Aiphone IS-IPDVF-HID User manual

Pg. 1
IS-IPDVF-HID
Vandal Resistant IP Color Video Door Station
with Built in Proximity Card Reader
The IS-IPDVF-HID is an IS Series IP color video door station and an HID ProxPoint Plus Card
Reader, built onto the same stainless steel faceplate. The card reader provides electronic access to a
building through a separate Access Control System, which is not supplied by Aiphone.
The IS-IPDVF-HID will connect directly to a network switch.
-INSTRUCTIONS-
NAMES & FUNCTIONS:
1. Camera 5. Name Placard
2. Microphone 6. Call status indicator
3. LED Light 7. Call button
4. Speaker 8. Prox Reader
FEATURES:
• All-in-one solution: Communication product &
card reader
• If a card is missing or malfunctioning,
audio/video communication can provide user
verication
• Standard Wiegand output to access panel
• Convenience of installing combined components
IS-IPDVF-HID
1
2
3
4
5
6
7
8
PACKAGE CONTENTS:
IS-IPDVF-HID
Vandal-resistant Door Station
Security Driver
Flush backbox &
tamper-resistant screws
Blank name
placard
INSTALLATION:
• Forushmounting,cutaholeinthewallandusethe
supplied back box.
Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D
• For surface mounting, use the SBX-ISDVFP surface
mount box.
This box can mount to a standard 1 gang box or to
anyatsurface.

Pg. 2
IS-IPDVF-HID Instr.
0113JD
Aiphone Corporation
1700 130th AVE NE
Bellevue, WA 98005
[phone]
Fax: [phone]
WIRING DIAGRAM:
IS-IPDVF-HID
IS-IPMV
Wiegand Wire Color
+ DC (5-16V) Red
Ground Black
Data0 Green
Data1 White
Shield Ground Drain
Green LED Orange
Red LED Brown
Beeper Yellow
Hold Blue
Card Present Violet
Connect the reader to the host according to the
wiring table below and the host installation guide.
TESTING & OPERATION:
• Whenpowerisappliedtothecardreader,theLEDwillashgreenthree(3)timeswhilethe
beeper beeps simultaneously. The LED will then turn red. This indicates that the microcontroller
is operating properly.
• Present an ID card to the reader (hold card directly in front of reader). The LED will momentarily
turn green while the beeper beeps once, indicating that the card was read successfully.
SPECIFICATIONS:
CARD READER:
Reader type: 6005B ProxPoint Plus
Power Source: 5 ~ 16V DC
Max Voltage: 18V DC
Current: 30mA (Avg); 75mA (peak)
Terminations: Color-coded pre-wired pigtail
Wiring Distance: 500’
Operating Temp: 14° ~ 140°F / -10° ~ 60°C
Operating Humidity: 0-95% relative humidity
non-condensing
CAMERA:
Camera unit: CMOS camera
Scanning line: 525 lines
Min. illumination: 5 Lux at 1’6”
Terminations: RJ45 jack for audio/video
Screw terminals for door release
Operating Temp: 14° ~ 140°F / -10° ~ 60°C
Wiring Distance: 328’ with Cat5e/6 cable to switch
Dimensions: 12-3/8” H x 7” W
w/SBX-ISDVFP: 12-7/16” H x 7-1/16” W x 2-13/16” D
(top), 1-13/16” D (bottom)
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
• For proper regulatory compliance, the drain wire should be disconnected at the power
supply end of the cable.
• Changesormodicationsnotexpresslyapprovedbythepartyresponsiblefor
compliance could void the user’s authority to operate the equipment.
• The Reader is intended to be powered from a limited power source output of a
previously certifed power supply
TOLL FREE TECHNICAL SUPPORT:
[phone]
E-MAIL: [email protected]
NO
COM
NC
To Strike
& Power
CAT-5e
CAT-5e
Note: Please refer to the IS Series literature for
complete installation and programming instructions.