Advantech PCIE-1752 User manual

PCIE-1752
64-ch Isolated Digital Output PCI
Express Card
User Manual

PCIE-1752 User Manual ii
Copyright
The documentation and the software included with this product are copy-
righted 2012 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this man-
ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reli-
able. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of
Microsoft Corp.
All other product names or trademarks are properties of their respective
owners.
Part No. 2003E75210 1st Edition
Printed in Taiwan March 2012

iii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous test-
ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for war-
ranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

PCIE-1752 User Manual iv
CE
This product has passed the CE test for environmental specifications
when shielded cables are used for external wiring. We recommend the use
of shielded cables. This kind of cable is available from Advantech. Please
contact your local supplier for ordering information.
FCC Class A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support
where you can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's cus-
tomer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, appli-
cation software, etc.)
- A complete description of the problem
- The exact wording of any error messages

v
Packing List
Before setting up the system, check that the items listed below are
included and in good condition. If any item does not accord with the
table, please contact your dealer immediately.
• PCIE-1752 DA&C Card
• StartUp or User Manual
• Companion DVD-ROM with DAQNavi drivers included
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the
products from damage.
1. To avoid electrical shock, always disconnect the power from your
PC chassis before you work on it. Don't touch any components on
the CPU card or other cards while the PC is on.
2. Disconnect power before making any configuration changes. The
sudden rush of power as you connect a jumper or install a card may
damage sensitive electronic components.

PCIE-1752 User Manual vi

vii
Contents
Chapter 1 Introduction ..................................................... 2
1.1 Features ............................................................................. 2
1.2 Applications ..................................................................... 4
1.3 Installation Guide ............................................................. 4
Figure 1.1:Installation Flow Chart ................................. 5
1.4 Software Overview ........................................................... 6
1.5 DAQNavi Device Driver Programming Roadmap .......... 7
1.6 Accessories........................................................................ 8
Chapter 2 Installation ..................................................... 10
2.1 Unpacking ....................................................................... 10
2.2 Driver Installation ........................................................... 11
Figure 2.1:Setup Screen of Advantech Automation Soft-
ware 11
Figure 2.2:DAQNavi Installation Setup Screen .......... 12
2.3 Hardware Installation ...................................................... 13
2.4 Device Setup & Configuration ....................................... 14
Figure 2.3:The Device Setting of PCIE-1752 .............. 14
Figure 2.4:The Digital I/O Setting Page ...................... 15
Figure 2.5:The Device Testing of PCIE-1752 ............. 16
Chapter 3 Signal Connections ........................................ 18
3.1 Overview ......................................................................... 18
3.2 Switch and Jumper Settings ........................................... 18
Figure 3.1:Connector and Switch Locations ................ 18
3.2.1 Board ID (SW1) ........................................................... 19
Table 3.1:Board ID Setting (SW1) .............................. 19
3.2.2 Power On Configuration(JP1) ..................................... 20
Table 3.2:Power on configuration after hot reset (JP1) 20
3.2.3 Channel-Freeze Function (JP2) ................................... 20
Table 3.3:Channel-Freeze Function Input Mode (JP2) 20
3.3 Signal Connections.......................................................... 21
Figure 3.2: I/O Connector Pin Assignments ................ 21
3.3.1 I/O Connector Pin Definition ....................................... 22
Table 3.4:I/O Connector Signal Descriptions .............. 22
3.3.2 Isolated Digital Output ................................................. 23
Figure 3.3:Isolated Digital Output Connection ............ 23
3.3.3 Channel-Freeze Function ............................................. 23
Figure 3.4:Wiring in wet contact input mode .............. 23
Figure 3.5:Wiring in dry contact input mode .............. 24
3.4 Field Wiring Considerations .......................................... 24
Appendix A Specifications ................................................. 26
A.1 Isolated Digital Output .................................................... 26
A.2 General ............................................................................ 26

