Agilent Technologies E5070A ENA Series User manual

Agilent E5070A/E5071A ENA Series RF Network Analyzers
Installation and Quick Start Guide
Second Edition
FIRMWARE REVISIONS/SERIAL NUMBERS
This manual applies directly to instruments that have the firmware revision 2.00.
For additional information about firmware revisions, see Appendix A.
Agilent Part No. E5070-90011
April 2002
Printed in Japan

2
Notices
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Agilent Technologies.
Agilent Technologies Japan, Ltd.
Component Test PGU-Kobe
1-3-2, Murotani, Nishi-ku, Kobe, Hyogo, 651-2241 Japan
© Copyright Agilent Technologies Japan, Ltd. 2001, 2002
Manual Printing History
The manual’s printing date and part number indicate its current edition. The printing date
changes when a new edition is printed (minor corrections and updates that are incorporated
at reprint do not cause the date to change). The manual part number changes when
extensive technical changes are incorporated.
December 2001 First Edition (part number: E5070-90001)
April 2002 Second Edition (part number: E5070-90011)

3
Safety Summary
The following general safety precautions must be observed during all phases of operation,
service, and repair of this instrument. Failure to comply with these precautions or with
specific WARNINGS elsewhere in this manual may impair the protection provided by the
equipment. Such noncompliance would also violate safety standards of design,
manufacture, and intended use of the instrument. Agilent Technologies assumes no liability
for the customer’s failure to comply with these precautions.
NOTE The E5070A/E5071A complies with INSTALLATION CATEGORY II as well as
POLLUTION DEGREE 2 in IEC61010-1. The E5070A/E5071A is an INDOOR USE
product.
NOTE The LEDs in the E5070A/E5071A are Class 1 in accordance with IEC60825-1,
CLASS 1 LED PRODUCT
• Ground the Instrument
To avoid electric shock, the instrument chassis and cabinet must be grounded with the
supplied power cable’s grounding prong.
• DO NOT Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of inflammable gasses or fumes.
Operation of any electrical instrument in such an environment clearly constitutes a
safety hazard.
• Keep Away from Live Circuits
Operators must not remove instrument covers. Component replacement and internal
adjustments must be made by qualified maintenance personnel. Do not replace
components with the power cable connected. Under certain conditions, dangerous
voltage levels may remain even after the power cable has been disconnected. To avoid
injuries, always disconnect the power and discharge circuits before touching them.
• DO NOT Service or Adjust the Instrument Alone
Do not attempt internal service or adjustment unless another person, capable of
rendering first aid and resuscitation, is present.
• DO NOT Substitute Parts or Modify the Instrument
To avoid the danger of introducing additional hazards, do not install substitute parts or
perform unauthorized modifications to the instrument. Return the instrument to an
Agilent Technologies Sales and Service Office for service and repair to ensure that
safety features are maintained in operational condition.
• Dangerous Procedure Warnings
Warnings, such as the example below, precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be followed.
WARNING Dangerous voltage levels, capable of causing death, are present in this instrument.
Use extreme caution when handling, testing, and adjusting this instrument.

4
Safety Symbols
General definitions of safety symbols used on the instrument or in manuals are listed
below.
Instruction Manual symbol: the product is marked with this symbol when it is necessary for
the user to refer to the instrument manual.
Alternating current.
Direct current.
On (Supply).
Off (Supply).
In-position of push-button switch.
Out-position of push-button switch.
A chassis terminal; a connection to the instrument’s chassis, which includes all exposed
metal structure.
Stand-by.
WARNING This warning sign denotes a hazard. It calls attention to a procedure, practice, or
condition that, if not correctly performed or adhered to, could result in injury or
death to personnel.
CAUTION This Caution sign denotes a hazard. It calls attention to a procedure, practice, or condition
that, if not correctly performed or adhered to, could result in damage to or destruction of
part or all of the instrument.
NOTE This Note sign denotes important information. It calls attention to a procedure, practice, or
condition that is essential for the user to understand.

5
Typeface Conventions
Sample (bold) Boldface type is used when a term is defined or
emphasized.
Sample (Italic) Italic type is used for emphasis and for titles of
manuals and other publications.
Sample menu/button/box/tab Indicates a menu/button/box/tab on the screen
labeled “Sample” which can be selected/executed
by clicking. “menu”, “button”, “box”, or “tab“
may be omitted.
key Indicates a hardkey (key on the front panel or
external keyboard) labeled “Sample.” “key” may
be omitted.
[Sample] Indicates the hardkey whose key label is
“Sample“.
[Sample] - Item Indicates a series of key operations in which you
press the [Sample] key, make the item called
“Item” on the displayed menu blink by using the
[ ¯]or in other ways, and then press the [Enter]
key.

