agri supply BB5H User manual

Pull Type Drag Scraper
BB5H, BB6H, & BB7H
Please Read This Manual BEFORE Using This Implement

CAUTION
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE
THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING TO
BEGIN ASSEMBLING THIS MACHINE
1. Select an area for assembly that is clean and free of any debris which might cause
persons working on the assembly to trip.
2. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork trucks or other
mechanical devices.
3. Preview the assembly instructions in your operator’s manual before proceeding
further.
4. If the assembly instructions call for parts or assemblies to be blocked up, use only
blocks material that is good condition and is capable of handing the weight of the
assembly to be blocked. Also insure that the blocking material is on a clean, dry
surface.
5. Never put hands, or any part of body, under blocked up assemblies if at all possible.
6. After completing assembly, thoroughly inspect the machine to be sure that all nuts,
bolts, hydraulic fittings or any other fastened assemblies have been thoroughly
tightened.
7. Before operating the machine, thoroughly read the operation section of your
operator’s manual.
8. Before operating, read the machine section of your operator’s manual to be sure that
any parts requiring lubrication, such as gearbox, to avoid any possible damage.
9. Before operating equipment –if you have any questions regarding the proper
assembly or operation, contact you dealer or representative.

EQUIPMENT SAFETY GUIDELINES
1. Never use alcoholic beverages or drugs which can hinder alertness or coordination
while operating this equipment. Consult your doctor about operating this machine
while taking prescription medications.
2. Review the safety instructions with all users annually.
3. This equipment is dangerous to children and persons unfamiliar with its operation. The
operator should be a responsible adult familiar with farm machinery and trained in this
equipment’s operations. Do not allow persons to operate or assemble this unit
until they have read this manual and have developed a thorough understanding
of the safety precautions and of how works.
4. Never exceed the limits of a piece of machinery.
5. Do not modify the equipment in any way. Unauthorized modification may impair the
function and could affect the life of equipment.
OPERATIONAL SAFETY
1. The use of this equipment is subject to certain hazards which cannot be protected
against by mechanical means or product design. All operators of this equipment must
read and understand this entire manual, paying particular attention to operating, prior
to using. If there is something in this manual you do not understand, ask your
supervisor, or your dealer, to explain it to you.
2. Personal protection equipment including hard hat, safety glasses, safety shoes, and
gloves are recommended during assembly.
3. Never permit any person other than the operator to ride or board the tractor or
implement at any time. Never allow anyone to ride on the implement!
4. A heavy load can cause instability in driving a tractor. Make sure the front or rear of the
tractor is properly counter-balanced with weights, Always drive slowly-especially
around turns. An unstable tractor could steer badly and possibly tip over, causing
injury or death.
5. Most accidents occur because of neglect or carelessness. Keep all helpers and
bystanders at a safe distance.
6. Use stabilizer bars, adjustable sway chains, or sway blocks on your tractor lift arms to
keep the rear blade from swinging side to side. Adjust as tightly as practical for best
performance.

7. Do not operate close to ditches or creeks. Slow down when operating
over rough ground.
8. When adjusting the angle of the moldboard assembly, be sure that your feet
are never under the rear blade.
9. Be careful to avoid catching the rear blade on stumps or other immovable
objects.
MAINTENANCE SAFETY
1. Keep all persons away from operator control area while performing
adjustments, service, or maintenance.
2. Periodically tighten all bolts, nuts and screws and check that all cotter
pins are properly installed to ensure unit is in a safe condition.
3. Never use your hands to locate a hydraulic leak on attachments. Use a small
piece of cardboard or wood.
4. Never replace hex bolts with less than grade five bolts unless otherwise
specified. Refer to bolt torque chart for head identification marking.
STORAGE SAFETY
1. Store the unit in an area away from human activity. Do not permit children to
play on or around the stored unit.
2. Make sure all parked machines are on a hard, level surface and engage
all safety devices.
3. At the end of the working season or when the box blade will not be used
for a long period, it is good practice to clean off any dirt or grease that may
have accumulated on the blade and any of the moving parts.
4. Inspect the blade for loose, damaged or worn parts and adjust or replace if
needed.
5. Repaint parts where paint is worn or scratched to prevent rust.
6. Store box blade in a clean, dry place.
ALWAYS OBEY ALL SAFETY
RULES!
ALWAYS BE CAREFUL!

Parts Assembly
Item
Description
Qty
1
Scraper Box Frame
1
2
Tilt Axle
1
3
Towbar
1
4
Hitch Clevis
1
5
Scraper Blade
1
6
Bolt M16*45
4/5/6
7
Flat Washer Φ16
4/5/6
8
Spring WasherΦ16
4/5/6
9
Nut M16
4/5/6
10
Pin Φ22*130
2
11
Pin Lock Ring
4
12
Pin Φ19*105
2
13
Oil Cylinder
1
14
Cylinder Joint
2
15
Seal Ring
2
16
Hydraulic Hose 3.5m
1
17
Hydraulic Hose 3.2m
1
18
Wheel
2
19
Mut M24*180
2
20
Flat Washer Φ24
2
21
Lock Nut M24
2
22
Bolt M20*70
2
23
Lock Nut M20
2