AEG L9WBA61BC User manual

USER
MANUAL
EN User Manual
Washer Dryer
L9WBA61BC

CONTENTS
1. SAFETY INFORMATION.............................................................................................3
2. SAFETY INSTRUCTIONS.............................................................................................6
3. INSTALLATION............................................................................................................8
4. PRODUCT DESCRIPTION.........................................................................................13
5. CONTROL PANEL..................................................................................................... 14
6. FIRST TIME START-UP.............................................................................................. 14
7. TOUCH SCREEN....................................................................................................... 16
8. WI-FI CONNECTIVITY SETUP............................................................................. 17
9. BEFORE FIRST USE................................................................................................... 20
10. PROGRAMMES........................................................................................................20
11. OPTIONS................................................................................................................. 27
12. DAILY USE - WASHING ONLY...............................................................................32
13. DAILY USE - WASHING & DRYING....................................................................... 37
14. DAILY USE - DRYING ONLY...................................................................................39
15. SETTINGS................................................................................................................ 41
16. HINTS AND TIPS..................................................................................................... 44
17. CARE AND CLEANING.......................................................................................... 46
18. TROUBLESHOOTING.............................................................................................53
19. CONSUMPTION VALUES.......................................................................................58
20. TECHNICAL DATA..................................................................................................58
21. ACCESSORIES.........................................................................................................59
www.aeg.com
2

FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler - features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1. SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent
disability.
•This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
ENGLISH 3

instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
•Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
•Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
•Do not let children play with the appliance.
•Keep all packaging away from children and dispose of
it appropriately.
•Keep detergents away from children.
•Keep children and pets away from the appliance when
the door is open.
•If the appliance has a child safety device, it should be
activated.
•Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
•Do not change the specification of this appliance.
•This appliance is intended to be used in household
and similar applications such as:
–staff kitchen areas in shops, offices and other
working environments;
–by clients in hotels, motels, bed & breakfast and
other residential type environments;
–areas for communal use in blocks of flats or in
launderettes.
•The appliance shall be installed as a freestanding
product or below the kitchen worktop if space
margins permit.
•Do not install the appliance behind a lockable door, a
sliding door or a door with a hinge on the opposite
side, that would prevent the appliance door from
being fully open.
www.aeg.com
4

•Connect the mains plug to the mains socket only at
the end of the installation process. Make sure that the
mains plug is accessible after installation.
•The ventilation opening in the base must not be
covered by a carpet, mat, or any floor covering.
•CAUTION: The appliance must not be supplied
through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on
and off by a utility.
•Ensure good air ventilation in the room where the
appliance is installed to avoid the backflow of
unwanted gases into the room from appliances
burning gas or other fuels, including open fires.
•Exhaust air must not be discharged into a flue which is
used for exhausting fumes from any appliances
burning gas or other fuels.
•The operating water pressure at the water entry point
from the outlet connection must be between 0.5 bar
(0.05 MPa) and 8 bar (0.8 MPa).
•Do not exceed the maximum load of 10 kg (refer to
the "Programme chart" chapter).
•The appliance must be connected to the water mains
using the new supplied hose sets, or other new hose
sets supplied by the Authorised Service Centre.
•Old hose sets must not be reused.
•If the mains power supply cable is damaged, it must
be replaced by the manufacturer, its Authorised
Service Centre or similarly qualified persons to avoid
an electrical hazard.
•Wipe away lint or packaging debris that has
accumulated around the appliance.
•Do not run the appliance without filters. Clean the lint
filter before or after each use.
•Items that have been soiled with substances such as
vegetable or mineral oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and wax
removers should be washed separately with an extra
ENGLISH 5

amount of detergent before being dried in the washer
dryer.
•Do not use the appliance if items have been soiled
with industrial chemicals.
•Do not dry unwashed items in the wash dryer.
•Items such as foam rubber (latex foam), shower caps,
waterproof textiles, and rubber backed articles and
clothes, or pillows fitted with foam rubber pads should
not be dried in the washer dryer.
•Fabric softeners, or similar products, should only be
used as specified by the product manufacturer’s
instructions.
•Remove all objects from items that could be a source
of fire ignition such as lighters or matches.
•Never stop the washer dryer before the end of the
drying cycle unless all items are quickly removed and
separated so that residual heat can dissipate.
•The final part of the washer dryer cycle takes place
without heat (cool down cycle) to ensure that items
reach a temperature that will not cause damage to
them.
•Do not use high pressure water sprays and/or steam
to clean the appliance.
•Clean the appliance with a moist cloth. Use only
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
•Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
2. SAFETY INSTRUCTIONS
2.1 Installation
The installation must comply
with relevant national
regulations.
• Follow the installation instructions
supplied with the appliance.
• Do not install or use the appliance
where the temperature can be less
than 5°C or higher than 35 °C.
• Always keep the appliance vertical
when it is being moved.
• To make sure the compressor works
properly, wait 6 hours after the
installation before using the
appliance.
www.aeg.com6

