Aerotrak 9001 User manual

AEROTRAK®
CLEANROOM CONDENSATION
PARTICLE COUNTER
MODEL 9001
QUICK START GUIDE
P/N 6010559, REVISION C
OCTOBER 2017

2
This guide will walk you through the setup screens required to make the
unit run and log data. The logged data can then be downloaded to a USB
thumb drive.
IMPORTANT
Before turning the unit ON, make sure the fill and drain bottles are
connected appropriately. If the fill and drain bottles are not connected, the
unit cannot keep the wicks wet. Fill the fill bottle with ultrapure, de-ionized
or distilled water only. DO NOT use tap water or filtered water.
•Connections to the unit for the Fill and Drain bottle are shown below.
•The top connector connects to the fill bottle and the bottom connector
connects to the drain bottle.

Quick Start Guide 3
•Power the unit ON using the “power” button. The Cleanroom
Condensation Particle Counter (CPC) will take about 10 to 15 minutes
to warm-up. The warm-up screen is shown below.
•Wait for all the warm-up screen “reds” to turn green. If you really need
to exit the warm-up screen, press the Power Down button on the
instrument and then select “Cancel” from the Power Down screen.
This will bring you to the Main page shown below.

4 AeroTrak Cleanroom Condensation Particle Counter Model 9001
•Typically, if the unit is turned on and the temperatures have not
reached their stable state, you will not be able to run the unit and a
message “warming up” will be displayed. You can setup the unit while
the unit is warming up.
•For instrument setup, go to the “Setup” tab.
•Click on “Device.”
•Select “Maintenance."

Quick Start Guide 5
The maintenance screen has a number of useful features as described
below.
Field Description
Prime Wicks Whenever wicks are replaced or the unit is fully
shut off for prolonged periods of time (> 1 day),
wicks need to be primed. Click “Prime Wicks”
and the instrument will go through a priming cycle
that injects water to all three wicks. Make sure the
fill and drain bottles are connected to the unit. Unit
will go through the prime cycle on its own.
Drain Wicks The instrument needs to be drained before
transporting it to a different location. Make sure
the drain bottle is connected and the fill bottle is
disconnected. Note that if the fill bottle is
connected, you will never be able to drain the
wicks. Unit will go through the drain cycle on its
own.
Enable Flow Turns the pump on or off. See information below
to purge the system.
New Wicks Reset
DO NOT USE.
This is for TSI use only.
Bottle Counter
Reset If you refill the bottle with ultrapure, de-ionized, or distilled water, click “Bottle Counter Reset.” This
allows the instrument to keep track of the amount
of water used and notify you if the fill bottle is
getting empty.
IMPORTANT
When shipping make sure you drain the water from the unit by clicking on
“DrainWicks”. First, you must disconnect the water fill bottle from the unit
and keep the drain bottle connected to the device.

6 AeroTrak Cleanroom Condensation Particle Counter Model 9001
Taking Data
•To take data, go to the “Setup” tab from the initial screen and select
“Recipes.”
•The easiest way to log data once a minute is by using the default
recipe with no Zone. Click on “Edit” to change the sample time and the
duration of the sampling.
•Click on the “Timing” tab. Options are provided to enter start delay,
sample time and cycles or the number of samples you want to take. To
run the instrument continuously, cycles can be set to ∞as shown
below. Hold time is the time you want to wait between taking samples.
More often, it is set to 0 to take samples continuously.

Quick Start Guide 7
•Save the recipe and exit back to the setup screen.
•To setup the instrument to log data using a computer or FMS software,
you can query the IP address of the instrument on the setup screen by
clicking on the icon “Info” as shown below.
•To change the Cleanroom CPC’s date and time, click on “Device” icon
in the Setup screen and then on the “Date and Time” icon.

8 AeroTrak Cleanroom Condensation Particle Counter Model 9001
•To run the instrument, go back to the main screen. Click on the “Run”
button as shown below. Instrument should run and log data. The
instrument can be stopped whenever you desire. To review and
download data, insert a USB thumb drive first and then click on the
Data tab. If you do not have a USB thumb drive, you can still review
the data record by record.
•To download data, click on the “USB thumb drive” icon as shown
below.

Quick Start Guide 9
•Click on “Export As” to save to a file. You can enter the filename as
shown below.
•To download data selected by Zone and optionally filtered by date,
make the choices on the form below and click on “Export” button.
•To download data selected by Sample (record) Number and optionally
filtered by date, click the “Select by Record” button, make the choices
on that form, and click the “Export” button.

10 AeroTrak Cleanroom Condensation Particle Counter Model 9001
•Data will be saved to the USB thumb drive as shown below.
•To clear any logged data, on the Setup Screen, click on “System” icon
and then click on “Clear Samples” as shown below.