Aiphone GH SERIES 410 User manual

0410
GH SERIES
QuikStart Installation Guide
Apartment Intercom System
ABBREVIATED INSTALLATION & OPERATION MANUAL
ATTENTION:
- 1 -
This is an abbreviated Installation Manual, addressing Wiring and Programming of the GH System only.
The complete GH System Installation and Operation Manual is located on the CD that comes with the
GH-BC Bus Control Unit. Access the PDF file from the CD and print the entire manual if a hard copy is
needed. If installing a digital entry system, the program for loading names and numbers for each tenant
is also located on the CD.

GH Series Installation Manual Supplement
1. Turn the power switch on the GH-BC to the ON position.
2. At the Entrance Panel, loosen the screw on the bottom of the front frame
using the supplied #10 spanner tool (part # 262230) and remove the front
panel. (Note: a #10 spanner bit is available at most hardware stores.)
3. To put the system into program mode, lift the rubber cap on the GH-DA/A
and press and release the program button using a long thin tool, such
as a small screw driver. The In-Use LED will blink for approximately 6-15
seconds, then remain lit solid.
4. After the In-Use LED is lit solid, press and release the talk button on the
first tenant station. You should have hands-free communication between
the tenant and the entry at this point. If programming a video system,
should also have the video image from the entrance station.
5. For the GH -SW,press and release the button you wish to assign to the
tenant you arein communicationwith. (If you press and hold until you hear the
beep tone, you have just cleared the station. Press and release quickly; you will
hear a short blip tone upon releasing. This indicates that the unit has been
programmed correctly.)
Forthe GH-NS, scroll to the residentname and number you wish to assign
then press and release the bell (call) butto n. A short blip tone will be
emitted at the entry panel indicating a successful program for that tenant.
See bullet point below if more than one blip is heard.
6. Press the talk button again on the tenant station to turn that unit off. If this
is your first time programming the system, it is recommended to exit
programming and test the station that you just programmed. Press the
program button on the GH-DA/A once to exit programming and the LED
will go off. You should now be able to call the tenant you just programmed.
If it works, re-enter program mode and repeat the previous steps to
program the remaining tenant stations in the system.
Programming Guide for Assigning Tenant Station ID Numbers
Ensure that all units are installed and wired properly. If your system includes the GH-NS name scroll
module, program the resident information (tenant names and room numbers) before assigning the ID’s.
7. If there is more than one tenant station in a unit, each station will have to be assigned to the entry
panel using the procedure above. The entry panel will emit 2 blip tones for the second unit, 3 blip
tones for the third unit,and 4 blip tones for the fourth unit that is programmed for entry from the panel.
5 blip tones indicates a programming error. If 5 blip tones are heard, you’ll need to clear the program
for the tenant and entry panel address. See page 3.
IMPORTANT:
Follow these instructions carefully when programming the GH entrance panel to call tenant stations.
0210
- 2 -

1. Put the system into programming mode using the procedure
described on page 1, step 3.
2. At the tenant station, press and hold the door release button and bell
button simultaneously until a beep is emitted from the unit (should
take about 3 seconds ). The internal memory is now cleared.
3. If using the GH-SW, press and hold the call button that you wish to
clear until you hear a continuous beep. If using the GH-NS, display
the resident info on the screen that you wish to clear, then press and
hold the bell button(call button) until you hear a continuous beep.
That address in the entry panel is now cleared.
4. You can now re-program the tenant
station(s) using the procedure on page 1.
Programming multiple entrance stations / Concierge stations via Link Data:
Correcting or changing an ID setting:
In order tocorrect a programming error, the entrance station(s) and the tenant station(s) must be cleared of
their incorrect program data, then programmed again correctly. Follow these steps to clear:
If your system has more than one entrance panel and/or you’re using the GH-NS module or GH-MK
Concierge station, you can send all of the tenant ID’s you just programmed to the other units using the Link
Data feature. This can be done manually via the keypad on the entry panel or via the supplied software.
Using the keypad
and scroll module: Using the supplied software:
1. Import the data from the GH-NS that
you’ve set the ID’s on into the software
with the LinkData box checked.
2. Export the data you just imported to
each of your other GH-NS modules
with the LinkData box checked.
Note: The GH-MK can be used to manually transfer data to other GH-MK’s or GH-NS’s in the system.
- 3 -

- 4 -
= PS-2420UL

- 5 -

- 6 -
= PS-2420UL

- 7 -
Please refer to the GH installation manual for complete wiring
information on GH Expanded system.

- 8 -

- 9 -

- 10 -

- 11 -

- 12 -

- 13 -

- 14 -
= PS-2420UL
= PS-2420UL

- 15 -

- 16 -

- 17 -

- 18 -

- 19 -

- 20 -