Aiphone IX-MV User manual

IX SYSTEM
IP Network-Compatible System
Quick Start Programming Guide
IX System
IP network-compatible intercom
Video Door Station (IX-DA)
Audio Only Door Station (IX-BA)
Web Setting Manual
Software version 2.00 or later
Important
y
y
Begininstallation after reading and understanding the procedures for system
configuration.
y
y
Thesetting data should be backed up and stored in a safelocation after configuration is
complete.
Theillustrations and images in this manual may vary from the actual ones.
Beforeconfiguring and using the system, read Setting Manual and Operation Manu al (PDF)caref ully.
*Forthe installation and connection of each device, refer to Installation Manual.
IX System
IP network-compatible intercom
Master Station (IX-MV)
Web Setting Manual
Software version 2.00 or later
Important
y
y
Begininstallation after reading and understanding the procedures for system
configuration.
y
y
Thesetting data should be backed up and stored in a safelocation after configuration is
complete.
Theillustrations and images in this manual may vary from the actual ones.
Beforeconfiguring and using the system, read Setting Manual and Operation Manu al (PDF)caref ully.
*Forthe installation and connection of each device, refer to Installation Manual.
IX System
IP network-compatible intercom
IX Support Tool
Setting Manual
Software version 2.0.0.0 or later
Important
y
y
Begininstallation after reading and understanding the procedures for system
configuration.
y
y
Thesetting data should be backed up and stored in a safelocation after configuration is
complete.
Theillustrations and images in this manual may vary from the actual ones.
Beforeconfiguring and using the system, read Setting Manual and Operation Manu al (PDF)caref ully.
*Forthe installation and connection of each device, refer to Installation Manual.
This is an abbreviated programming manual, addressing basic program settings for an IX System using the
IX Support Tool. A complete set of instructions (IX Web Setting Manual / IX Operation Manual / IX Support Tool Setting Manual)
can be found on the DVD-ROM provided with the IX-MV Master Station.
ATTENTION:
IX-BA IX-DA
SETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY LIST
IX-MV IX-DAIX-BA
FK2128 A 1114 SQ

2 | IX Quick Start Programming Guide
For basic system programming, all steps are REQUIRED unless marked OPTIONAL. Refer to the IX Support Tool Setting
Manual on the DVD-ROM included with the IX-MV for complete programming information.
Step 1: Change PC Network Settings (OPTIONAL)
- Allows the PC to communicate with the Door Stations and Master Stations.
Step 2: Opening IX Support Tool
- Open program, define size of system, and name of system.
Step 3: Station Information - Customizing Station Numbers and Names (OPTIONAL)
- Create unique station numbers and names.
Step 4: Network Settings
- Assign IP address (batch).
(Refer to the IX Support Tool Setting Manual when using an IPv6 network)
Step 5: Association Settings
-Link station settings to stations found in Search.
Step 6: System Information - Address Book “Master Station” (OPTIONAL)
- Add or remove stations from the Address Book.
Step 7: Call Settings - for Door Stations
- Select called station, call level, and broadcast method.
Step 8: Setting the Time
- Manually enter time or sync time with PC.
Step 9: Updating the System
- Uploading setting file to stations (batch).
The Door Station and Master Station’s default IP address is https://192.168.1.160. The PC will need to be set in the same
subnet in order to connect to the Door Stations and Master Stations.
A. Open Control Panel
- Windows XP (Classic View) Network Connections Double click Local Area Connection to open
Connection Status window.
- Windows 7 (Category View) Network and Internet View network status and tasks Click
Local Area Connection to open the Local Area Connection Status window.
B. Click the Properties button to open Local Area Connection Properties window.
C. Scroll down and left click Internet Protocol (TCP/IP) then click Properties button to open Internet Protocol Properties
window.
D. Select the Use the following IP address radio button. Type in the IP address 192.168.1.100 (the last number can be
any valid host address except 160) and change the subnet mask to 255.255.255.0. Click [OK].
E. Click [OK] in Connection Properties window to accept these changes.
Step 1: Change Network Settings (OPTIONAL)
Step 2.1 Connect all IX stations and the programming PC to the same network.
Step 2.2 Install the IX Support Tool on the programming PC.
Step 2.3 Open the IX Support Tool.
Step 2.4 Log in. Default Settings:
Step 2: Opening IX Support Tool
ID: admin
Password: admin
GENERAL OVERVIEW:

3
Step 2.5 The New System screen will appear (Figure 2-B).
Enter in quantity of:
Master Stations
Video Door Stations
Audio Only Door stations
System Name
Step 2.6 Select appropriate radio button for door release.
Figure 2-B: New System Screen
Figure 3-A: Customizing Numbers and Names
Figure 2-C: Table View with default names
Step 2: Open IX Support Tool (continued)
Step 2.7 The IX Support Tool Settings Table View will be displayed with default station numbers and station names
(Figure 2-C). To customize, proceed to Step 3.
Step 3: Station Information - Customizing Station Numbers and Names (OPTIONAL)
Step 3.1 Select Number cell to be changed. Selection will turn orange.
-Enter custom number (3-5 digits) Edit will turn pink.
Step 3.2 Select Name cell to be changed. Selection will turn orange.
-Enter custom name (no special characters allowed) Edit will turn pink .
Step 3.3 Click to save changes.
Step 2.6
Step 2.5
Step 3.1 Step 3.2
Step 3.3
Default Names
Default Numbers
Name (furigana) is only accessible when
using Japanese or Chinese language.
Note:
Location is only accessible after the
Location Registry has been filled out.
Note:

