AERF WIRELESSBAND 1.0 User manual

Instruction Manual
(WIRELESSBAND 1.0)
1. GENERAL
One channel wireless system communication for either resistive, mechanical or pneumatical safety edges.
1 2 3
1 2 3
1 2 3 4 5 6 7
Select 8K2 or mechanical safety
edge in transmitter options (option 1)
Select 8K2 or mechanical safety
edge in transmitter options (option 1)
TEST RELAY
(Choose transmitter
option 3 for contact
NO or NC)
OUTPUT TYPE
- Contact (3-5)
- Resistive safety edge 8k2 (3-4)
3.3 RECEIVER OPTION SELECTOR
3.1 RECEIVER CONNECTIONS
2.1 TRANSMITTER REGULAR CONNECTIONS
2.2 OTHER TRANSMITTER CONNECTIONS
2.3 TRANSMITTER OPTION SELECTOR
+/~-/~
12/24V
AC/DC
Safety OK
Fail / Sensor active /
Sensor not memorized
VCC1 C SVCC2 BTEST
C
B
8K2
C
BS
S
Safety
Edge Common Inhibitor
Safety
Edge Common Inhibitor
3.2 LED INDICATOR
LED ON - Security OK
LED OFF - Obstacle detected
2. TRANSMITTER 3. RECEIVER
1
5
2
3
4
6
7
1
2
3
5
4
6
7
1- Terminals
2- Battery1 CR2032
3- Battery 2 CR2032
4- LED
5- DIP - Switch
6- Push button
7- Antenna
1- Terminals
2- LED 1
3- Push button
4- DIP - Switch
5- LED 2
6- Buzzer
7- Antenna
1
2
1
2
3
4
1234
ON
1234
ON
1234
ON
1234
ON
1234
ON
1234
ON
1234
ON
1234
ON
TRANSMITTER
FREQUENCY
AUTOMATIC
FREQUENCY
AGILITY
RECEIVER
TYPE TEST
CLASS 2 Enabled (Normative UNE-EN 13849-2)
Disabled (Default)
N.O. contact
N.C. contact
Enabled
Disabled
869,85 Mhz (same as transmitter)
868,95 Mhz (same as transmitter)
12
ON
12
ON
12
ON
12
ON
TRANSMITTER
FREQUENCY
SAFETY EDGE
TYPE
Resistive safety edge
Contact safety edge
869,85 Mhz (same as receiver)
868,95 Mhz (same as receiver)
1 - 2
Contact Inhibition
Translation of the original instructions
1.1 SAFETY INDICATIONS
- Reaction time < 60ms
- EN13849-1 Cat2 PL-C with TEST.
- Device with SELV/PELV Power Supply
IP55 2 yrs
Battery 100m 1 Ch
Output
14 tx
EN
06/11/18
WIRELESSBAND 1.0

PROG. 10s
PROG. PROG.
1.5s 3s
1 X BEEP
PRESS
RECEIVER
KEEP IT
PRESSED SAVE & EXIT
2 X BEEP
WAIT
RELEASE
# BEEPS
PROG.
1.5s
PROG. 10s
SAVE & EXIT
2 X BEEP
1 X BEEP
1 X BEEP PRESS
TRANSMITTER
BUTTON
RELEASE
PRESS
RECEIVER WAIT
4. START-UP
5. PROGRAMMING PROCESS
CODE MEMORIZATION
MEMORY RESET
- Installation, start-up, modification and updating of the
system may only be carried out by a qualified person.
- Switch off the operating voltage before working on the system.
- The system doesn’t have fuse protection. It is
recommended to include exterior protection from 100mA
and to 250mA.
- In case of any hypothetical issue, please do a memory
reset (point 4.).
MEMORY FULL INDICATOR
Several beeps for 10 seconds when trying to memorize a new transmitter.
LOW BATTERY INDICATOR
4 beeps each time a message is received from a programmed transmitter. Both, warning LED and buzzer are activated simultaneously.
Receiver suply voltatge
Transmitter suply voltatge
Battery life
Receiver memory
Receiver Output
Receiver Power consumption
Ball pressure test (IEC 695-10-2)
Pollution degree
Protection class (IEC 60529)
Frecuency Channels
Range
Working temperature
Software
Rated transient over voltage
Transmitter power consumption
Machine Security Normative
Reaction time
12/24 AC/DC
2x lithium battery 3V DC type CR2032
2 years
14 transmitters
Relay,micro disconnection 1B
0.5 W - 12 V / 1,2 W - 24 V
PCB (125ºC) WRAP (75ºC)
2
Ip55
868.95MHz & 869.85MHz
100m
-35ºC to +55ºC
Class A
330V
Transmitting 17mA / stand by 16uA
13849-2008 PL-C Category 2, with TEST
60 ms
TECHNICAL SPECIFICATIONS WARNING!!
CE DECLARATION OF CONFORMITY
For more information visit the website www.aerf.eu
1. INSERT BATTERIES
+-
12/24V 0V
AC/DC
2. CONNECT RECEIVER
POWER SUPPLY
3. CHECK OPTION
SELECTORS
4. CARRY OUT CODE
MEMORIZATION (POINT 4.)
PROG.
5. INSTALL AND WIRE
TRANSMITTER ON DOOR
7. INSTALL AND WIRE
RECEIVER
9. TEST SAFETY EDGE
ON DOOR
CONTROL
UNIT
220V
M
8. TURN ON POWER
SUPPLY
OK?
OK?
6. MINIMUM DISTANCE
1 m.
TRANSMITTER
RECEIVER
>1m 12/24V
ON
2 - 2
2
0
3
R
2
C
+
l
l
i
l
t
h
e
c
u
i
m
2
0
3
R
2
C
+
l
l
i
l
t
h
e
c
u
i
m
2
0
3
R
2
C
+
l
l
i
l
t
h
e
c
u
i
m
12
EN
06/11/18
WIRELESSBAND 1.0