Advantech MOS-1110Y-0101E User manual

MOS-1110Y-0101E Isolated 16 DI/8 DO, 1-Ch, DB37, PCIe I/F
User Manual
The MOS-1110Y-0101E is a 16-channel isolated digital input and 8-channel isolated digital output card for the PCI Express
bus.
The MOS-1110Y-0101E's isolated digital input channels are ideal for digital input in noisy environments or with floating
potentials.Each isolated digital input supports both dry contact and wet contact, designated by jumper settings, so that it
can easily interface with other devices. Moreover, MOS-1110Y-0101E also offers counter input channels.
This manual gives you inspection and installation of hardware and drivers.
MOS-1110Y-0101E
MOS-1110Y miniPCIe card
I/O Plate card
Wire cable
Startup Manual x 1
Note: If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
You should find the following items inside the shipping package:
MOS-1110Y miniPCIe card
I/O Plate card
Wire cable
Startup Manual x 1
The MOS-1110Y-0101E card harbors certain electronic components vulnerable to electrostatic discharge (ESD). ESD could
easily damage the integrated circuits and certain components if preventive measures are not carefully paid attention to.
Before removing the card from the antistatic plastic bag, you should take following precautions to ward off possible ESD
damage:
Touch the metal part of your computer chassis with your hand to discharge static electricity accumulated on your
body. Or one can also use a grounding strap.
Touch the anti-static bag to a metal part of your computer chassis before opening the bag.
Take hold of the card only by the metal bracket when removing it out of the bag.
After taking out the card, first you should:
Inspect the card for any possible signs of external damage (loose or damaged components, etc.). If the card is visibly
damaged, please notify our service department or our local sales representative immediately. Avoid installing a damaged
card into your system.
2. Initial Inspection
1. Packing List
MOS-1110Y-0101E User Manual 1

Also pay extra caution to the following aspects to ensure proper installation:
Avoid physical contact with materials that could hold static electricity such as plastic, vinyl and Styrofoam.
Whenever you handle the card, grasp it only by its edges. DO NOT TOUCH the exposed metal pins of the connector
or the electronic components.
Note!
Advantech provides WDM CAN driver that allows you to configure your hardware and store the settings in your Windows
registry. You must install the WDM CAN driver if you want to add and manage Advantech CAN cards.
3.1 Driver Installation
For MOS-1110 driver download, please visit Advantech website:
http://support.advantech.com/Support/SearchResult.aspx?keyword=MOS-1110Y-0101E&searchtabs=BIOS,Certificate,Datasheet,Driv
er,Firmware,Manual,Online%20Training,Software%20Utility,Utility,FAQ,Installation,Software%20API,Software%20API%20Manual,3D
%20Model
1. Download and double click the .exe file from the website, then the driver will begin to setup.
2. In the Control Panel, click Advantech PCI ICOM Driver then uninstall.
3. Choose "Remove" then click "Next" then start to remove all installed components.
3. Installation & Setup
Installation
Keep the anti-static bag for future use. You might need the original bag to store the card if you have to remove the
card from PC or transport it elsewhere.
MOS-1110Y-0101E User Manual 2

3.2 Hardware Installation
After the device driver installation is completed, you can now go on to install the MOS-1110Y-0101E card in any mini-PCIe
slot on your computer. Follow the steps below to install the card on your system.
1. Turn off your computer and unplug the power cord and cables. TURN OFF your computer before installing or
removing any components on the computer.
2. Remove the cover of your computer.
3. Remove the screws from the base plate and lift to remove.
4. Insert the mini-PCIe card and secure the screws.
5. Remove the screws to remove the blanking plate.
6. Insert the MOS Module through the blanking plate hole and secure the screws. Attach the MOS Module to the
mini-PCIe card with the cable.
7. Replace the cover of your computer chassis. Re-connect the cables you removed in step 2.
8. Plug in the power cord and turn on the computer.
After the MOS-1110Y-0101E card is installed, you can verify whether it is properly installed on your system through the
Device Manager:
1. Access the Device Manager through Control Panel/System/Device Manager.
2. The device name of the MOS-1110Y-0101E should be listed on the Device Manager tab.
After your card is properly installed on your system, you can now configure your device using the Advantech Navigator after
you install DAQNavi on your computer. (DAQNavi API Download Link:
http://support.advantech.com/Support/SearchResult.aspx?keyword=DAQNavi&searchtabs=BIOS,Certificate,Datasheet,Dri
ver,Firmware,Manual,Online%20Training,Software%20Utility,Utility,FAQ,Installation,Software%20API,Software%20API%2
0Manual,3D%20Model&select_tab=Software%20API)
MOS-1110Y-0101E User Manual 3

4.1 Switch and Jumper Settings
Figure 4.1: Card Connector, Jumper and Switches
And following table shows jumper setting and board ID setting of MOS-1110Y-0101E.
Table 4.1: Summary of Jumper Settings
Table 4.2: Board ID setting (SW1)
4. Signal Connections
MOS-1110Y-0101E User Manual 4

4.2 Signal connections
4.2.1 Pin Assignment
The following tables and figures show the pin assignments of CN1 connector on the bracket to the modular card.
If you see two ports or above, it will use the same pin definition of this one.
Table 4.3: MOS-1110Y-0101E Pin Definition on iDoor Bracket
Isolated Digital Input
Each of the 16 isolated digital input channels accept voltages from 0 to 30 V. Every eight input channels share one
external common. (Channels 0 ~ 7 use ECOM0. Channels 8 ~ 15 use ECOM1.) The following figure shows how to
connect an external input source to the card's isolated inputs.
Figure 4.2 Isolated DI Connection
Isolated Digital Output
If the external voltage source (5~40 V) is connected to each isolated output channel (IDO) and its isolated digital
output turns on (200 mA max./ch), the card's current will sink from the external voltage source. DB37 provides one
EGND pin for IDO connections.
The following figure shows how to connect an external output load to the card's isolated outputs.
MOS-1110Y-0101E User Manual 5

Figure 4.3 Isolated Digital Output Connection
5.1 Specifications
Isolated Digital Input
Counter
Isolated Digital Output
General
5. Appendix
MOS-1110Y-0101E User Manual 6

5.2 Block Diagram
Figure 5.1: MOS-1110Y Block Diagram
MOS-1110Y-0101E User Manual 7