6
E5070A/E5071A Documentation Map
The following manuals are available for the E5070A/E5071A.
•User’s Guide (Part Number: E5070-900x0, attached to optional ABA)
This manual describes most of the basic information necessary to use the
E5070A/E5071A. It provides a function overview, detailed operation procedure for
each function (from preparation for measurement to analysis of measurement results),
measurement examples, specifications, and supplemental information. For
programming guidance on performing automatic measurement with the
E5070A/E5071A, please see the Programming Manual.
•Installation and Quick Start Guide (Part Number: E5070-900x1, attached to
optional ABA)
This manual describes installation after it is delivered and the basic operation
procedures for applications and analysis. Refer to this manual when you use the
E5070A/E5071A for the first time.
•Programmer’s Guide (Part Number: E5070-900x2, attached to optional ABA)
This manual provides programming information for performing automatic
measurement with the E5070A/E5071A. It includes an outline of remote control,
procedures for detecting measurement start (trigger) and end (sweep end), application
programming examples, command reference, and related information.
•VBA Programmer’s Guide (Part Number: E5070-900x3, attached to optional ABA)
This manual describes programming information for performing automatic
measurement with internal controller. It includes an outline of VBA programming,
some sample programming examples, a COM object reference, and related
information.
NOTE The number position shown by “x” in the part numbers above indicates the edition number.
This convention is applied to each manual, CD-ROM (for manuals), and sample programs
disk issued. Here, “0” indicates the initial edition, and each time a revision is made this
number is incremented by 1. The latest edition allows the customer to specify Option ABJ
(Japanese) or Option ABA (English) of the product.

Contents
7
1. Introduction of This Manual
Contents of This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Overview of the E5070A/E5071A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. Installation
Checking the Shipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operating Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ventilation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Protection Against Electrostatic Discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ensuring Adequate Free Space around Analyzer for Immediate Disconnection of Power Cable in Case of
Emergency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing Front Handles/Rack Mounting Flanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
How to Install the Handle Kit (Option 1CN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
How to Install the Rack-mount Kit (Option 1CM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
How to Install the Rack-mount and Handle Kit (Option 1CP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting the Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting the Mouse and Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting the BNC Cable (Option 1E5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connecting a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting the Ecal Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Power Supply and Blown Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Verification of the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Verification and Connection of Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Blown Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Starting the E5070A/E5071A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning the Power ON and OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Disconnection from Supply Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Setting the Internal Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cleaning Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Maintaining an N-type Connector on Each Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Self-test When Turning on the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Considerations When Shipping to a Service Center Due to Breakdown or Other Problem . . . . . . . . . . . 36
3. Quick Start Guide
Names and Descriptions of E5070/E5071A parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Display Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Three Methods of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Operating Method Using Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Operation Method Using a Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Operation Method Using the Touch Screen (Option 016) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Basic Measurement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Basic Measurement Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Measurement Example of a Bandpass Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
STEP 1. Determining Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

8
Contents
STEP 2. Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
STEP 3. Connecting the Device Under Test(DUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
STEP 4. Analyzing Measurement Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
STEP 5. Outputting Measurement Results (Save) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
A. Manual Changes
Manual Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

9
1. Introduction of This Manual
1 Introduction of This Manual
This chapter provides an overview of this manual to use this manual efficiently and
describes the features of the Agilent E5070A/E5071A briefly. See this manual first when
you use the E5070A/E5071A for the first time.

10 Chapter 1
Introduction of This Manual
Contents of This Manual
Contents of This
Chapter
Contents of This Manual
This Quick Start Guide has been prepared to quickly familiarize users with the
E5070A/E5071A basic oeration and measurement. The following shows the contents of
this manual.
NOTE The Chapter 3, “Quick Start Guide,” on page 37 describes only a measurement example of
the bandpass filter. For other measurement examples, see Chapter “Measurement
Examples” in the E5070A/E5071A User’s Guide.
oContents of This Manual page 10
Describes the chapter configuration of this manual (Installation and Quick Start
Guide) and its contents.
oOverview of the E5070A/E5071A page 11
Describes the major features of the E5070A/E5071A.
oChapter 1, “Introduction of This Manual”
This chapter provides an overview of this manual to use this manual efficiently
and describes the features of the Agilent E5070A/E5071A briefly. See this
manual first when you use the E5070A/E5071A for the first time.
oChapter 2, “Installation”
This chapter provides information about how to set up the Agilent
E5070A/E5071A RF network analyzer, and about daily maintenance.
oChapter 3, “Quick Start Guide”
This chapter describes the functions of parts on the front panel and display area
of the Agilent E5070/E5071A RF Network Analyzer. Using the example of
measuring a bandpass filter, you will quickly learn how to easily operate the
E5070/E5071A by understanding the basic measurement procedures and
operation of the E5070/E5071A.
oAppendix A, “Manual Changes,”
This appendix contains the information required to adapt this manual to versions
or configurations of the E5070A/E5071A manufactured earlier than the current
printing date of this manual.

