Advantech EKI-7529MI User manual

EKI-7529MI,
EKI-7529MI/ST
8+2 100 FX Port Unmanaged
Industrial Ethernet Switch
User Manual

Copyright
The documentation and the software included with this product are copyrighted 2009 by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time without notice. No part of
this manual may be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of Advantech Co., Ltd. Information provided in this
manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements of the rights of third parties, which may
result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Part No.
Printed in China 4th Edition
October 2009
EKI-7529MI_7529MIST_Manual_ed4 ii

Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons
other than repair personnel authorized by Advantech, or which have been subject to misuse,
abuse, accident or improper installation. Advantech assumes no liability under the terms of
this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of our
customers never need to use our repair service. If an Advantech product is defective, it will be
repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service time and freight. Please
consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU speed,
Advantech products used, other hardware and software used, etc.) Note anything
abnormal and list any onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any
helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement Order
Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable
container. A product returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to your
dealer.
iii

Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions for
passing included the equipment being operated within an industrial enclosure. In order to
protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage,
we strongly recommend the use of CE-compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech’s customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, application software,
etc.)
- A complete description of the problem
- The exact wording of any error messages
EKI-7529MI_7529MIST_Manual_ed4 iv

Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not
use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and
must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may
cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's
manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -40℃(-40℉) OR ABOVE 85℃(185℉). THIS
COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.
v

EKI-7529MI_7529MIST_Manual_ed4 vi
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from damage.
1. To avoid electrical shock, always disconnect the power from your PC chassis before you
work on it. Don't touch any components on the CPU card or other cards while the PC is
on.
2. Disconnect power before making any configuration changes. The sudden rush of power
as you connect a jumper or install a card may damage sensitive electronic components.

Contents
Chapter 1 Overview...........................................2
1.1 Introduction.........................................................2
1.1.1 High-Speed Transmissions .......................2
1.1.2 Dual Power Input.......................................2
1.1.3 Flexible Mounting ......................................2
1.1.4 Advanced Protection .................................2
1.1.5 Wide Operating Temperature....................2
1.1.6 Easy Troubleshooting................................2
1.2 Features..............................................................3
1.3 Specification .......................................................4
1.4 Packing List ........................................................6
1.5 Safety Precaution ...............................................6
Chapter 2 Installation........................................8
2.1 LED Indicators....................................................8
Table 2.1: EKI-7529MI, EKI-7529MI/ST LED
Definition.......................................................................8
Table 2.2: EKI-7529MI, EKI-7529MI/ST DIP
Definition.......................................................................8
2.2 Dimensions (units: mm)......................................9
Figure 2.1: Front View of EKI-7529MI, EKI-
7529MI/ST.....................................................................9
Figure 2.2: Side View of EKI-7529MI, EKI-
7529MI/ST...................................................................10
Figure 2.3: Rear View of EKI-7529MI, EKI-
7529MI/ST...................................................................11
Figure 2.4: Top View of EKI-7529MI, EKI-7529MI/ST
.....................................................................................11
2.3 Mounting...........................................................12
2.3.1 Wall mounting..........................................12
Figure 2.5: Combine the Metal Mounting Kit.............12
2.3.2 DIN-rail Mounting.....................................13
Figure 2.6: Installation to DIN-rail Step 1...................13
Figure 2.7: Installation to DIN-rail Step 2...................14
2.4 Network Connection .........................................15
2.5 Power Connection ............................................15
Figure 2.8: Pin Assignment of the Power Connector..15
Chapter 3 Troubleshooting ............................17
Appendix A Pin Assignment & Wiring...........19
Figure A.1: RJ-45 Pin Assignment..............................19
Figure A.2: EIA/TIA-568B .........................................19
Figure A.2: EIA/TIA-568A.........................................19
vii Contents

EKI-7529MI_7529MIST_Manual_ed4 viii

1 Chapter1
Overview
Sections include:
zIntroduction
zFeatures
zSpecifications
zPacking List
zSafety Precaution
CHAPTER

Chapter 1 Overview
1.1 Introduction
Aside from 8 x 10/100Base-TX fast Ethernet ports, the EKI-7529MI, EKI-7529MI/ST
comes equipped with 2 x 100 Mbps fiber expansion ports. Also, the long MTBF (Mean
Time Between Failures) ensures that the EKI-7529MI, EKI-7529MI/ST is a cost-
effective solution and meets the high reliability requirements demanded by industrial
applications.
1.1.1 High-Speed Transmissions
The EKI-7529MI, EKI-7529MI/ST includes a switch controller that can automatically
sense transmission speeds (10/100 Mbps). The RJ-45 interface can also be auto-
detected, so MDI or MDI-X is automatically selected and a crossover cable is not
required. All Ethernet ports have memory buffers that support the store-and-forward
mechanism. This assures that data is properly transmitted.
1.1.2 Dual Power Input
EKI-7529MI, EKI-7529MI/ST redundant power input design is with power reserve
protection to prevent the switch device broken by wrong power wiring. When one of
power input is fail, P-Fail LED will turn on and send an alarm through a relay output for
notifying user.
1.1.3 Flexible Mounting
EKI-7529MI, EKI-7529MI/ST is extremely compact (79 x 152 x 105 mm) and can be
mounted on a DIN-rail or a panel, so it is suitable for any space-constrained
environment.
1.1.4 Advanced Protection
EKI-7529MI, EKI-7529MI/ST supports up to 3,000 VDC EFT protection for power line,
and also supports 4,000VDC ESD protection for Ethernet ports. With these 2 strong
protections, it can secure equipment against unregulated voltage and make systems
safer and more reliable. Further, EKI-7529MI, EKI-7529MI/ST provides currency
overload protection with a resettable fuse to ensure that the device component won’t
be damaged by overload current.
1.1.5 Wide Operating Temperature
The operating temperature of the EKI-7529MI, EKI-7529MI/ST is between -40 ~ 75 ℃.
With such a wide range, you can use the EKI-7529MI, EKI-7529MI/ST in some of the
harshest industrial environments that exist.
1.1.6 Easy Troubleshooting
LED indicators make troubleshooting quick and easy. Each 10/100 Base-TX port has 2
LEDs that display the link status, transmission speed and collision status. Also the
three power indicators P1, P2 and P-Fail help you diagnose immediately.
EKI-7529MI_7529MIST_Manual_ed4 2