AEC ILLUMINAZIONE Kaos 1 Manual

MOUNTING AND MAINTENANCE
INSTRUCTION
KAOS_IM_ENG - Rev.09 of 03/05/16 Page 1 of 2
Made in Italy
Pic. 6
Pic. 4
Pic. 1
Pic. 2
Pic. 3
MOUNTING AND MAINTENANCE
Pole head and spigot mounting bracket.
To mount the luminaire, turn properly the aluminium
shutter fixed on the frame.
The pole head connection system is suitable for pole
d.60mm or d.76mm and bracket d.42mm or d.60mm:
the system allow to install bracket parallel to the
ground or with an inclination of 5°, 10°, 15°.
The luminaire must be fixed to the pole by the
stainless steel 12MA grub screw inserted in the
aluminium shutter: the grub screw must be tightened
by a set screw wrench 6mm applying a twisting
moment of 20Nm.
To avoid the grub screw loosen, we supplied a further
stainless steel 12MA nut to be clamped on the grub
screw with an adjustable wrench of 19mm and
applying a twisting moment of 20Nm.
To gain access to electrical parts, push the secure
button which is in the middle of the stainless steel
closing hook, than lift it and open the cover [Pic. 1-2].
The cover must be blocked in vertical position by the
central hinge.
To connect the luminaire to the electrical line, punch
the press cable membrane directly with the cable
[Pic. 3].
The feeding of the fitting have to be done with a
bipolar cable with nominal diameter between 7 and 13
mm.
When it is necessary, you can take away the gear
disconnecting it (A) and turning the knobs (B) [see
Pic. 4].
To reinsert the gear plate, put it in the right position
than turn the knobs till the end and reinsert the
connector.
To close the luminaire, draw the blocking spring
[Pic. 5].
The optic of the luminaire has been projected to
function without incline the fitting.
The lamp holder block can be placed in 6 different
positions in order to adapt the photometrical solid to
the road width [Pic. 6].
A
B
This product complies with EU Directive 2002/95/EC.
The crossed-out wastebasket symbol on the appliance
means that at the end of its useful lifespan, the product
must be disposed of separately from ordinary
household wastes. The user is responsible for
delivering the appliance to an appropriate collection
facility at the end of its useful lifespan. Appropriate
separate collection to permit recycling, treatment and
environmentally compatible disposal helps prevent
negative impact on the environment and human health
and promotes recycling of the materials making up the
product. For more information on available collection
facilities, contact your local waste collection service.
INFORMATION TO THE CUSTOMERS
Directive 2002/96/EC (Waste Electrical and
Electronic Equipment - WEEE):
information for users.
Lamp positions
LAMP
POS
LAMP
POS
LAMP
POS
LAMP
POS
70W SHP-E
A4
70W MHL-E
A3
100W SHP-E
B1
100W MHL-T
C4
70W SHP-T
B3
70W MHL-T
B3
100W SHP-T
C4
150W MHL-T
C4
100W SHP-E
F4
100W MHL-E
A3
150W SHP-E
D1
250W MHL-E
D1
100W SHP-T
H3
100W MHL-T
H3
150W SHP-T
C4
250W MHL-T
D4
150W SHP-E
G2
150W MHL-E
A3
250W SHP-E
D1
400W MHL-T
G4
150W SHP-T
H3
150W MHL-T
H3
250W SHP-T
E4
250W MBF
D1
80W MBF
A4
125W MBF
C4
400W SHP-T
G4
Pic. 5

MOUNTING AND MAINTENANCE
INSTRUCTION
KAOS_IM_ENG - Rev.09 of 03/05/16 Page 2 of 2
Made in Italy
In order to insure double insulation
characteristic of the feeder cable, we
would advise that you first secure the
feeder cable to the internal cable
clamp, remove approximately 25mm
of external sheathing, and 6mm of
sheathing from the internal wires.
< 25mm
67mm
ELECTRICAL LINE CONNECTION
ATTENTION
a) The luminaire can be installed close to flammable surfaces.
b) Class II luminaires must be installed in such a way that it is impossible for any exposed metal part to come in contact with electrical
components.
c) Luminaires for Metal Halide lamps must be always complete with its protective screen.
d) For luminaires with Metal Halide lamps, damaged protective shields can only be replaced with original AEC Illuminazione’s replacement
shields.
e) On luminaires for Metal Halide lamps use only UV Stop protected lamps.
f) This luminaire has been designed and manufactured following all relevant standards. The installation must be done by experienced personnel
and following the instructions.
The present instruction paper has to be kept for any future maintenance operation on the luminaire.
Non compliance with the above will automatically release AEC Illuminazione Srl from any responsibility.
Lamp type –Weight
Model
Lamp type
Weight [gr]
Plastic cover
Aluminium cover
MBF
SHP E
SHP T
MHL E
MHL T
Empty
Wired
Empty
Wired
80 W
70 W
70 W
70 W
70 W
6.500
8.000
125 W
100 W
100 W
100 W
100 W
5.500
7.000
7.000
8.500
-
150 W
150 W
150 W
150 W
7.500
9.000
250 W
150 W
150 W
-
150 W
6.500
8.500
8.000
10.000
-
250 W
250 W
250 W
250 W
9.500
11.000
-
-
400 W
-
400 W
11.000
12.500
Shape coefficient: 1,2
Wind catching area
0,10 m2
0,12 m2
0,20 m2
0,24 m2
Dimensions
Dimensions
Bracket Ø 60mm 15°
Bracket Ø 60mm 10°
Bracket Ø 60mm 5°
Bracket Ø 60mm 0°
Bracket Ø 42mm 15°
Bracket Ø 42mm 10°
Bracket Ø 42mm 5°
Bracket Ø 42mm 0°
Pole head Ø 76mm
Pole head Ø 60mm
NO Accessory (bracket 15°)
Accessory 10° (bracket 10°)
Accessory -5° (bracket 5°)
Accessory 0° (bracket 0°)
Mounting
Suggested height of installation
Power [W]
H min [m]
H max [m]
70
4
7
150
6
10
400
8
12
Max height of installation: 15m
WIRING SCHEME
70 W SHP 70 W ÷ 400 W SHP
80 W ÷ 250 W MBF 70 W ÷ 400 W MHL
A–Ballast
L–Lamp
f–Fuse (500V)
C–Capacitor
Z–Ignitor
H
DON’T USE THIS
POSITION
ATTENTION: use only the
allowed positions (0° ,-5°,-10°).
Functioning position
Suggested: α= 90°
α