AGI Express CPE250 User manual

Re-branding Instructions
Express 250 and CPF50
Electric Vehicle Charging Stations
*Tamper-proof T25 screwdriver required
CPE250 ~ 20 mins CPF50 ~ 2 mins
Two technicians recommended

3. Disconnect the power cable from the LED display
2.Use a T25 Torx driver to loosen the two captive
screws on the bottom edge of the area light bar.
1.ENSURE POWER TO THE UNIT IS OFF
BEFORE BEGINNING
4.Gently push the LED screen upwards so that
the mounting brackets are no longer secured, and
disconnect the wires shown
CPE250

5.Gently lift the front panel until the mounting brackets
are loose, and set the panel to the side.
6. The orange ChargePoint signing is held to the panel
using a weak adhesive, gently remove and replace the
sign with the rebranding replacement
7. Use a T25 Torx driver to unscrew the M5 screws
and washers connecting the touchscreen ground strap
to the frame (d).
8. Loosen the retention knobs (a), allowing the
touchscreen beam (b) to slide up vertically. Re-tighten
at the highest position
9. Gently tilt the bottom of the touchscreen up to allow
the removal of the middle vent below

10. Lift the middle vent up, and set aside
11. You should now be able to remove the orange
ChargePoint sign from the lower portion of the
unit, and slide the new one into place.
12. Align the guide tabs on the middle vent panel to the
corresponding slots on the Express 250’s frame. Ensure
the lower sign is correctly captured as you carefully push
the middle panel down until it is fully seated.

13. With hand pressure, swing the touchscreen down.
Loosen both retention knobs (a), allowing the
touchscreen beam (b) to slide up vertically. Re-tighten
the knobs at the highest position.
14. Tilt the bottom of the touchscreen inside the slot in
the middle vent panel, aligning the notch in the center
of the bottom edge (c) to the guide ridge inside the
panel slot.
15. Keeping pressure on the edge of the touchscreen to
properly seat it inside the panel, loosen the knobs to
lower the screen again. Re-tighten the knobs to secure
it.
16. Use a T25 Torx driver to re-secure the M5 washers
and screws to the frame (d) Torque to 4 Nm (35 in-lbs)
17. Using two hands, align the guide tabs on the front
upper panel with the corresponding slots. While
pushing the panel into place, push the bottom edge
and its sign inward to position them inside the
groove in the middle vent panel and engage the
edge of the sign.

18. Using two hands, align the guide tabs on the front
upper panel with the corresponding slots. While pushing
the panel into place, push the bottom edge and its sign
inward to position them inside the groove in the middle
vent panel and engage the edge of the sign.
19. Carefully push the panel down until it is firmly seated
20. While holding the LED display near the opening at the top of the Express 250, connect its five cables to
their corresponding connectors on the back of the display (each connector is keyed to fit only into its matching
port):
a. Communications cable (USB-A)
b. Holster light cable
c. Area light cable (x2)
d. Power cable (24 V)
**Leave the area light bar cable (e) loose.

21. Angle the top edge of the LED display under the
light bar on the Express 250. Starting at the top, align and
slide the LED display guide tabs into the corresponding
slots. Ensure the lower sign is correctly captured by the
bottom edge of the LED display. Push the bottom into
place until firmly seated.
Note: Keep the area light cable routed out the top of the
display, and then reconnect.
22. Ensure the gasket on each end of the new
area light bar is properly seated around the plastic tab.

23.Use a T25 Torx driver to tighten the two captive
screws on the bottom edge of the area light bar.
24. Reconnect power, and then give the unit
about 5 minutes to connect to the ChargePoint
network. It will run a self-assessment, and once
done the LED panel should display "Available."
If it doesn't, contact ChargePoint support at
1-888-758-4389 and ask them to see if there are
any issues on their end.
CPF50
1. Remove the plug from the holster
2. Locate the tabs on the bottom of the face
plate (shown below), and pull to pop the face plate
off.
3. Slide the new face plate over the holster, and
push down to secure tightly. Make sure that each
corner of the face plate is securely fastened.
4. Return plug to holster.