• Make sure that there is air circulation
between the appliance and the floor.
• Remove all the packaging and the
transit bolts.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Keep the transit bolts in a safe place.
If the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Do not install the appliance where the
appliance door cannot be fully
opened.
• Adjust the feet to have the necessary
space between the appliance and the
flooring.
• When the appliance is in its
permanent position, check if it is
levelled correctly with the aid of a
spirit level. If it is not, adjust the feet
accordingly.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Do not touch the mains cable or the
mains plug with wet hands.
2.3 Water Connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes,
pipes not used for a long time, where
repair work has been carried out or
new devices fitted (water meters,
etc.), let the water flow until it is clean
and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
2.4 Use
WARNING!
Risk of injury, electric shock,
fire, burns or damage to the
appliance.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not touch the glass door while a
programme operates. The glass can
get hot.
• Do not dry damaged (torn, frayed)
items that contain padding or fillings.
• If laundry has been washed with a
stain remover, carry out an additional
rinse cycle before starting a drying
cycle.
• Make sure that all metal objects are
removed from the laundry.
• Dry only fabrics that are suitable to
dry in the appliance. Follow the
cleaning instruction on the item label.
• Do not sit or stand on the open door
of the appliance.
• Do not dry dripping wet clothes in the
appliance.
• Do not let hot items to touch the
plastic parts of the appliance.
• Remove a detergent ball (if used)
before starting a drying programme.
• Do not use a detergent ball if setting
a non-stop programme.
2.5 Compressor
WARNING!
Risk of damage to the
appliance.
• The compressor and its system in the
washer-dryer is filled with the special
agent which is free from fluoro-
chlorohydrocarbons. This system must
stay tight. The damage of the system
can cause a leakage.
2.6 Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
ENGLISH 7

2.7 Disposal
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Remove the door catch to prevent
children or pets from becoming
trapped in the drum.
• Dispose of the appliance in
accordance with local requirements
for the disposal of Waste Electrical
and Electronic Equipment (WEEE).
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Unpacking
WARNING!
Remove all the packaging
and the transit bolts before
installing the appliance.
WARNING!
As you will put down the
appliance on the rear side,
wait about 6 hours before
you use it. This time is
necessary to enable the
compressor to work
properly.
WARNING!
Use the gloves.
1. Remove the external film. If
necessary, use a cutter.
2. Remove the cardboard top and the
polystyrene packaging materials.
3. Remove the internal film.
4. Open the door and remove the
polystyrene piece from the door seal
and all the items from the drum.
5. Carefully put the appliance down on
its rear side.
6. Put the front polystyrene packaging
element on the floor under the
appliance.
www.aeg.com
8

Make sure not to
damage the hoses.
7. Remove the polystyrene protection
from the bottom.
1
2
8. Pull up the appliance in vertical
position.
9. Remove the power supply cable and
the drain hose from the hose holders.
It is possible to see
water flowing from the
drain hose. This is due to
the testing with water of
the appliance in factory.
10. Remove the three bolts by using the
spanner supplied with the appliance.
11. Pull out the plastic spacers.
12. Put the plastic caps, that you find in
the user manual bag, in the holes.
We recommend that you
keep the packaging and the
transit bolts for any
movement of the appliance.
ENGLISH 9

3.2 Installation under a counter
630 mm
600 mm
≥ 870 mm
The appliance can be installed as
freestanding or below the kitchen counter
with correct space (see picture).
CAUTION!
Do not install the appliance
inside a sealed hollow!
Make sure that there is air
circulation throw the bottom
of the furniture.
CAUTION!
To assure free air circulation
under the appliance, do not
attach the sound barriers (if
available).
3.3 Positioning and levelling
1. Install the appliance on a flat hard
floor.
Make sure that carpets do
not stop the air circulation
below the appliance.
Make sure that the
appliance does not touch
the wall or other units.
2. Loosen or tighten the feet to adjust
the level.
WARNING!
Do not put cardboard, wood
or equivalent materials
below the appliance feet to
adjust the level.
x4
The appliance must be level and stable.
A correct adjustment of the
appliance level prevents the
vibration, noise and the
movement of the appliance
when in operation.
When the machine is
installed on a plinth or if a
washer dryer is stacked on
the washing machine, use
the accessories described in
chapter 'Accessories'. Read
carefully the instructions
supplied with the appliance
and with the accessory.
3.4 The inlet hose
1. Connect the water inlet hose to the
back of the appliance.
2. Position it toward left or right
depending on the position of the
water tap.
www.aeg.com
10

