AEC ILLUMINAZIONE ITALO 1 Manual

MOUNTING AND MAINTENANCE
INSTRUCTION
ITALO_IM_ENG - Rev.08 of 27/10/14 Page 1 of 4
0°
10°
ATTACHMENT
Pic. 2
M8 (5/16") screws + split washer and plain
washer Set screw wrench: 6mm (1/2")
Twisting moment: 10Nm
20°
5°
15°
M8 Grub screws
Set screw wrench: 4mm
Twisting moment: 8Nm
--------------------------------
M8 nuts
Adjustable wrench: 13mm
Twisting moment: 8Nm
Pic. 4
Pic. 5A – Post-top mounting
Fig. 5B – Arm mounting
Pic. 3A – Post-top mounting Pic. 3B – Bracket mounting
Sign reference
0°
-10°
-20°
-5°
Sign reference
-15°
Pic. 1
MOUNTING AND MAINTENANCE INSTRUCTION
Post-top or bracket mounting
ITALO 1 is equipped with an universal attachment (post-top or bracket mounting)
according to the ordered version:
- Attachment Ø33-60mm. Ø1-3/8" - 2-3/8"
- Attachment Ø60-76mm. Ø2-3/8" - 3"
Place correctly the attachment as indicated in Pic. 5A (Post-top) or in Pic. 5B
(Bracket).
Fix the attachment to the luminaire with the two M8 screws as indicated in Pic. 2.
Possible to tilt:
- Post-top mounting: 0°, +5°, +10°, +15°, +20°
- Bracket mounting: 0°, -5°, -10°, -15°, -20°
Use the proper sign as indicated in Pic. 3A and 3B.
The regulation of the luminaire can be done loosing the two screws (Pic. 2).
Fix the attachment to the post-top or to the bracket as indicated in Pic. 4.
To avoid any possible unscrewing of grub screws, two M8 nuts have to be
tightened on the grub screws as indicate in Pic. 4.

MOUNTING AND MAINTENANCE
INSTRUCTION
ITALO_IM_ENG - Rev.08 of 27/10/14 Page 2 of 4
Pic. 6
A
Electrical line connection
To gain access to the electrical line, unlock the closing hook (A – Pic. 6) and lift the upper frame up to the action of the hinge (Pic.
7) - Luminaire with cable gland: follow the directions in Pic. 8. Is not necessary tight the external sheet of the mains
cable to the cable holder of the on-load switch. However the cable holder has to be tight to maintain in position the two
cables.
- Luminaire with membrane: follow the directions in Pic. 9. Is strictly necessary tight the external sheet of the mains
cable to the cable holder of the on-load switch.
In case the luminaire is equipped with PLM device, before close the luminaire, annotate the serial number of the device.
Pic. 8 Pic. 9
Tighten the screws up to the complete
closure of the cable holder
M20 plastic cable gland
Adjustable wrench: 24mm
Twisting moment: 4.5Nm
--------------------------------
M25 plastic cable gland
Adjustable wrench: 30mm
Twisting moment: 6Nm
CABLE GLAND MEMBRANE
Pic. 7
Hinge
CLASS I
CLASS II
C
A
B
A
B
C D
D
Cable gland Membrane
A 6 ÷7 mm 6 ÷7 mm
B < 40mm (cable of 2.5mmq)
< 25mm (cable of 1.5mmq) < 25mm
C M20: 8 ÷ 12mm
M25: 10 ÷ 17mm 8 ÷ 12mm
D ≤2.5mmq ≤2.5mmq

MOUNTING AND MAINTENANCE
INSTRUCTION
ITALO_IM_ENG - Rev.08 of 27/10/14 Page 3 of 4
Luminaire closure
To close the luminaire, follow the directive from Pic. 10 to Pic. 12.
Fig. 10 Fig. 11 Fig. 12
Lift the upper frame Unlock the hinge and move down the
upper frame
Initial position
LED module extraction
1) Disconnect the LED
connector (C);
2) Loosen the screws (E);
3) Extract the LED
module.
LED module repositioning
1) Replace in the original
position the LED
module;
2) Tighten the screws (E);
3) Connect the LED
connector (C).
Gear tray extraction
1) Disconnect the mains
connector (B);
2) Disconnect the LED
connector (C);
3) Loosen the 2 screws (D);
4) Extract the gear tray.
Gear tray repositioning
1) Replace in the original
position the gear tray;
2) Tighten the 2 screws (D);
3) Connect the LED connector
(C);
4) Connect the mains
connector (B).
B
D
C
E
SPD MAINTENANCE
The protection device is equipped with system that excludes power supply at the end of life of the luminaire.
If the luminaires switches-off when the system is still fed, the activity of the protection device should be checked looking at signaling
LED.
To check this, use the appropriate tool asked to AEC Illuminazione.
LED ON _ Right functioning of the SPD LED OFF _ End of life SPD, replace the SPD

MOUNTING AND MAINTENANCE
INSTRUCTION
ITALO_IM_ENG - Rev.08 of 27/10/14 Page 4 of 4
NOTE
a) The luminaire can be installed close to flammable surfaces.
b) Class II luminaires must be installed in such a way that it is impossible for any exposed metal part to come in contact with electrical
components.
c) The device has developed in compliance with the current standards; it is necessary that the installation is done properly, according with the
instructions supplied.
d) The present instruction paper has to be kept for any future maintenance operation on the luminaire. Non compliance with the above will
automatically release AEC Illuminazione Srl from any responsibility.
Protection earth
(only in class I)
L
N
LED
modules
CN2
PSU
WIRING SCHEME
S1
PD
F1
(
o
p
tion
)
L
N
PLM WIRING SCHEME
F Fuse 250Vac 10A (provide the fuse externally if not present into the luminaire) PD Protection device
CN Connector PSU Power Supply
S On-load switch CD Control device
Protection earth
(only in class I)
CN1
LED
modules
CN2
PSU
S1
PD
F1
(
o
p
tion
)
CN1
CD
This product complies with EU Directive 2002/95/EC. The crossed-out wastebasket symbol on the appliance means that at the end of its useful
lifespan, the product must be disposed of separately from ordinary household wastes. The user is responsible for delivering the appliance to an
appropriate collection facility at the end of its useful lifespan. Appropriate separate collection to permit recycling, treatment and environmentally
compatible disposal helps prevent negative impact on the environment and human health and promotes recycling of the materials making up the
product. For more information on available collection facilities, contact your local waste collection service.
INFORMATION TO THE CUSTOMERS
Directive 2002/96/EC (Waste Electrical and Electronic Equipment - WEEE): information for users.
Side area: 0.06m2
Base area: 0.18m2
Form factor: 1.2
Max height of installation: 15m
Ta 35°C
Use Indoor / Outdoor
ITALO 1 1M 5.2kg ÷ 5.9kg
ITALO 1 2M 5.3kg ÷ 6.7kg
ITALO 1 3M 6.0kg ÷ 6.9kg
ITALO 1 4M 6.1kg ÷ 7.0kg
ITALO 1 luminaire is
classified under
“EXEMPT GROUP”
according to
photobiologycal
safety standard
IEC/EN 62471.
NO RISK
for the operators and
end users.