Advantech MIC-3950 User manual

Modular Industrial Computer
MIC-3950
6U CompactPCITM Dual PMC Carrier
Board

Preface and Table of Contents
PartNo.2002395000 1st Edition
Printed in Taiwan October2001
Copyright Notice
This document is copyrighted, 2001. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties which may result from its
use.
Acknowledgments
IBM, OS/2 are trademarks of International Business Machines Corpo-
ration.
Intel, Pentium, are trademarks of Intel Corporation.
Windows is a registered trademark of Microsoft Corporation.
Symbios is a trademark of Symbios Logic Corporation.
Netware is a trademark of Novell, Inc.
PICMG™,CompactPCI™ andthe PICMG™,and CompactPCI™logos
are trademarks of the PCI Industrial Computers Manufacturers Group.
All other product names or trademarks are properties of their
respective owners.
CE Notification
The MIC-3950, developed by Advantech CO., LTD., has passed the CE
test for environment specification when shielded cable are used for
external wiring. We recommend the use of shielded cables.

MIC-3950 User's Manual
Product warranty
Advantech warrants to you, the original purchaser, that each of its
products will be free from defects in materials and workmanship for
one year from the date of purchase.
This warranty does not apply to any products which have been
repaired or altered by persons other than repair personnel authorized
by Advantech, or which have been subject to misuse, abuse, accident
or improper installation. Advantech assumes no liability under the
terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous
testing, most of our customers never need to use our repair service. If
an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service
time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any on-
screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your
manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows us
to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

Preface and Table of Contents
Packing List
Before installing your board, ensure that the following materials have
been received:
• OneMIC-3950 CompactPCIPMC Carrierboard
• Oneutility CD-ROM disc and user'smanual(PDF file)
• One warranty certificate
• One Startup Manual
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3950 or any other
Advantech products, please visit our support website at:
•http://www.advantech.com.tw/support
For more information about Advantech's products and sales informa-
tion, please visit:
•http://www.advantech.com

MIC-3950 User's Manual
Contents
1. General Information............................................................ 1
1.1 Introduction ................................................................................... 2
1.2 Features ....................................................................................... 2
1.3 Specifications .............................................................................. 2
1.4 Indicator and Connector ocations ............................................. 3
1.5 Safety Precautions ...................................................................... 5
2. Hardware Installation .......................................................... 7
2.1 Initial Inspection ............................................................................ 8
2.2 Card Installation .......................................................................... 9
3. in Assignments ............................................................... 13
A.1 MIC-3950 J1 connector pin assignments ................................. 14
A.2 MIC-3950 J3 connector pin assignments ................................. 15
A.3 MIC-3950 J4 Connector Pin Assignment ................................ 16
A.4 MIC-3950 J11/J21 PMC1/PMC2 - PCI Connectors
Pin Assignment ......................................................................... 17
A.5 MIC-3950 J12 PMC1-PCI Connector Pin Assignment ........... 18
A.6 MIC-3950 J14/J24 PMC1/PMC2 Rear-Panel I/O
Connectors Pin Assignment ..................................................... 19

Preface and Table of Contents
Figures
Figure 1-1: MIC-3950 indicator and connector locations ............................. 4
Figure 2-1: Intallation for MIC-3950 .............................................................. 10
Figure 2-2: MC module installation ............................................................ 11

MIC-3950 User's Manual
Tables
Table A-1: J1 connector pin assignments ................................................... 14
Table A-2: J3 connector pin assignments ................................................... 15
Table A-3: J4 Connector in Assignment .................................................... 16
Table A-4: J11/J21 MC1/ MC2 - CI Connectors in Assignment .......... 17
Table A-5: J12 MC1- CI Connector in Assignment ................................ 18
Table A-6: J14/J24 MC1/ MC2 Rear- anel I/O Connectors in
Assignment .................................................................................. 19

1
General Information
CHAPTER

2MIC-3950 User's Manual
1.1 Introduction
The MIC-3950 is a 6U CompactPCI carrier board which comp iant with
IEEE1386.1 PMC modu es.
It supports two sing e-width PMC mezzanie modu es and 32-bit PCI op-
eration.
Once connected, the modu es are accessed via front pane connections.
1.2 Features
•6U CompactPCI form factor
•32-bit/33MHz CompactPCI interface
•Support dua PMC modu es
•On-board PCI-to-PCI bridge
1.3 Specifications
Specifications
•Bus Interface : 32-bit/33 MHz Comp iance CompactPCI Specification PICMG
2.0 R3.0
CompactPCI PMC I/O Mapping Specification PICMG 2.3 R1.0
IEEE P1386.1 PMC Specification, R2.3
•PCI Bridge : TITM 2250 PCI-to-PCI Interface Bridge Chip
•Operating Temp: 0 ~ 60°C (32 ~ 140°F)
•Storage Temp: -20 ~ 80°C (-4 ~ 176°F)
•Humidity: 5 ~ 95% (non-condensing)
•Power Consump: 1 w @ 33 Mhz
•Board Size: 233.35 x 160 mm (6U size), 1-s ot (4 TE) wide