20º20º
45º45º
Make sure that the inlet hose
is not in vertical position.
3. If necessary, loose the ring nut to set
it in the correct position.
4. Connect the water inlet hose to the
cold water tap with 3/4" thread.
CAUTION!
Make sure that there are no
leaks from the couplings.
Do not use an extension
hose if the inlet hose is too
short. Contact the service
centre for the replacement
of the inlet hose.
3.5 Water-stop device
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing.
The red sector in the window «A» shows
this fault.
A
If this occurs, close the water tap and
contact the authorized service centre to
replace the hose.
3.6 Water drainage
The drain hose should be positioned at a
height of not less than 60 cm and not
more than 100 cm from the floor.
You can extend the drain
hose to maximum 400 cm.
Contact the authorized
service centre for the other
drain hose and the
extension.
It is possible to connect the drain hose in
different ways:
1. Make a U shape with the drain hose
and put it around the plastic hose
guide.
2. On the edge of a sink - Fasten the
guide to the water tap or to the wall.
Make sure that the plastic
guide cannot move when
the appliance drains.
ENGLISH 11

Make sure that the drain
hose end is not immersed in
the water. There may be a
return of dirty water into the
appliance.
3. To a stand pipe with vent-hole -
Insert the drain hose directly into a
drain pipe. Refer to the illustration.
The end of the drain hose
must always be ventilated ,
i.e. the inner diameter of the
drain pipe (min. 38 mm -
min. 1.5") must be larger
than the external diameter
of the drain hose.
4. If the end of the drain hose looks like
this (see the picture), you can push it
directly into the stand pipe.
5. Without the plastic hose guide, to
a sink spigot - Put the drain hose in
the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the drain
hose makes a loop to
prevent particles going into
the appliance from the sink.
6. Position the hose directly to a built-
in drain pipe in the room wall and
tighten it with a clamp.
www.aeg.com
12

4. PRODUCT DESCRIPTION
4.1 Appliance overview
1 32 4 11
6
7
8
9
5
12
10
13 14
1Worktop
2Detergent dispenser
3Air filter(s)
4Control panel
5Door handle
6Rating plate
7Drain pump filter
8Feet for levelling the appliance
9Airflow slots
10 Water drain hose
11 Water inlet valve
12 Mains cable
13 Transit bolts
14 Hose supports
ENGLISH 13

5. CONTROL PANEL
5.1 Control panel description
Dry
Wash
Mode
321
5
4
1On/Off button
Pressing this button for a few
seconds allows to activate or
deactivate the appliance. Two
different tunes sound while switching
the appliance on or off.
As the Stand-by function
automatically deactivates the
appliance to decrease the energy
consumption in a few cases, you may
need to activate the appliance again.
For more details, refer to "Stand-by
option" paragraph in "Daily Use"
chapter.
2Programme dial
It can be rotated clockwise or
anticlockwise to set desired
programme, options and settings.
3Touch screen
Programmes, options and settings
can also be set by scrolling and
tapping the touch screen.
4Washing and drying mode button
(Mode).
•Wash
•Dry
If both indicators are on, the
appliance performs a complete
washing and drying cycle.
5Start/Pause button
Touch the Start/Pause button to
start, pause the appliance or
interrupt a running programme.
6. FIRST TIME START-UP
Each time you turn the appliance on, the
Start-up Screen appears on the touch
screen.
AEG
13.45
The first time you turn the appliance on,
after the Start-up Screen you are guided
through the initial setup procedure.
6.1 Language setup
1. Scroll the language list to find the
desired language and hold the
desired language pressed to set it.
www.aeg.com14

