Aiphone IS SERIES User manual

IS SERIES
Local System
QuikStart Programming Guide
This is an abbreviated programming manual, addressing basic program settings for an
IS Series Local System. A complete set of instructions (IS Series Installation Manual / IS Series
Operation Manual / IS Series Settings Manual) can be found on the CD provided with the IS-CCU Central Control Unit.
ATTENTION:
#95501
11-1/16"
16-3/4"
18-15/16"
3-3/8"
'22568%67$7,21
9,'(2$8',2
,6&&8
&;
&; &;&; &; &; &; &;
,65&8
00 '
0
0 '
0$67(567$7,21
3$287387
3 3 /3 3 /
&217$&7287387
/ / / /
P
,66&8
0;0;'
' 0;0; ,30; ,3 0;
,3
,6,3&
$OOWKHSRUWVH[FHSW>/$1@DUHQRW
'R127FRQQHFWWR/$1QHWZRUN
IRU/$1QHWZRUN
9,'(2287387
9 9
ȭ㹼ȭ
&+,0(,1387
6(
&217$&7,1387
// 6( 6( 6( %%
675,3/(1*7+
32:(5
P
$&7
67$786
/LQN
0$&$''5(66
ȭ㹼ȭ
/$1
(7+(51(7 '&9
675,3/(1*7+
IS-CCU
How-To
Video Link
Programming Videos

2 | IS Series Local System Programming Guide
For rst time programming, it is recommended to follow Step 1 - Step 11 in order. Refer to the IS Local System Setting
Manual on the CD included with the IS-CCU for complete programming information.
IMPORTANT:
If this IS-CCU will be used with an IS-IPC, please refer to the IS-IP Setting Manual for programming instructions.
Step 1: Change PC Network Settings (optional)
-
Allows the PC to communicate with the IS-CCU.
Step 2: Log in to the IS-CCU
- Entering name and password for the rst time.
Step 3: Change Network Settings (optional)
- Putting the IS-CCU on the network for ease of programming.
Step 4: Change Administrator Settings (optional)
- Creating a new name and password.
Step 5: Register Paging Zones (optional)
- Creating paging zone name(s).
Step 6: Control Unit Composition
- Dening what control units are in the system.
Step 7: Register Stations
- Dening what stations are in the system by assigning station numbers and names.
Step 8: Advanced Station Settings
- Dening which doors/subs call which masters.
Step 9: Zone Setting (optional)
- Dening which stations will be in each paging zone.
Step 10: Time and Date Setting
- Updating the time and date displayed on the master(s).
Step 11: Updating the System
- Uploading all settings to the IS-CCU.
The IS-CCU default IP address is https://192.168.0.30. The PC will need to be set in the same subnet in order to
connect to the IS-CCU.
A. Open Control Panel
- Windows XP® (Classic View) Network Connections Double click Local Area Connection to open
Connection Status window.
- Windows 7® (Category View) Network and Internet View network status and tasks Click
Local Area Connection to open the Local Area Connection Status window.
B. Click the Properties button to open Local Area Connection Properties window.
C. Scroll down and left click Internal Protocol (TCP/IP) then click Properties button to open Internet Protocol
Properties window.
D. Select the Use the following IP address radio button. Type in the IP address 192.168.0.100 (the last number
can be any valid host address except 30) and change the subnet mask to 255.255.255.0. Click [OK].
E. Click [OK] in Connection Properties window to accept these changes.
Step 1: Change Network Settings (optional)
GENERAL OVERVIEW:

3
A. Open a web browser and point the address bar to https://192.168.0.30 and hit Enter.
Note: ensure that https (for security) is being used in the address bar.
B. A security certicate error message will appear. Click “Continue to this website.”
C. Choose preferred language (see Figure 2.1).
D. Log in to the unit using the default administrator ID “aiphone”, and default password “aiphone” (see Figure 2.2).
Figure 2.1: Language Selection Figure 2.2: Log in
E. When System conguration appears, ensure that Local system is checked under (see Figure 2.3). If it is not, check
the Local system radio button and click Temporarily stored to save the setting.
A. Select Network setting from the menu on left.
B. The default option is DHCP. Aiphone recommends assigning a static IP address by
clicking the Static IP Address radio button and entering a unique IP Address and Subnet Mask (see Figure 3.1).
C. Click Temporarily stored to save changes.
Figure 2.3: System Conguration
Figure 3.1: Network Setting
IMPORTANT:
When changes are made while programming, click Temporarily stored to save data prior to leaving
each screen. The saved data will be applied to the system when the system is updated.
Step 2: Log in to IS-CCU
Step 3: Change Network Settings (optional)
Step 1
Video Link
Step 2
Video Link

