Agria 2294 071 User manual

Before commissioning the machine, read operating
instructions and observe warnings and safety instructions!
Operating Instructions No. 998 428GB 02.12
6120
&
Front Mounted Sweeper
2294 071, -081
2294 171, -181
2294 271, -281
2294 071, -081 80 cm
2294 171, -181 100 cm
2294 271, -281 120 cm
Operating Instructions
Translation of the original operating instructions

2agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281
Index
Amount of delivery, Symbols .2
1. Safety Instructions............ 3-6
Due Use ............................................ 3
2. Specifications....................... 7
Designation of Parts, Fig. A.............. 7
3. Devices and Operating
Elements
Mounting Extension Guards............. 8
Mounting pivoting lever..................... 8
Attaching the Rotary Brushes .......... 9
Connecting port.............................. 10
Mounting to the Base Machine ...... 10
Fixing Points ................................... 10
Sweeping Height Adjustment ......... 11
Side Adjustment ............................. 11
Brush Speed ................................... 11
Implements ..................................... 12
4. Commissioning and
Operation
Working........................................... 13
Danger Zone................................... 14
5. Maintenance
Brush Drive..................................... 15
Self-aligning bearing....................... 16
Support Wheel ................................ 17
Sweeper.......................................... 17
Cleaning.......................................... 18
Storage ........................................... 18
Wear Parts ...................................... 18
Conformity Declaration ......... 19
Symbols, Name Plate,Index
Please complete:
MachineType No........................
Identification No....................
......................................................
Date of Purchase: ......................
For name plate,
refer to p7/fig.A/20.
Only use original agria spare
parts!
Specifications, figures, and dimen-
sionsstatedintheseinstructions are
not binding. No claims can be de-
rivedfromthem.Wereserve theright
for improvements without changing
these instructions.
Amount of delivery:
l Operating instructions
l Front mounted sweeper
Symbols
Warning – Danger
Important Information
Engine Start
P.T.O.Shaft
Visual inspection
Open brake
Lubricating point, grease
gun
Lubricating point, brush
èSee Operating
Instructions

agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281 3
Before starting the engine, read the op-
erating instructions and note:
Warning
Thissymbolmarks allparagraphswhich
affect yoursafety.Pass all safetyinstruc-
tions to other users and operators.
Due Use
The sweeper, including the implements
approved by the manufacturer, is
intended for sweeping up loose dirt
and snow on paved surfaces when
used with a hand-controlled single-
axle driving machine (due use).
Any other type of operation is consid-
ered undue.The manufacturer is not li-
able for any damages resulting from
undue use, for which the risk lies with
the user alone.
Due use includes compliance with
manufacturer’s instructions on opera-
tion, maintenance and repair.
Any unauthorized changes to the
sweeper render manufacturer liability
null and void.
General Instructions on
Safety and Accident
Prevention
Basic Rule:
The standard accident prevention regu-
lations must be adhered to, as well as
all other generally accepted rules gov-
erning operational safety, occupational
health and road traffic regulations.
For drives on public roads, the national
traffic code applies.
Accordingly,check the sweeperfor road
and operational safety each time you
take up operation.
Only persons familiar with the sweeper
and instructed on the hazards of opera-
tion are allowed to use, maintain and
repair the sweeper.
Teenagers of 16 years or younger may
not operate the sweeper!
Only work in good light and visibility.
Operator’s clothes should fit tight.Avoid
wearing loose fitting clothes.Wear solid
shoes.
Note the warning and instruction signs
onthesweeperforsafeoperation.Com-
pliance is for your own safety.
When transporting the sweeper on ve-
hicles or trailers outside the area to be
sweeped, ensure that the engine is
turned off and the wheel dogs are
engaged.
Careful with rotating tools – keep at a
safe distance!
Beware of coasting tools.Before you
start anymaintenance orrepairon them,
waituntiltoolshavecome to a complete
stop.
1. Safety Instructions

4agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281
1
Foreign poweredparts shear andcrush!
Riding on the machine during operation
is not permitted.
Implements and their weight affect the
driving, steering, braking, and tip-over
characteristics of the sweeper. There-
fore, ensure steering and braking func-
tions are sufficient. Match operating
speed to conditions.
Working Area and Danger
Zone
The user is liable to third parties work-
ing within the sweeper’s working range.
Staying in the danger zone is not per-
mitted.
Check the immediate surroundings of
the sweeper before you start it. Watch
out for children and animals.
Before you start work, clear the area
from any foreign object. During opera-
tion,alwayswatch outforfurtherobjects
and remove them in time.
Careful! Dirt and stones may get air-
borneduring sweeping.Peopleandani-
mals must keep out of this area.Watch
outforvehicles,windowpanesandother
objects to avoid damage.
For operationinenclosed areas,ensure
that a safety distance is kept to enclo-
sures to prevent damage to tools.
Operation and Safety
Devices
BeforeYou Start the Engine
Become familiar with the devices and
operating elements and their functions.
Above all, learn how to turn the engine
off quickly and safely in an emergency.
Ensure that all protective devices are
mounted and positioned to provide
protection.
The P.T.O.shaft must be covered by
protective cap when the attachment
device is removed.
Operation
Never leave the operator’s position at
thehandlebarswhile sweeperisat work.
Never adjust the operating handles dur-
ing work – danger!
During operationthe operatormustkeep
at a distance as defined by the handle-
bars, especially when turning the ma-
chine.
Riding on the machine during operation
or in transport is not permitted.
If clogging occurs in the brushes or in
the implement, turn off the engine and
cleanthebrushes or theimplementwith
an appropriate tool.
In case of damage to the sweeper or to
the implement, immediately turn off the
engine and have it repaired.
If steering causes problems, immedi-
ately bring the sweeper to a halt and
turnitoff.Havethemalfunctionremoved
without delay.
1. Safety Instructions

agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281 5
To prevent the sweeper from sliding on
slopes, make sure it is secured by an-
other person using a bar or a rope.This
person must be located at a higher po-
sition than the vehicle and at a safe dis-
tance from the attachment at work.
If possible, always work horizontally on
the slope.
End of Operation
Never leave the sweeper unattended
with the engine running.
Before you leave the sweeper, turn off
the engine.
Implements
Only mount implements with the engine
and the implement drive switched off.
Always use appropriate tools and wear
gloves when changing implements and
parts thereof.
For mounting and dismounting imple-
ments bring stands into proper position
and ensure stability.
Secure base machine and implements
against rolling off (wheel chocks).
Beware of injuries while coupling imple-
ments.
Mountimplementsas specifiedandonly
couple at specified points.
Weights
Always fit weights onto appropriate
weight mounting devices.
Maintenance and
Cleaning
Never carry out any maintenance or
cleaning with the engine running.
Before you work on the engine, always
remove spark plug connector (petrol
engine only).
Check regularly and, if necessary, re-
place all guards and tools subject to
wear and tear.
Damaged brush rollers must be
replaced!
Keep sweeper and implement clean to
avoid risk of fire.
Check nuts and bolts regularly for tight
fit and re-tighten, if necessary.
Do not carry out repairs like welding,
grinding, drilling, etc. on structural and
safety-relevant parts (e.g. coupling
devices, etc.)!
Aftermaintenanceandcleaning, ensure
that you re-install all safety devices and
guards and adjust them properly.
Only use original agria spare parts.All
other commercial spare parts must cor-
respondtoquality and technicalrequire-
ments specified by agria.
1. Safety Instructions

6agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281
Explanation of
Warning Signs
With engine running, keep at a safe distance.
Do not touch moving machinery parts.Wait until they
have come to a complete stop.
With engine running, keep at a safe distance from the
rotary brushes!
Before any cleaning, maintenance, and repair work
shut off the engine and pull spark plug connector or
ignition key.
Signs
When working with the machine, wear individual pro-
tective ear plugs.
Wear protective gloves.
Wear solid shoes.
1. Safety Instructions
1

agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281 7
2. Specifications
Article no.:............................2294 071 ....-081 ... -171 .....-181 .....-271 .. -281
Working width: [cm] ........................ 80 .......80 .....100 ...... 100 ...... 120 ... 120
Rotary brushes: ....................... coarse ..... fine coarse ...... fine .coarse ... fine
Weight: [kg] approx......................... 37 .......38 ....40,5 ........ 42 ........ 44 ..... 46
Dimensions:b [mm] ................. 800 .....800 ...1000 ....1000 .... 1200 .1200
l [mm] .................. 690
h [mm] ................. 630
Rotary brushes Ø: .................................................................................. 350 mm
Brush Speed:....................................................steplessly 130 min-1 to 230 min-1
Drive:....................................................................... V-belt - variator - worm gear
Drive speed: .................................................................................max. 950 min-1
Support Wheel (double wheel): .................................................. Ø125 x 40 mm
Transmission oil:................................................................. SAE 855 W-90 0,3 l.
11
8
7
1
2
14
16 18
20
21
Fig. A
1Right rotary brush
2Left rotary brush
7Clamping strip
8Rubber strip
9Main guard
19
Designation of Parts
10 Extension guard
11 Pivoting lever
14 Crank handle
16 Hood
17 Fixing eye rear
18 Fixing eye front
19 Dial brush speed
20 Name plate
21 Connecting port
22 Support wheel (double wheel)
10
9
17
22
Designation of Parts
The maintenance intervals are between 2, 8, 25 and 50 hours or 1 year.
bl
h

8agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281
100 cm
3. Devices and Operating Elements
120 cm
Extension Guards
l Fit the clamping strips (7) and rubber
strips(8) on the left and right each 5
screws:
- for a working width of 80 cm to the main
guard
for working widths of 100 or 120 cm to
the extension guard.
l Attach the extension guards (10) to the
main guard (9) to match brush width (100
or120).Usethreehexheadbolts andlock
nuts for each guard.
Mounting
pivoting lever
l Mount the pivoting le-
ver (11) using bolt (12)
and 2 spring cotter pins
(13) to the sweeper.
80 cm
7
8
13
11
13
12
10
9
10
9

agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281 9
3
3. Devices and Operating Elements
1Right rotary brush
2Left rotary brush
3Nut cap
4Tensioning anchorage
5Disc
6Nut





Attaching the
Rotary Brushes
Wear safety gloves
to attach/remove the
brushes. Danger of
crushing.
Mountthediscsontoboth
sides of the rotary brushes.
Push the tensioning
anchorage through the left
rotary brush.
Push the tensioning
anchorage with the rotary
brush through the drive shaft
from the left - insert groove
(S) on rotary brushes into
cam (N) of the drive plate.
slide right rotary brush
onto tensioning anchorage
- insert groove on rotary
brushes into cam of the drive
plate.
Screw on and tighten he-
xagonal nut.
To remove the brushes, re-
verse the above order.

10 agria Front Mounted Sweeper 2294071, -081, -171, -181, -271, -281
èOConnecting port
l Lightly grease the connecting port
and shaft
Mounting to the
Base Machine
èBase machine
l For two-wheeled tractor turn
steering spar for front attachment
l Turn off PTO shaft
To remove reverse the above order.
Fixing Points
Loading belts must be hung into the
eyes intended for this purpose for
lifting, retrieving and lashing to
ensure safe transportation.
Check loading belt for damage;
replace it, if necessary.
Do not use any loading devices with
sharp edges (e.g. sharp-edged
hooks, lugs etc.).
Never walk or remain under
moving loads. Danger!
3. Devices and Operating Elements
3