Ronix RA-2702 User manual

RA-2702
AIR RIVETER

USER MANUAL 1
SPECIFICATIONS
Model 2702
TractionPower 1045 Kg-f
Stroke Lenght 16mm
Capacity 4.8mm, 4.0m, 3.2mm, 2.4mm
Air Pressure 5.5 ~ 6 bar (79-87 PSI)
Avg. Air Consumption 1.48 Liter/Stroke
Air Inlet 1/4" PT (NPT)
Weight 1.5 Kg
Accessories
2 pcs Spare Jaw, Jaw case, Jaw pusher,
Jaw pusher spring, Oil bottle,
2 pcs Service spanner,
Nose piece: 4.8mm, 4.0m, 3.2mm, 2.4mm
PART LIST
Hydroulic Cylinder
Trigger
Air Inlet
Air Cylinder
Nail Container
Nozzle

AIR RIVETER
2
Read this manual carefully before installing, operating, servicing
or repairing.
WORKING ENVIRONMENT
1) Using these tools in any potentially explosive environment is strictly
prohibited.
2) itis always recommended that these types of tools mUst be operated
when standing on asolid or firm location.
3) always Use these tools in awell ventilated area.
4) slipping, stUmbling and falling are the major caUses of potential serioUs
injUry, therefore, aclean and clUtter free sUrface in the working area
before operating the tools is strongly recommended.
AIR SUPPLY AND CONNECTION REQUIREMENTS
1) the maximUm recommended air pressUre dUring operation mUst not
exceed 87 psi (6 bar). higher air pressUre may create Unsafe operating
conditions for the tool and the User.
2)the compressed air shoUld be cooled and have awater filter installed
at the oUtlet end of the compressor. even with awater filter installed,
some water may still condense in the piping or hose and will enter the
tool mechanism caUsing prematUre damage to the tool. therefore, it is
recommended to install an air filter-lUbricator device somewhere between
the tool and the compressor.
3) always Use an air compressor of the proper capacity to operate each
tool.
4) clean the hose with ablast of compressed air before connecting the
hose to the air tool. this will prevent both moistUre and dUst inside the
hose from entering the tool and caUsing possible rUst or malfUnction.

USER MANUAL 3
IDEAL SYSTEM CONNECTION
Shut-Off Cock
Water Drain
Air Tool
Shut-Off Cock
Oil Filter
Refrigerated Air Dryer Air CompressorAir Tank
Filter, Regulator&Lubricator
Pressure Check
Point
WARNING!
1) This tool should only be used as a hand operated tool. It is powered
by compressed air and is not insulated against electric shock.
2) This tool is specially designed for riveting sheet metals together. Any
application or use of this tool other than what it is designed for is strictly
prohibited.
3) Always wear hearing protection, safety goggles and proper clothes
when operating this tool.
4) Make sure that the all the specifications of the rivets to be used are
compatible with this tool.
5) Check the protection against the ejecting of rivet stem in place and is

AIR RIVETER
4
operative.
6) Make certain to stand on a solid or firm location and keep body in
well-balanced position while operating this tool.
7) Always turn off the air supply and disconnect the air hose before
changing rivet nose or making adjustments on this tool.
8) Release the throttle lever to avoid danger if there is a failure of energy
supply or when connecting or disconnecting the air hose.
9) Beware if the compressed air hose breaks unexpectedly, or is being
connected or disconnected improperly. This whipping action may cause
injury.
MAINTENANCE
1. Disassemble and clean all the components inside the front housing
with pressured air.
2. Take the piston assembly apart from the air cylinder, clean and apply
some pneumatic oil to both piston and cylinder walls.
3. Rehabilitate the tool by assembling everything back reversely.
PROCEDURE TO CHANGE NOSE PIECE
Step 1: Use Multi-Wrench spanner to remove the Nose Piece.
Step 2: Choose the size you need and use Multi-Wrench spanner to
assemble the Nose Piece.
Note:
Noses are equipped on the tool

8