumpers and Connectors
The board has a number of jumpers that allow you to
configure your system to suit your application.
The tables below lists the function of each of the
board's jumpers and connectors:
Jumpers
Label Function
J1 System clock setting
J2 System clock setting
J3 System clock setting
J4 CPU power supply
J5 CPU type select
J6 CPU power supply
J7 CPU type select
J8 CPU type select
J9 CPU type select
J10 CPU type select
J11 CPU type select
J12 CPU type select
J13 CPU type select
J14 CMOS setup
J15 ECP/EPP DMA channel
J16 ECP/EPP DMA channel
Ethernet Controller Function
• Chipset: Realtek RTL8019AS
• Type: 16-bit Ethernet, Novell NE 2000 compatible
• Connector: 10Base-T and AUI connector on board
Solid State Disk Function
• Sockets: Three 32-pin sockets for FLASH/EPROM
• FLASH type: ATMEL 29C010/29C040A (+5 V);
AMD/Intel®28F010 (+12 V)
• Size: 360 KB / 720 KB / 1.2 MB / 1.44 MB
• Utility software: Includes software to prepare files
for EPROM
• Supports M-Systems' DiskOnChip®(DOC) 2000
PC/104 Bus Expansion
• PC/104: 104-pin connector for a 16-bit bus
• Driving capacity: Six PC/104 modules
Mechanical and Environmental
•Dimension (L x W): 203 mm x 146 mm (8" x 5.75")
•Power supply voltage: +5 V (4.75 V ~ 5.25 V)
•Power requirements: +5 V A @ 2 A (typical)
•Operating temperature: 0 ~ 60° C (32 ~ 140° F)
•Weight: 0.5 kg (1.1 lbs)
Jumpers (continued)
Label Function
J17 CPU type select
J18 CPU type select
J19 CPU type select
J20 Parallel port IRQ
J21 Buzzer enable/disable
J22 Factory reserved
J23 Watchdog timer invokes IRQ15
J24 Watchdog timer invokes system
reset
J26 Ethernet CRS LED
J27 (1,2) SSD I/O address selection
J27 (3,4) SSD I/O address selection
J27 (5,6) SSD memory address selection
J27 (7,8) SSD memory address selection
J27 (9,10) SSD drive emulated
J27 (11,12) SSD drive emulated
J28 Ethernet BNC LED
J29 SSD hardware enable/disable
J30 SSD device type and selection
J31 SSD device type and selection
J32 COM2 RS-232/422/485
Connectors
Label Function
CN1 CRT display connector
CN2 Flat panel display connector
CN3 PC/104 ISA-bus expansion
CN4 Front panel connector
CN5 PC/104 ISA-bus expansion
CN6 Peripheral power connector
(-5 V, -12 V)
CN7 Ethernet 10Base-2/10Base-5 AUI
connector
CN8 Serial port COM2 (RS-232/422/485)
CN9 Keyboard and mouse connector
CN10 Ethernet 10Base-T connector
CN11 Main power connector (+5 V, +12 V)
CN12 IDE hard drive connector
CN13 Serial port COM1 (RS-232)
CN14 Fan power connector
CN15 Floppy drive connector
CN16 Parallel port connector
J25 External battery input for CMOS data
retention

PCM-4862 Startup Manual 3
Jumper Settings
J1, J2, J3: CPU clock select
25 MHz *33 MHz 40 MHz
J1 2-3 1-2 2-3
J2 2-3 2-3 1-2
J3 1-2 2-3 1-2
J4, J6: CPU power supply select
*3.3 V 3.45 V 3.6 V 5 V
J4 1-3 1-3 1-3 3-5
2-4 2-4 2-4 4-6
J6 1-2 3-4 5-6 ---
J1 ~ J13 & J17 ~ J19: CPU type select
AMD 486DX2-66 (3 V) and AMD 486DX4-100
TI 486DX-66
AMD 486DX4-120
AMD 5x86P-75
Cyrix 486DX2-66
Cyrix 486DX2-V80GP
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10

4PCM-4862 Startup Manual
Cyrix 486DX4-100
Cyrix 5x86-100
Cyrix 5x86-120
IBM 486DX4
Intel®486DX-25
Intel®486DX2-66
Intel®486DX4-100 (default)
SGS 486DX2-66
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
5
1 2 3
J9
J10
3
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10
J6
1
J13 J17 J18
J1
J2
J3
J4
J5
J7 J8 J11 J12
2
3
4
5
6
7
8
10
9
1
2
3
4
5
6
1
2
J19
1
2
3
1
3
5
1
3
5
1 2 3
J9
J10

PCM-4862 Startup Manual 5
J14: CMOS setup
*3.6 V battery on Clear CMOS
1-2 2-3
J15 & J16: ECP/EPP/DMA channel
*DMA1 DMA3
J15
J16
J20: Parallel port IRQ select
IRQ5 *IRQ7
J21: Buzzer enable/disable
Enabled Disabled
J23 & J24: Watchdog timer system reset/IRQ15
*System reset IRQ15
J23
J24
J27, J29 ~ J31: Solid state disk configuration
Number Function
J27 (1,2) SSD I/O address selection
J27 (3,4) SSD I/O address selection
J27 (5,6) SSD memory address selection
J27 (7,8) SSD memory address selection
J27 (9,10) SSD drive emulated
J27 (11,12) SSD drive emulated
J29 SSD hardware enable/disable
J30 SSD ROM device selection
J31 SSD memory type selection
J32: COM2 select
*RS-232 RS-422 RS-485
1
3
5
1
3
5
2
4
6
2
4
6
Locating Jumpers
Locating Connectors
12 2 3
J1, J2, J3
J6
J7
J5
J8
J4
J11
J10
J17
J13
J26
J18
J12
J9
J29
J28
J19
J27
J20
J14,
J15,
J16
J32J30 J31
J21,
J22,
J23,
J24
1 2 2
3
1 2
2
3
CN10
CN7
CN14 CN9 CN15 CN12CN11 CN16
CN8
CN13
CN6
CN4
CN2
CN1
CN3,5
J25

6PCM-4862 Startup Manual
Mechanical DrawingMechanical Drawing
Mechanical DrawingMechanical Drawing
Mechanical Drawing