Agilent Technologies 4352B User manual

Agilent 4352B Revision 01.02 Firmware
Installation Kit (04352-65402 )
Installation Manual
Agilent Part No. 04352-90402
Printed in JAPAN July 2000

Notice
The information contained in this document is subject to change without notice
.
This document contains proprietary information which is protected by copyright. All rights are
reserved. No part of this document may be photocopied, reproduced, or translated to another
language without the prior written consent of the Agilent T
echnologies.
Agilent T
echnologies Japan, Ltd.
Component T
est PGU-Kobe
1-3-2, Murotani, Nishi-ku, Kobe-shi,
Hyogo
,651-2241 Japan
c
 Copyright Agilent Technologies Japan, Ltd. 1998, 2000

Typeface Conventions
4
HARDKEYS
5
Labeled keys on the instrument front panel are enclosed in
45
.
NNNNNNNNNNNNNNNNNNNNNNNNNN
SOFTKEYS
Softkeys located to the right of the LCD are enclosed in
NNNNN
.
Safety Symbols
General denitions of safety symbols used on equipment or in manuals
.
Note denotes important information. It calls attention to aprocedure
,
practice
,condition or the like
,whichis essential to highlight.
iii

1
General Information
Introduction
This chapter describes the Kit and lists the contents of the Kit.
The Firmware Installation Kit
The purpose of this kit is to install the rmware to 4352B .The kit is used for rmware
upgrades
,and for rmware installation after repairing the A1 CPU board.
Contents of the Firmware Installation Kit
See Table 1-1 for the kit contents
.If anything is missing, contact the nearest Agilent
T
echnologies oce
.
T
able 1-1. Contents of the Kit
P
art Number Description Qty
.
04352-18402 Flexible Disk (Rev 01.02)1
5080-3949 Label \Firmware Rev 01.02"1
04352-90402 Installation Manual (This manual) 1
General Information 1-1

2
Installation
Introduction
This chapter describes the rmware installation procedure
.
Firmware Installation Procedure
P
erform the following steps to install the rmware into the 4352B .
1. While pressing
4
Preset
5
key
,turn on the 4352B.The bootloader screen as shown in Figure 2-1
will be displayed.
Figure 2-1. Bootloader Menu Screen
2. Insert the furnished exible disk into the disk drive.
3. Press
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
PREVIEW DISK . The update disk revision will be displayed.
Installation 2-1

4.
Conrm the displayed \Update Disk Revision" is 01.02 and press
NNNNNNNNNNNNNNNNNNNN
Return
.
5.
Press
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
SYSTEM UPDATE
,
NNNNNNNNNNNNNNNNNNNNNNNNNN
CONTINUE
to install the 4352B rmware from the exible disk to the
4352B ash memory
.It
will take about a few minutes
.
6.
After \Update Complete" is displayed, press
NNNNNNNNNNNNNNNNNNNN
REBOOT
to reboot the 4352B .
7.
Press 4
System
5 ,
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
FIRMWARE REVISION
to conrm the current rmware revision. If \POWER
ON TEST F
AILED" isn't displayed on the LCD and the new rmware revison is correctly
displayed, the rmware installation is successfully completed.
8. Put the rmware revision label on the 4352B's rear panel as shown in Figure 2-2.
Figure 2-2. Location of the Firmware Revision Label
Note
The Firmware Installation Kit can be used to install the rmware into more
than one unit of the 4352B.In
this case
,order additional rmware revision
labels (Agilent P/N: 5080-3949).
2-2 Installation