PCIE-1752 User Manual viii
Appendix B Block Diagrams ............................................. 28
Appendix C ADAM-3951 Pin Assignment ....................... 30
Figure C.1:Connect to PCL-10250 CON1 ................... 30
Figure C.2:Connect to PCL-10250 CON2 ................... 31

2
CHAPTER
1
Introduction
This chapter introduces the PCIE-1752
cards and their typical applications.
Sections include:
• Features
• Applications
• Installation Guide
• Software Overview
• Device Driver Roadmap
• Accessories

PCIE-1752 User Manual 2
Chapter 1 Introduction
Thank you for buying the Advantech PCIE-1752 which is a 64-ch
isolated digital output card. It is an advanced-performance data
acquisition card based on 32-bit PCI Express bus architecture. It features
a unique circuit design and complete functions for data acquisition and
control. The following sections of this chapter will provide further
information about features of PCIE-1752, a Quick Start for installation,
together with some brief information on software and accessories.
1.1 Features
• 64 isolated digital output channels
• High-voltage isolation on output channels (2,500 VDC)
• Wide output range (5 ~ 40 VDC)
• High-sink current for isolated output channels (500 mA max./ch)
• Output status read-back
• Keeps the output settings and values after system hot reset
• Channel-Freeze function
• Board ID
PCIE-1752 offers the following main features:
Robust Protection
The PCIE-1752 features a robust isolation protection for applications in
industrial, lab and machinery automation. The PCIE-1752 can durably
withstand a voltage up to 2,500 VDC, preventing your host system from
any incidental harms.
Wide Output Range
The PCIE-1752 also features a wide output voltage range from 5 to 40
VDC, suitable for most industrial applications with 12 VDC/24 VDC out-
put voltage. In the mean time, we are also ready to serve your special
needs for specific output voltage range. Do not hesitate to ask us about
tailoring our standard products to meet your specifications. All these mer-
its make PCIE-1752 the best choice for industrial applications.

3 Chapter 1
Board ID Setting
The PCIE-1752 has a built-in DIP switch that helps define each card’s ID
when multiple cards have been installed on the same PC chassis. The
board ID setting function is very useful when users build their system
with multiple PCIE-1752 cards. With correct Board ID settings, you can
easily identify and access each card during hardware configuration and
software programming.
Channel-Freeze Function
The PCIE-1752 provides Channel-Freeze function, which can be enabled
either in dry contact or wet contact mode (selectable by the on-board
jumper). When the Channel-Freeze function is enabled, the last status of
each digital output channel will be safely kept for emergency use. More-
over, you can enable this function through software as it is useful in soft-
ware simulation and testing program.
Reset Protection
When the system has undergone a hot reset (i.e. without turning off the
system power), the PCIE-1752 can either retain outputs values of each
channel, or return to its default configuration as open status, depending
on its on-board jumper setting. This function protects the system from
wrong operations during unexpected system resets.
Note: For detailed specifications of the
PCIE-1752, please refer to Appendix A.

PCIE-1752 User Manual 4
1.2 Applications
• Industrial ON/OFF control
• Switch status sensing
• BCD interfacing
• Digital I/O control
• Industrial and lab automation
1.3 Installation Guide
Before you install your PCIE-1752 card, please make sure you have the
following necessary components:
PCIE-1752 DA&C Card
PCIE-1752 StartUp or User Manual
Driver Software Advantech DAQNavi software (included in DVD-
ROM)
Wiring Cable PCL-10250 or PCL-101100M (optional)
Wiring Board ADAM-3951 or ADAM-39100 (optional)
Computer PC or workstation with PCI Express bus slot (running Win-
dows XP/Vista/7)
Other optional components are also available for enhanced operation:
• Advantech DAQ tools, LabView or other 3rd-party software
After you get the necessary components and maybe some accessories for
enhanced operation for your DA&C card, you can then begin the Installa-
tion procedures. Figure 1-1 on the next page provides a concise flow chart
to give users a broad picture of the software and hardware installation
procedures:

