Aeramax Am iv User manual

INSTALLATION GUIDE

AeraMax

PRO Air Quality Control System: AM IV

Please read instructions carefully before installing unit

ENGLISH

AeraMax® PRO Air Quality Control System: AM IV

1. Access panel

2. Filters

3. Filter frame

4. Main Assembly

5. Power Switch

6. Access panel latch

7. Access panel lock

8. Rear housing assembly

9. Control panel

10. Filter frame window

KEY

Fig 1

SAFETY

TOOLS REQUIRED FOR INSTALLATION

WARNING: To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before beginning any installation work.

Confirm no electrical wiring, utility pipes, or duct work is located directly behind the installation / drilling area.

On a stud wall, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to an existing stud.

• Electricdrill,drillbits(notincluded)

• #2Phillipsand#2FlatHeadscrewdrivers(notincluded)

• Wirenuts(notincluded)

• Level(notincluded)

• Mountingtemplate(included)

Fig 2

8”

PARTS PROVIDED FOR INSTALLATION

PRODUCT INSTALLATION GUIDELINES

Americans with Disabilities Act (ADA):

Be sure to follow all ADA guidelines pertaining to “Objects protruding

into a circulation path.” For more information visit www.ada.gov.

Place the mounting template provided on the wall where the air

purifier is to be installed. If air purifier is being mounted high on

the wall make sure the top edge of the unit is positioned at least

8”inches(21cm)belowtheceilingtoallowforfilterreplacement

(seeFig2).

• DrywallAnchors-10mmOD

• PanHeadPhillipsScrews

Place the air purifier face up on a

flat, stable work surface. Open the

access panel by pressing in latches

oneachsideoftheunit(Fig3).

Disconnect main housing assembly

from rear housing assembly.

Separate main housing from rear

housing.Liftmainhousingassembly

away from rear mounting housing

(Fig8).

Open access panel and remove

filter assembly by pulling out on

top of side edges of frame, then

lifting. NOTE: remove all plastic

wrapfromfilters(Fig4).

Removethesixhousingscrews(Fig5&6)andsetasideforre-assembly.

At the location of the two upper

housingcornerscrews(Fig5),insert

a flat head screwdriver and gently

twist to release tab as shown in Fig

7. This will disconnect main housing

assembly from the rear housing

assembly.

MOUNTING REAR HOUSING AND MAIN ASSEMBLY

REAR HOUSING INSTALLATION & WIRING

Test the electrical outlet box first to ensure rated power requirements are met before beginning installation.

Remove air purifier from its shipping carton and remove all packing material.

Reference rear housing and locate desired mounting location. Again, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to

an existing stud.

Fig 3

Fig 7

Fig 4

Fig 8

Fig 5

Fig 6

Fig 10

Fig 11

Using provided template ensure electrical

outletboxislocatedbehindcablehole(A)

in Rear Housing assembly (Fig 9). Drill

holes and place anchors in wall.

If mounting on concrete, cinder block or

brick type walls route the wires through

the“punch-out”holemarked(B)inFig9.

Check for washers at all mounting

screw locations (Fig 10). Pull wires

from electrical outlet box through

hole in rear housing. Align housing

over anchors and securely install all

mounting screws.

Attachwiresfromelectricaloutletboxtowireslocatedinsiderearhousingusingwirenuts.Matchupline(black)andneutral(white)wires(Fig11).Makesure

all connections are made in accordance with federal, state and local codes and regulations.

Fig 9

Make sure filters are in correct order

- pre-filter / carbon filter / HEPA

filter-andinsertedintofilterframe

(Fig16).

IMPORTANT: Make sure filter

detection area aligns with window

infilterframe(Fig17).

Close front panel by pressing

firmly until both sides latch closed

(Fig19).

The power connector (B, in Fig

12) will carry power from the rear

housing to the main housing once

the assemblies are fully seated. The

main assembly will attach to the rear

housing assembly by the four screws

previouslyremoved(Fig5&6).Two

snaphooks(A,inFig12)willholdthe

main and rear assemblies together

until the screws can be installed.

Carefully align the main assembly

with the rear housing assembly.

Slowly press into place until snap is

heard, and there is no gap between

the assemblies (Fig 13). The unit

should now support its own weight.

Open front panel by pressing

latches on both sides of unit. Allow

door to open fully. Insert filters

– IMPORTANT: make sure filter

detection window is aligned in

upperrightcorner(Fig18).

To restrict access to the control panel

and filters the unit can be locked. To

lock, insert the key provided and

rotateclockwise¼turn(Fig21).

Once the unit is closed re-establish

power.Lightsonthecontrolpanelwill

be visible through the lens, indicating

theunitisoperational(Fig20).The

power light indicator will flash once

a second.

Install six screws (previously removed) to secure main assembly to rear

housingassembly(Fig14&15).

RE-INSTALLING FILTERS

LOCKING ACCESS PANEL

MAIN ASSEMBLY INSTALLATION

WARNING: To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before continuing any installation work.