1/4
Svenska
English
Deutch
Italiano
Francais
Language
SV
DE
EN
IT
FR
2. The following screen pops up:
• tap on OK to confirm the
language:
• tap on Change to change it.
Change OK
You’ve selected:
English
2/4 Language
6.2 Time setup
1. Scroll the hour and minute bars to
the right or to the left to set the
current time.
Set Clock 13:45
46>
14>
<44
<12
45min
13h
3/4 Info
2. Tap on the Set Clock bar to set the
time.
Set Clock 13:45
46>
14>
<44
<12
45min
13h
3/4 Info
3. The following screen pops up:
• tap on OK to confirm the set
time.
• tap on Change to change it.
Change OK
Current time:
13:45
4/4 Set Clock
6.3 More settings
After you set the time, the More settings
screen pops up.
Later Set
More settings to get the best results
from this machine will follow. Set
them now?
More Settings
If you tap on Later, the programme list
screen appears and you can set the
desired programme.
Cottons
ColourPro
OKOPower
3h01min
Cottons Eco
Synthetics More
1200
40
If you tap on Set, proceed with next
settings.
6.4 Detergent Dosing
You can set the average quantity of
detergent suggested on the detergent
packaging.
Later Set
Advise on detergent level for best
results. Set now or later?
Detergent advice
1. Tap on Set. The following window
pops up.
ENGLISH 15

Later OK
Set detergent dose for full load in
10 kg machine. Refer to detergent
packaging for recommended dosage
Detergent advice
2. Tap on OK to enter the Detergent
Dosing menu.
3. Tap on the Detergent Type 1 or
Detergent Type 2 bar.
Detergent Dosing OFF
Info
Detergent Type 1
Detergent Type 2
4. Scroll the submenu bar right or left to
set the detergent dosage in ml that
matches with the average dosage
suggested on the detergent
packaging.
Detergent Type 1 OFF
Info
60>
<40 50 ml
5. Tap on the Detergent Type 1 bar.
The following window pops up. Tap
on OK to confirm your choice.
Change OK
50
You’ve selected:
Detergent advice
6.5 Wi-Fi
The startup ends with following dialog
window.
OK
Settings complete. To connect your
machine to WiFi, see instructions in
user manual
OK
Refer to the "Wi-Fi Connectivity setup"
section in the "Settings" chapter.
7. TOUCH SCREEN
Each time you turn the appliance on, the
Start-up Screen appears on the touch
screen.
AEG
13.45
After a few seconds, the programme list
screen appears proposing Cottons as
default programme.
Cottons
ColourPro
OKOPower
3h01min
Cottons Eco
Synthetics More
1200
40
If you don't scroll the programme list up
and down, in a few seconds the
programme summary screen appears. To
return to the programme list screen just
tap on the programme name (e.g.
Cottons).
www.aeg.com
16

Cottons
Max 10 Kg
1h07min
More
1200
40
The summary screen shows:
• Programme maximum load,
programme name.
Cottons
Max 10 Kg
1h07min
More
1200
40
• Programme duration. If selected, this
area can also show the delayed start
or the Time Save symbol.
Cottons
Max 10 Kg
1h07min
More
1200
40
• The currently selected options. The
shortcut allows to enter the
additional option menu.
Cottons
Max 10 Kg
1h07min
More
1200
40
When a shortcut is visible on
the summary screen, it is
possible to enter an option/
setting menu by just tapping
on the relevant shortcut.
The different option/setting menus can
be scrolled:
•up and down, or
•right or left.
To set some options or settings it is
sufficient to change the status from OFF
to ON just tapping on the relevant bar.
Programmes, options and
settings can also be set by
turning the programme dial
and in horizontal submenus
the desired choice can be
set just tapping on the
arrows <or >.
8. WI-FI CONNECTIVITY SETUP
This chapter describes how to connect
the smart appliance to the Wi-Fi network
and to link it to mobile devices.
By this functionality you can receive
notifications, control and monitor your
appliance from your mobile devices.
ENGLISH 17