5 Chapter 1
Figure 1.1: Installation Flow Chart

PCIE-1752 User Manual 6
1.4 Software Overview
Advantech offers a rich set of DLL drivers, third-party driver support and
application software to help fully exploit the functions of your
PCIE-1752 card:
• DAQNavi software (on the companion DVD-ROM)
• LabView driver
• Advantech DAQ tools
Programming choices for DA&C cards
You may use Advantech application software such as Advantech
DAQNavi software. On the other hand, advanced users can use register-
level programming, although this is not recommended due to its laborious
and time-consuming nature.
DAQNavi Software
Advantech DAQNavi software includes device drivers and SDK which
features a complete I/O function library to help boost your application
performance. This software is included in the companion DVD-ROM at
no extra charge and comes with all Advantech DA&C cards. The Advan-
tech DAQNavi software for Windows XP/Vista/7 works seamlessly with
development tools such as Visual Studio .Net, Visual C++, Visual Basic
and Borland Delphi.
Register-level Programming
Register-level programming is available for experienced programmers
who find it necessary to write code directly at the level of the device reg-
ister. Since register-level programming requires much effort and time, we
recommend that you use the Advantech DAQNavi software instead.
However, if register-level programming is indispensable, please contact
the technical support team to request the relative information.

7 Chapter 1
1.5 DAQNavi Device Driver Programming Roadmap
This section will provide you a roadmap to demonstrate how to build an
application from scratch using Advantech DAQNavi device drivers with
your favorite development tools such as Visual Studio.Net, Visual C++,
Visual Basic and Borland Delphi. The step-by-step instructions on how to
build your own applications using each development tool will be given in
the DAQNavi SDK Manual. Moreover, a rich set of example source code
is also given for your reference.
Programming Tools
Programmers can develop application programs with their favorite devel-
opment tools:
• Visual Studio .Net
• Visual C++ and Visual Basic
• Borland Delphi
For instructions on how to begin programming works in each develop-
ment tool, Advantech offers Tutorial Chapter in the DAQNavi SDK Man-
ual for your reference. Please refer to the corresponding sections in this
chapter on the DAQNavi SDK Manual to begin your programming
efforts. You can also look at the example source code provided for each
programming tool, since they can get you very well oriented.
The DAQNavi SDK Manual can be found on the companion DVD-ROM.
Alternatively, if you have already installed the DAQNavi SDK on your
system, the DAQNavi SDK Manual can be readily accessed through the
Start button:
Start\Programs\Advantech Automation\DAQNavi\DAQNavi Manu-
als\DAQNavi SDK Manual
The example source code could be found under the corresponding instal-
lation folder such as the default installation path:
\Advantech\DAQNavi\Examples
For information about using other function groups or other development
tools, please refer to the Using DAQNavi SDK chapter in the DAQNavi
SDK Manual, or the video tutorials in the Advantech Navigator.

PCIE-1752 User Manual 8
Programming with DAQNavi Device Drivers Function Library
Advantech DAQNavi device drivers offer a rich function library that can
be utilized in various application programs. This function library consists
of numerous APIs that support many development tools, such as Visual
Studio .Net, Visual C++, Visual Basic and Borland Delphi.
According to their specific functions or services, APIs can be categorized
into several function groups:
• Analog Input Function Group
• Analog Output Function Group
• Digital Input/Output Function Group
• Counter Function Group
For the usage and parameters of each function, please refer to the Using
DAQNavi SDK chapter in the DAQNavi SDK Manual.
Troubleshooting DAQNavi Device Drivers Error
Driver functions will return a status code when they are called to perform
a certain task for the application. When a function returns a code that is
not success, it means the function has failed to perform its designated
function. To troubleshoot the device drivers error, you can check the error
code and error description within the Error Control of each function in the
DAQNavi SDK Manual.
1.6 Accessories
Advantech offers a complete set of accessory products to support the
PCIE-1752 card. These accessories include:
Wiring Cables
PCL-10250 The PCL-10250 is a 100-pin SCSI to two 50-pin SCSI
shielded cable that specially designed for PCIE-1752 card. It should be
used with ADAM-3951 wiring board.
PCL-101100M The PCL-101100M cable is a 100pin SCSI shielded
cable. It can be used with ADAM-39100 wiring board.
Wiring Boards
ADAM-3951 The ADAM-3951 is a 50-pin SCSI wiring terminal module
with LED indicators for DIN-rail mounting.
ADAM-39100 The ADAM-39100 is a 100-pin SCSI wiring terminal
module with DIN-rail mounting.