4 | IX Quick Start Programming Guide
Step 4: Network Settings
Step 4.1 From menu on left, under Network Settings, select IP Address.
- Click on
Batch IP Address Configuration
.
Step 4.2 Enter starting IP Address, and Subnet Mask (see Figure 4-A).
Step 4.3 Select All from the Select Station(s) by type drop-down menu to apply IP Address and Subnet Mask to all stations.
- Click .
- Click .
Step 4.4 A pop-up will occur asking Select Station’s IP Address will be batch configured. Continue? (see Figure 4-B).
- Click .
Step 4.5 Click on the main page to save changes.
Figure 4-A: Batch IP Address Configuration
Step 5.1 From the Tools(T) drop-down menu, select Association Settings (see Figure 5-A).
Step 5: Association Settings
Figure 5-A: Association Settings
Figure 4-B: Continue?
Step 4.4
Step 4.2
Step 5.1
Step 4.3
Enter the IP address and subnet
mask individually when not
using the Batch IP Address
Configuration.
Note:

5
Step 5: Association Settings (continued)
Figure 5-B: Association Setting Window (Station Settings List / Station List)
Figure 5-C: Association Setting Window (Associated Stations List)
Stations that have been associated will appear in the Associated Stations List (bottom window).
Repeat steps above until all stations have been associated (see Figure 5-C).
Step 5.5 Click to save changes.
When the Association Setting window appears:
Step 5.2 Select a station from the Station Settings List (upper window).
Step 5.3 Select a station from the Station List (middle window).
Step 5.4 Once both have been selected, click (see Figure 5-B).
Step 5.5
Step 5.2
Step 5.3
Step 5.4
Ensure the same Type of
station is being selected from
each list. For example, both
should be Master Stations or both
should be Audio Only Door Stations.
Note:
Stations will reboot after being associated.
This could take up to 10 minutes.
Note:

6 | IX Quick Start Programming Guide
Step 6: System Information - Address Book “Master Station” (Optional)
Step 6.1 From menu on left, under System Information, select Address Book (see Figure 6-A).
Step 6.2 Click to view the Address Book.
Figure 6-A: Address Book
Figure 6-B Address Book
Step 7.1 From menu on left, under Call Settings,
select Called Stations (for Door
Stations) (see Figure 7-A).
Step 7.2 In the Call Settings column,
select the call-in level.
Normal = low level
Priority = mid level
Urgent = high level
Step 7.3 Click .
Step 7.4 When Save changes? pop-up appears,
(see Figure 7-B), click .
Step 7: Call Settings (for Door Stations)
Figure 7-A: Call Settings window
Figure 7-B: Save Changes? window
Step 6.3 To Remove or add stations to an Address Book (see Figure 6-B).
- In the Available Stations list, select appropriate icon from drop-down menu
“ “= Display in address book , “ “(blank space) = Do not display in address book.
- Changed stations will turn pink.
Step 6.4 Click to save changes.
Step 6.4
Step 7.2
Figure
Step 7.4
Step 6.2
Step 6.3
Step 6.1
Step 7.1
Step 7.3
By default, all stations will be listed in
each address book.
Each address book can hold a
maximum of 500 stations.
Note:

7
Figure 7-C: Open Call List window
Step 7: Call Settings (continued)
Step 8: Setting the Time
Step 8.1 From menu on left, under Station Information, select Time (see Figure 8.1).
Step 8.2 In the Select time zone column, select the appropriate time zone from the drop-down menu.
Changes will be shown in pink.
Step 8.3 Click .
Step 8.4 When pop-up appears asking to Save changes, click .
Figure 8-A: Time Zone window
Step 7.4 In the Open Called Station List (see Figure 7-C), select call method from drop-down menu.
U = Unicast
M = Multicast
Blank space = No call or not call (blank space)
Changes will be shown in pink.
Step 7.5 Click to save changes.
Step 7.4
Step 7.5
Step 8.1
Step 8.2
Step 8.3

8 | IX Quick Start Programming Guide
AIPHONE CO.,LTD., NAGOYA, JAPAN
http://www.aiphone.net/
Issue Date: Nov. 2014 Printed in Thailand
Step 9: Updating the System
Step 9.1 From the File(F) drop-down menu, select Upload Settings To Station. (see Figure 9-A).
Figure 9-A: Upload Settings To Station
Figure 9-C: Upload StatusFigure 9-B: Upload Settings To Station
Step 9.1
Step 9.3
Step 9.2
Step 9.4
Step 9.2 Use the Select stations(s) by type drop-down menu to select all stations or stations by type.
Step 9.3 Click (see Figure 9-B).
Step 9.4 When stations have been selected (checkmark displayed in the Select column) click (see Figure 9-B).
Step 9.5 The status of the upload will be displayed for each station in the Status column displaying either Success or Failed
( see Figure 9-C ).
Step 8.5 In the Manual Date / Time Setup window:
- Enter in current date and time.
or
- Click
.
Step 8.6 Then click (see Figure 8-B).
Figure 8-B: Manual Date / Time Setup
Step 8.7
Step 8: Setting the Time (continued)
Step 8.7 When Time setting updated pop-up appears, click .
Step 8.6
Step 8.5