Chapter 1 General Informat on 3
1.4 Indicator and Connector Locations
Table 1-1: MIC-3950 connector and indicator descriptions
J1 Primary CompactPCI™ bu
J3, J4 Rear I/O tran ition
J11, J12 PMC-1 32-bit PCI bu
J21, J22 PMC-2 32-bit PCI BUS
J14, J24 PMC module I/O
JP2 Internal/External Arbiter
JP3,JP4 PCI Bridge mode
JP5PVIO voltage selector
JP6SVIO voltage selector

4MIC-3950 User's Manual
Figure 1-1: MIC-3950 indicator and connector locations

Chapter 1 General Informat on 5
1.5 Safety recautions
Fo ow these simp e precautions to protect yourse f from harm and the
products from damage.
1. To avoid e ectric shock, a ways disconnect the power from your PC
chassis before you work on it. Don't touch any components on the
CPU card or other cards whi e the PC is on.
2. A ways ground yourse f to remove any static charge before you touch
your SCSI card. Be particu ar y carefu not to touch the chip connec-
tors. Keep the card in its antistatic packaging when it is not insta ed in
the PC, and p ace it on a static dissipative mat when you are working
with it. Wear grounding wrist strap for continuous protection.

6MIC-3950 User's Manual

2
Hardware Installation
CHAPTER

8MIC-3950 User's Manual
2.1 Initial Inspection
We carefu y inspected the MIC-3950 mechanica y and e ectronica y
before shipping. It shou d be free of marks and scratches and in perfect
working order on receipt.
As users unpack the MIC-3950, check it for signs of shipping damage
(damaged box, scratches, dents, etc.). If it is damaged or fai s to meet
specifications, notify Advantech's service department or the oca sa es
representative immediate y. A so notify the carrier that was used to ship
the product to user's ocation from Advantech's factory or distributor.
Retain the shipping carton and packing materia for inspection by the
carrier. Advantech wi make arrangements to repair or rep ace the unit
after an inspection.
Warning: D scharge your body's stat c electr c charge by touch-
ng the back of the grounded chass s of the system
un t (metal) before handl ng the board. You should avo d
contact w th mater als that hold a stat c charge such
as plast c, v nyl and styrofoam. Touch the board only
by ts edges to avo d stat c damage to ts ntegrated
c rcu ts. Avo d touch ng the exposed c rcu t connec-
tors.

Chapter 2 Hardware Installat on 9
2.2 Card Installation
The CompactPCI connectors are firm and rigid and require carefu han-
d ing whi e p ugging and unp ugging. Improper insta ation of a card can
easi y damage the backp ane of the chassis.
The insert/eject hand e of the MIC-3950 he ps you to insta and remove
the card easi y and safe y. Fo ow the procedure be ow to insta the
MIC-3950 into a chassis:
To install a card:
1. Ho d the card vertica y. Be sure that the card is pointing in the correct
direction. For the MIC-3950, the components of the card shou d be
pointing to the right-hand side.
2. Pu out both hand es to un ock it.
Caut on: Keep your f ngers away from the h nge to prevent your
f ngers from gett ng p nched.
3. Insert the card into the chassis by s iding the upper and ower edges
of the card into the card guide.
4. Push the card into the s ot gent y by s iding the card a ong the card
guide unti the hand es meet the rectangu ar ho es of the cross rai s.
Note: If the card s correctly pos t oned and has been sl d all
the way nto the chass s, the handle should match the
rectangular holes. If not, remove the card from the
card gu de and repeat step 3 aga n. Do not try to nstall
a card by forc ng t nto the chass s.
5. Pu the upper hand e down and ife the ower hand e up to push the
card into p ace.
6. Secure the card by pushing in the red portion to ock it into p ace.
To remove a card:
1. Unscrew the two screws on the front pane .
2. Life the upper hand e up and Press the ower hand e down to re ease
the card from the backp ane.
3. S ide the card out.

10 MIC-3950 User's Manual
Figure 2-1: Intallation for MIC-3950

Chapter 2 Hardware Installat on 11
Figure 2-2: MC module installation

12 MIC-3950 User's Manual

A
in Assignments
APPENDIX