4 | IS Series Local System Programming Guide
A. Select Administrator setting from the menu on left.
B. The default ID and password are both aiphone. Enter a New administrator ID
and/or New Password if desired (see Figure 4.1).
C. Click Temporarily stored to save changes.
Figure 4.1: Administrator Setting
A. Select Zone registration from the menu on left.
B. Enter a Zone name for each paging zone required (see Figure 5.1). The system can
have up to 99 zones. Each zone can have any combination of masters, rooms, doors, or paging ampliers.
C. Click Temporarily stored to save changes.
Figure 5.1: Zone Registration
A. Select Control units composition from the menu on left.
B. Select which units will be used (see Figure 6.1).
The IS-CCU control unit will support up to 4 IS-RCU and up to 2 IS-SCU.
C. Click Temporarily stored to save changes.
Figure 6.1: Control Units Composition
Step 4: Change Administrator Settings (optional)
Step 5: Register Paging Zones (optional)
Step 6: Control Units Composition
Step 5
Video Link
Step 6
Video Link

5
A. Select Registering stations from the menu on left.
B. The Registering stations table will be populated based on the settings made in Step 6.
Enter a Station number and Station name for each door/sub/master unit. In the
Station type column, use the drop-down list to identify the type of station connected (see Figure 7.1).
C. Click Temporarily stored to save changes.
Figure 7.1: Registering Stations
A. Select Advanced station settings from the menu on left.
B. The Advanced station settings table is populated based on the stations registered in
Step 7 (see Figure 8.1).
D. Click on Called stations.
Figure 8.1: Advanced Station Settings
C. To program door/sub, check box and click on Advanced settings. A new window will open (see Figure
8.2). If multiple units of the same type need to call the same master(s), check appropriate units and click
Advanced settings.
Figure 8.2: Advanced Settings
Step 7: Registering Stations
Step 8: Advanced Station Settings
Step 7
Video Link
Step 8
Video Link

6 | IS Series Local System Programming Guide
E. The master stations programmed to be called will be listed. When programming for the rst time, the list will be
blank. Select the Call priority level from the drop-down list (see Figure 8.3). Click on Reference to open a new
window to select the masters to be called (see Figure 8.4).
Figure 8.3: Advanced Settings - Called Stations
F. Check the box beside the master(s) for the door station to call, then click Close. A maximum of 20 masters can
be chosen for any given door station (see Figure 8.4).
Figure 8.4: Advanced Settings - Called Stations
Figure 8.5: Advanced Settings
Figure 8.6: Advanced Settings
Step 8: Advanced Station Settings (continued)
G. The Advanced settings window will now display the masters that will be called (see Figure 8.5). If a master was
selected in error, check the box next to that master and click Delete to remove it from the list. Once the list is
correct, click Close.
H. Click Other in the Advanced settings window (see Figure 8.2). A new window will open.
I. In the Advanced settings, Video door station, Other window, choose which settings need to be changed from the
default settings. Upon making changes, click Close (see Figure 8.6).

7
J. Close the Advanced settings windows to get back to the main Advanced station settings window.
K. Repeat steps C through J for all video door stations, audio door stations, and room stations.
L. Click Temporarily stored to save changes.
A. Select Zone setting from the menu on left.
B. Select the Zone number from drop-down list (see Figure 9.1), then click Reference
.
A new window will appear.
Figure 9.2: Stations to Add to Zone
C. Check the box beside each station to add to the selected zone (see Figure 9.2).
D. Click Close .
Step 8: Advanced Station Settings (continued)
Step 9: Zone Setting (optional)
IMPORTANT:
If connecting an 8Ω speaker to the IS-RS room station, click on the Other button and select External speaker
from the new window. If the scan monitor function is required for a master, select the master(s) and click on
Advanced settings to program this feature.
Figure 9.1: Advanced Settings
IMPORTANT:
If a paging amplier is to be included in a zone, click the Reference button to the right of PA output and select the
paging output to be included. The PA output must have been named in Registering Stations (Step 7) to be shown in
this list.
Step 10
Video Link

A. Click the Time and date setting from the menu on left.
B. If the PC’s date and time is correct, click the
Synchronized with PC
button. If not,
set it manually (see Figure 10.1).
C. Click Temporarily stored to save changes.
E. The Zone setting window should now show the stations selected from the list (see Figure 9.1). Repeat process for
remaining zones.
C. Click Temporarily stored to save changes.
Figure 9.1: Zone Settings Populated
A. Click Updating the system from the menu on left.
B. Click Update to save all data to the IS-CCU. The system will reboot and return
to the language selection screen when complete.
Depending on the amount of data and changes, the reboot could take as long as 5-10 minutes.
Figure 10.1: Time and Date Setting
Step 9: Zone Setting (continued)
Step 10: Time and Date Setting
Step 11: Updating the System
Aiphone Corporation
1700 130th Ave. NE Bellevue, WA 98005
Ph: [phone] Fax: [phone]
www.aiphone.com [email protected]
0313 #95501
8| IS Series Local System Programming Guide
Step 11
Video Link
Step 18
Video Link