2
CHAPTER
2
Installation
This chapter provides a packaged item
checklist, proper instructions for
unpacking and step-by-step procedures
for both driver and card installation.
Sections include:
• Unpacking
• Driver Installation
• Hardware Installation
• Device Setup & Configuration

PCIE-1752 User Manual 10
Chapter 2 Installation
2.1 Unpacking
After receiving your PCIE-1752 package, please inspect its contents first.
The package should contain the following items:
• PCIE-1752 DA&C Card
• StartUp or User Manual
• Companion DVD-ROM with DAQNavi drivers included.
The PCIE-1752cards harbor certain electronic components vulnerable to
electrostatic discharge (ESD). ESD can easily damage the integrated cir-
cuits and certain components if preventive measures are ignored.
Before removing the card from the antistatic plastic bag, you should take
the following precautions to ward off possible ESD damage:
• Touch the metal part of your computer chassis with your hand to dis-
charge the static electricity accumulated on your body. Alternatively,
one can also use a grounding strap.
• Touch the anti-static bag to a metal part of your computer chassis
before opening the bag.
• Take hold of the card only by the metal bracket when removing it out of
the bag.
After taking out the card, you should first:
• Inspect the card for any possible signs of external damage (loose or
damaged components, etc.). If the card is visibly damaged, please
notify our service department or our local sales representative immedi-
ately. Do not install a damaged card into your system.
Also, pay extra caution to the following aspects during installation:
• Avoid physical contact with materials that could hold static electricity
such as plastic, vinyl and Styrofoam.
• Whenever you handle the card, grasp it only by its edges. DO NOT
TOUCH the exposed metal pins of the connector or the electronic com-
ponents. .
Note: Keep the anti-static bag for future use. You might need
the original bag to store the card if you have to remove
the card from a PC or transport it elsewhere.

11 Chapter 2
2.2 Driver Installation
We recommend you install the driver before you install the PCIE-1752
card into your system, since this will guarantee a smooth installation pro-
cess.
The Advantech DAQNavi Device Drivers Setup program for the PCIE-
1752 card is included in the companion DVD-ROM that is shipped with
your DA&C card package. Please follow the steps below to install the
driver software:
1. Insert the companion DVD-ROM into your DVD-ROM drive.
2. The Setup program will be launched automatically if you have the
autoplay function enabled on your system. When the Setup Pro-
gram is launched, you will see the following Setup Screen.
Figure 2.1: Setup Screen of Advantech Automation Software
3. Select the DAQNavi option to install.
4. Select the Individual Driver option.
Note: If the autoplay function is not enabled on your computer,
use Windows Explorer or Windows Run command to exe-
cute autorun.exe on the companion DVD-ROM.

PCIE-1752 User Manual 12
5. Select the PCIE series and the specific device then follow the
installation instructions step by step to complete your device driver
installation and setup.
6. Back and select the DAQNavi SDK to install the Advantech Navi-
gator.
Figure 2.2: DAQNavi Installation Setup Screen
For further information on driver-related issues, an online version of the
DAQNavi SDK Manual is available by accessing the following path:
Start/Programs/Advantech Automation/DAQNavi/DAQNavi Manu-
als/DAQNavi SDK Manual
Note: You can always get the latest DAQNavi device drivers
and SDK from the Advantech Support Portal:
http://support.advantech.com.tw/support/default.aspx