Chapter 1 11
Introduction of This Manual
Overview of the E5070A/E5071A
1. Introduction of This Manual
Overview of the E5070A/E5071A
The E5070A/E5071A RF Network Analyzer is an instrument that can quickly and
accurately evaluate multi-port device measurements. The major features of the
E5070A/E5071A are described as follows.
1. You can equip the instrument with a measurement frequency range at high frequencies
required when you measure RF multi-port devices such as mobile communication
components (E5070A:300 kHz to 3 GHz; E5071A:300 kHz to 8.5 GHz) and with up to
four test ports.
2. Simultaneously measuring all the built-in test ports realizes high-speed measurement,
while executing full-port calibration removes error factors thoroughly to achieve high
accuracy measurement.
3. The built-in balanced measurement function, matching circuit simulation function, and
port impedance transformation function enables you to correctly evaluate RF balanced
devices such as balanced SAW filters.
4. The ease of operation based on the use of a GUI (Graphic User Interface), excellent
connection compatibility with peripherals, and graphical programming environment
created by the built-in VBA enables the user to efficiently process measurement data.
5. The instrument is capable of simultaneously displaying up to nine measurement
channels as well as up to nine measurement parameters per channel.

12 Chapter 1
Introduction of This Manual
Overview of the E5070A/E5071A

13
2. Installation
2 Installation
This chapter provides information about how to set up the Agilent E5070A/E5071A RF
network analyzer, and about daily maintenance.

14 Chapter 2
Installation
Contents of this
Chapter
oChecking the Shipment on page 15
After you receive the analyzer, check all the items in the packing container.
oEnvironmental Requirements on page 18
Describes the system requirements needed to install the E5070A/E5071A and
how to secure space for heat radiation.
oInstalling Front Handles/Rack Mounting Flanges on page 21
Shows how to mount the front handles used to transport the E5070A/E5071A
and how to install the flanges needed to install it in a rack.
oConnecting the Accessories on page 24
Provides information for connecting the mouse, keyboard, BNC cable, and Ecal
module to the E5070A/E5071A.
oPower Supply and Blown Fuses on page 29
Shows how to check the power supply as well as check and connect the power
cable. This section also describes what to do for a blown fuse.
oStarting the E5070A/E5071A on page 31
Describes turning on/off of the Power switch and cutting off the power supply.
In this section you can also find how to set the internal clock.
oDaily Maintenance on page 35
Describes the daily maintenance for the E5070A/E5071A.

Chapter 2 15
Installation
Checking the Shipment
2. Installation
Checking the Shipment
After you receive the analyzer, carry out checks during unpacking according to the
following procedure.
WARNING When unpacking the analyzer, if the external face of the analyzer (such as the cover,
front/rear panel, LCD screen, power switch, and port connectors) appear to be
damaged during transport, do not turn on the power switch. Otherwise, you may get
an electric shock.
Step 1. Check that the packing box or shock-absorbing material used to package the analyzer has
not been damaged.
NOTE If the packing box or shock-absorbing material has been damaged, leave the packing box
and shock-absorbing material as is until other inspection items are checked as follows:
Step 2. Check the packaged items supplied with the analyzer for any damage or defects.
Step 3. By referring to Table 2-1 and Figure 2-1, check that all packaged items supplied with the
analyzer have been provided as per the specified options.
Step 4. After checking, if one of the following applies, contact your nearest Agilent Technologies
sales and service office.
1. The packing box or shock-absorbing material used to package the analyzer has been
damaged or the shock-absorbing material has traces where extreme force has been
applied.
2. A packaged item supplied with the analyzer has mechanical damage or defects.
3. A packaged item supplied with the analyzer is missing.
4. A fault has been detected in the subsequent operation check of the analyzer.
If an abnormality is detected in step 1, contact the company that transported the analyzer as
well as your nearest Agilent Technologies sales and service office. For inspection by the
transport company, save the packing box, shock-absorbing material, and packaged items as
you received them.