To connect the appliance to enjoy the
full range of features and services you
need:
• Wireless network at home with
internet connection enabled.
• Mobile device connected to wireless
network.
Frequency 2.412 - 2.472 GHz
for European mar-
ket
Protocol IEEE 802.11b/g/n
two stream radio
Max Power <20 dBm
8.1 Installing and configuring
"My AEG"
When connecting the appliance to the
application, stand near it with your smart
device.
Make sure that your smart device is
connected to the wireless network.
1. Go to the App Store on your smart
device.
2. Download and install the App "My
AEG" .
3. Make sure you started a Wi-fi
connection in the appliance. If not,
read the next paragraph 'Configuring
the appliance wireless connection'.
4. Start the application. Select the
country and language and login with
Your email and password. If you do
not have an account, create a new
one following the instructions in "My
AEG" .
5. Follow the instructions on the App
for the appliance registration and
configuration.
A message appears on the appliance
display to confirm that the configuration
was successful.
8.2 Configuring the appliance
wireless connection
1. In the programme list screen, tap on
the shortcut to enter the setting
menu.
2. Tap on the Wi-Fi bar to switch the
connection on .
A pop-up message will appear, the icon
starts flashing and wireless module
begins starting up. It may take about 2
minutes before it is ready.
Cancel
Starting up
This might take up to 2 minutes.
Have your App ready
Wi-Fi
When the wireless module is ready, a
pop-up message will appear to inform
you, that the access point will be open
for about 3 minutes.
Cancel
Trying to connect to App
Access point will be open for 3
minutes.
Wi-Fi
3. Configure the "My AEG" app on
your smart device.
4. If the connectivity is configured, a
message appears on the appliance
display to confirm that the
configuration was successful.
OK
Wi-Fi
Connected!
Signal strenght is good, 4/5
5. Tap on OK to get back to the
machine settings list.
6. Tap on Programmes to get back to
the programme list screen.
Switching the wireless
connection off
1. In the programme list screen, tap on
the shortcut to enter the setting
menu.
2. Tap on the Wi-Fi bar, and a new
menu is shown.
3. Tap on Turn off .
www.aeg.com
18

Removing the wireless
credentials
1. In the programme list screen, tap on
the shortcut to enter the setting
menu.
2. Tap on the Wi-Fi bar, and a new
menu is shown.
3. Tap on Reset network.
8.3 Remote Start Mode
You can start and stop a washing
programme remotely.
When the App is installed and the
wireless connection is complete, the
Remote Start Mode option will appear
among the available options of each
programme.
To activate the remote start:
1. In the programme list screen, select
the desired programme.
2. When the programme summary
screen appears, tap on More to
enter the option list.
3. Tap on the Remote Start Mode bar
to activate it (ON status). The
following message pops up:
Cancel
Please press Start
To activate Remote Start Mode
Remote Start Mode
<Back
4. Press the Start/Pause button to
activate the Remote Start Mode.
The indicators and appear on the
programme summary screen and the
door is locked.
If the door is open, the
Remote Start Mode is
deactivated.
If you pause or stop the
cycle remotely, the door
remains locked. To unlock
the door, you should be in
front of the appliance and
press the Start/Pause. To
avoid accidental unlocking
of the doors, the Child Lock
option can be activated.
WARNING!
If the temperature and level
of the water in the drum are
too high and/or the drum
still rotates you cannot open
the door.
8.4 Over-the-air update
The App may propose an update for
downloading new features.
The update is accepted via App only.
If a programme is running, the App
notifies that the update will start at the
end of the programme.
During the update, the appliance shows
a message telling that update is running.
The appliance will usable again at the
end of the update, without any
notification about successful update.
If an error occurs, the appliance warns
that update has failed: just press any
buttons or turn the knob to return to
normal use.
ENGLISH 19

9. BEFORE FIRST USE
During installation or before
first use you may observe
some water in the appliance.
This is a residual water left in
the appliance after a full
functional test in the factory
to ensure the appliance is
delivered to customers in
perfect working order and is
no cause for concern.
1. Make sure that all transit bolts have
been removed from the appliance.
2. Make sure that the electrical power is
available and the water tap is open.
3. Pour 2 litres of water into the
detergent compartment marked by
.
This action activates the drain system.
4. Pour a small quantity of detergent
into the compartment marked by
.
5. Set and start a programme for cotton
at the highest temperature without
any laundry in the drum.
This removes all possible dirt from the
drum and the tub.
10. PROGRAMMES
10.1 Programme Chart
Programme Programme description
Washing programmes
Cottons White cotton and coloured cotton. Normal, heavy and light
soil.
Cottons Eco White cotton and coloured cotton. Normal, heavy and light
soil.
Cottons energy saving programme. This programme at 60ºC
with a load of 10 kg is the reference programme for data en-
tered in the energy label, in compliance with 96/60/EC Direc-
tive. Set this programme to have a good washing results and
decrease the energy consumption. The time of the washing
programme is extended.
Synthetics Synthetic items or mixed fabric items. Normal soil.
Wash&Dry programme
NonStop 3h/3kg Mixed fabrics (cotton and synthetic items). Complete pro-
gramme to wash and dry laundry loads up to 3 kg in one go. It
only lasts 3 hours.
Washing programmes
Delicates Delicate fabrics such as acrylics, viscose and mixed fabrics
requiring gentler washing. Normal soil.
Silk Machine and hand washable silk and other delicate fabrics .
Drum movements are so gentle that is possible to treat even
very delicate garments. Run a complete wash and dry cycle to
reduce creases.
www.aeg.com20