Aigis Mechtronics PT9420-2PSL User manual

2
x
16.67
0.656
9
0.2
3
.55
7.1
0.28
7.14
Ø
82
.
6
3.25
(
O
M
M
INSTALLATION AND OPERATING INSTRUCTIONS
MEDIUM DUTY PAN/TILTS
PT9420-2PSL
PT9420-1PSL

2
SAFETY PRECAUTIONS
This label may appear on the bottom of the unit due to space limita-
tions.
The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
UNPACKING
Unpack carefully. This is electro-mechanical equipment and
should be handled with care.
Check for the following items:
• Model number of unit.
• Instruction Manuals in addition to this manual:
PT9418 Series, PT9420 Series
If an item appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper. If any items
are missing, notify Aigis Mechtronics.The shipping carton is
the safest container in which the unit may be transported.
Save it for possible future use.
SERVICE
If the unit ever needs repair service, the customer should
contact Aigis Mechtronics.
1INSTALLATION
This publication should be used in conjunction with the
Instructions for Use for the PT9418 Series, PT9420
Series except as noted herein.
This installation should be made by qualified
service personnel and conform to the National
Electrical Code and applicable local codes.
1.1 Model Designation
Continuous Pan Models with Pre-Position
Model Rated Motor Voltage Pan
No. Voltage Range Range
PT9420-2PSL 24 VAC, 60 Hz 21.6 to 26.4 0° to 360°
PT9420-1PSL 24 VAC, 50 Hz 21.6 to 26.4 0° to 360°
These models allow 360 degree rotational (pan) operation.
They have no pan stops.These units can be manually panned
left or right or they can be panned continuously left or right
by auto-pan activation.Auto-Pan activation requires wiring
connections to pin 16 (Pan Left), pin 18 (Pan Right), and pin
19 (Common). See Wiring Diagram.
For pre-position operation, these units require wiring connec-
tions to pins 1 through 4 and pin 15, and the use of a con-
troller or receiver/driver with the pre-position function.
1.8Connector Assembly
WIRE DESIGNATION AND PIN CONNECTIONS
Figure 2: Pin Outs
PT9420-2PSL, PT9420-1PSL 360° Pre-Position Models
Pin Number Color
1: Pan +5V Orange2
2: Pan Sense (3) Wht/Blk/Yel2
3: Pan -5V Wht/Blk/Red2
4:Tilt Sense Wht/Blk /Brn 2
5: Lens Common Green2
6: Zoom Blue2
7: Focus Violet2
8: NC1
9: NC1
10.Accessory White2
11.Accessory Red2
12.Accessory Yellow2
13: NC1
14: NC1
15: Pan Sense (2) White/Orange
16: Pan Left White
17: NC1
18: Pan Right Violet
19: P/T Common Blue
20:Tilt Up Brown
21:Tilt Down White/Yellow
22: Ground Green/Yellow
23: Camera AC-Line Black2
24: Camera AC-Neutral White2
Notes
1. NC -- No Connection, do not use.
2. (Color Codes) indicate feed-thru wiring to camera/housing.
CAUTION:TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSON-
NEL.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE UNPROTECTED COMPONENTSTO RAIN
OR MOISTURE.

3
3WIRING DIAGRAMS
Wiring Diagram - 360º Models with Pre-Position

100 0048 001 AIG 10/02
Printed in U.S.A.
©2002 Aigis Mechtronics
1124 Louise Road,Winston-Salem, NC 27107-5450
Tel: [phone] Fax: [phone]
Data subject to change without notice