AGFEO AS 40 User manual

Telekommunikation
AS 40 - Modul
Installation of the module
Safty notes ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
!Before unlocking the cover, remove the 230 V mains plug
from the telephone system.
Opening the housing ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
Unlocking the cover
- Pull out the black bolt slightly to the side
using a narrow srewdriver blade (about 2
mm wide) until you can grip the bolt
(Fig.1 and 2).
- Hold the bolt and pull it right out turning
it slightly (Fig. 2 and 3).
You can use the bolt as a module extrac-
tor when exchanging a module.
Removing the cover
- Grip the underside behind the finned
cover that covers the telephone system’s
connection panel.
- Pull the edge of the cover down slightly to
unlatch it. Detach the cover towards you.
Bolt
Unlocking the cover Fig. 1 Fig. 3Fig. 2
Removing the module from the packaging - Safety measure ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
Before removing the module from the
packaging and before inserting the
module in the AS 40, touch the metal
shield of the PC/printer socket on the
bottom of the AS 40 briefly with your
finger. This discharges any possible
electrostatic charge and protects
electrostatically sensitive components of
the AS 40 and the module.
1

- Insert the module vertically with the large
connector strip at the top in the top and
bottom guide rails of a slot. You can
select freely between slots 1 to 4.
- Push the module carefully back until the
connectors grip and the lug of the
module snaps into the lock.
Installation of the module¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
- Stick the enclosed label showing the
module connections above the module
slot on the housing.
- Please see the operating instructions -
chapter ‘Installation’ of the telephone
system AS 40 for information about
connecting the module.
Startup ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
- Switch on the telephone system by
plugging in the 230 V- mains plug.
!
Identnr. 523666
Modifications and errors reserved.
Printed in Germany
0986
Closing the housing¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
Replacing the cover
- First hook in the cover at the top of the
housing. The three latches engage behind
the edge of the housing.
- Press onto the cover until it latches into
the housing at the bottom.
Locking the cover
- Insert the bolt with the hook facing
downwards in the cover opening, turning
the bolt slightly (Fig.4).
- Push the bolt in past the pressure point up
to the stop (fig. 5)
Locking the cover Figure 4 Figure 5
AGFEO GmbH & Co. KG
Gaswerkstr. 8
D-33647 Bielefeld
The housing must be locked before plugging in the
telephone system’s 230 V- mains plug.
2