16 Chapter 2
Installation
Checking the Shipment
Table 2-1 Items Packaged with the E5070A/E5071A
Name Agilent Product/
Part Number
Qty
Standard Accessories
oE5070A/E5071A*1
*1.Figure 2-1 shows the E5070A/E5071A main unit when Option 004 (4-port S-parameter
test set) is specified.
E5070A/E5071A 1
oKeyboard*2
*2.Not supplied with the analyzer if Option 1A2 (without keyboard) is specified.
-1
oMouse*3
*3.Not supplied with the analyzer if Option 1CS (without mouse) is specified.
-1
oPower cable*4
*4.This accessory varies from country to country. For the power cable option, see Figure
2-10.
-1
Options
oManual (Option ABA)*5
*5.This is not supplied with the analyzer if Option 0B0 (without manual) is specified. The
‘x’ in the part number of the Manual, CD-ROM (of the manual), or sample program
disk is a number that is incremented each time a revision is made, with ‘0’ regarded as
the first edition. The network analyzer will always be supplied with the latest versions
of these items.
• Userís Guide E5070-900x0 1
• Installation and Quick Start Guide E5070-900x1 1
• Programmerís Guide E5070-900x2 1
• VBA Programmerís Guide E5070-900x3 1
• CD-ROM (of the manual)*6
*6.The CD-ROM contains the same information as in the User’s Guide, Installation and
Quick Start Guide, Programmer’s Guide, VBA Programmer’s Guide and two Sample
Program Disks.
E5070-905xx 1
• Sample program disk E5070-180x0 1
• E5070A/E5071AVBA sample program disk E5070-180x1 1
oBNC cable (Option 1E5) 8120-1838 1
oHandle Kit (Option 1CN)*7
*7.This accessory is not shown in Figure 2-1. For the detail contents, see Table 2-4 on
page 21.
5063-9229 1
oRack Mount Kit Without Handles (Option 1CM)*7 5063-9216 1
oRack Mount Kit With Handles (Option 1CP)*7 5063-9223 1

Chapter 2 17
Installation
Checking the Shipment
2. Installation
Figure 2-1 E5070A/E5071A Accessories

18 Chapter 2
Installation
Environmental Requirements
Environmental Requirements
Set up the E5070A/E5071A where the following environmental requirements are met.
Operating Environments
Ensure that the operating environment meets the following requirements.
NOTE Above environmental requirements are NOT for the specifications and measurement
accuracy of the analyzer, but for the operating environment of the analyzer.
Temperature 5 °C to 40 °C
Temperature range at the
error-correction
23 °C ±5 °C (< 1 °C deviation from the temperature
when performing the error-correction )
Humidity < 90 % at +40 °C (non-condensation)
Altitude 0 to 2,000 m (0 to 6,561 feet)
Vibration 0.5 G maximum, 5 Hz to 500 Hz

Chapter 2 19
Installation
Environmental Requirements
2. Installation
Ventilation Requirements
To ensure safety requirements, the specifications and measurement accuracy of the
analyzer, you must keep environmental temperature within the specified range by
providing appropriate cooling clearance around the analyzer or, for the rackmount type, by
forcefully air-cooling inside the rack housing. For more information on environmental
temperature to satisfy the specifications and measurement accuracy of the analyzer, see
“Specifications And Supplemental Information“ in the E5070A/E5071A User’s Guide.
When the environmental temperature around the analyzer is kept within the temperature
range of the operating environment specification (See Section “Operating Environments”
on page 18 ), the analyzer conforms to the requirements of the safety standard.
Furthermore, under that temperature requirement, the analyzer still conforms to the
requirements of the safety standard even when placing the analyzer with cooling clearance
as follows:
Figure 2-2 Ventilation space at the installation
Requirements
Back ³180 mm
Sides ³0 mm (both right and left)

20 Chapter 2
Installation
Environmental Requirements
Protection Against Electrostatic Discharge (ESD)
Set up a static-safe work-station to protect the electronic components from the damage by
the electrostatic discharge (ESD) as shown in Figure 2-3. Table 2-2 shows the accessories
available that provide ESD protection.
Figure 2-3 Example of the static-safe work-station
Ensuring Adequate Free Space around Analyzer for Immediate
Disconnection of Power Cable in Case of Emergency
As described in “Disconnection from Supply Source” on page 33, the power supply is
disconnected by removing the power cable’s connector plug from either the AC outlet or
the E5070A/E5071A unit. When installing the E5070A/E5071A, ensure that there is
sufficient free space around the unit to permit quick disconnection of the plug (from AC
outlet or E5070A/E5071A unit) in case of emergency.
Table 2-2 The accessories available that provide ESD protection
Name Agilent Part Number
Static-control table mat and earth ground wire 9300-0797
Wrist-strap cord 9300-0980
Wrist-strap 9300-1383
Heel-straps 9300-1169