Aiphone Ixg-2c7 User manual

IXG-2C7, IXG-2C7-L (Tenant Station)

Issue Date Mar. 2020 FK2530 A P0320 RQ 60259

Introduction

• Read this manual before installation and connection.

Read the "Setting Manual" and "Operation Manual". The manuals can be downloaded from our

homepage at "https://www.aiphone.net/support/software-document/" free of charge.

• After completing installation and connection, program the system according to the “Setting Manual”.

The system cannot operate unless it is programmed.

• After performing installation, review with the customer how to operate system.

Perform installation and connection only after gaining sufficient understanding of the

system and this manual.

Literature information

The important information concerning correct operation and what you should observe is marked with

the following symbols.

Indicates that users may require caution (including warning / caution).

Alerts users to prohibited actions.

Restricts user actions / provides instructions.

Tips and additional information for operation.

Example of System Configuration

LAN

IXG-DM7 (-HID)IXG-2C7 (-L)

IXGW-GWIXGW-LC

IX-MV7-HB

IXG-MK PC (third party)

PoE switch

(third party)

Network Camera

(third party)

PoE switch

(third party)

PoE switch

(third party)

PoE switch

(third party)

PoE switch

(third party)

PoE switch

(third party)

PoE switch

(third party)

IX-DV

Status Indicator

Refer to "IXG-2C7(-L) Operation Manual" for additional indicators not listed below.

: Lit : Off

Status (pattern) Description

Blue

flashing

0.75 sec0.75 sec Booting

0.5 sec4sec Communication

failure

sec

0.25

sec

0.25

sec

0.25

sec

0.25

sec

0.25

sec

Firmware version

updating

Blue light Standby (Depends

on setting)

Part Names and Accessories

IXG-2C7, IXG-2C7-L

LAN(PoE) port

Option connector terminal

microSDTM card slot

Back view

Front view

Hearing aid T-mode

compatibility symbol

(IXG-2C7-L only)

Status indicator (Blue)

Microphone

SpeakerSpeaker

Touchscreen LCD

(hearing aid-compatible)

Mounting

bracket ×1

(attached to the station)

Installation

Manual ×1

(this manual)

Download

guide ×1

Option

connector ×2

(10 pin ×1, 4 pin ×1)

Cable tie ×1

Included accessories

MAC address

Chinese RoHS

declaration ×1

(IXG-2C7 only)

Choose a microSD card (sold separately) using the recommended specifications below (these are

referred to collectively as "microSD cards").

Standard Supported storage

capacity Format Speed class

microSDHC memory

cards

4 GB to 32 GB FAT32 SD speed class 10

• A microSD card is not included with this station.

• Some microSD cards may not operate properly.

• If the card contains data other than video/audio files, it may not have enough space to record video/

audio recordings.

• The network camera may not be able to record video, depending on the size of the video.

• A maximum of 999 video/audio files can be saved. However, this may vary depending on the size of the

video/audio files and the capacity of the microSD card.

• Aiphone is not to be held responsible in any way for microSD cards.

Precautions

Warning Negligence could result in death or serious injury.

Do not disassemble or modify the

station.

This may result in fire or electrical

shock.

Do not connect any terminals on

the station directly to an AC

power line.

This may result in fire or electrical

shock.

Do not, under any circumstances,

open the station.

Voltage within some internal

components may cause electrical

shock.

Caution Negligence could result in injury to people or damage to

property.

Do not install or connect the

station with the power on.

This may result in electrical shock or

malfunction.

Make sure the wiring is correct

and there are no wiring shorts

before switching on the station.

This may result in fire or electrical

shock.

Install in a place where the station

will not get easily bumped.

This may result in injury.

Do not put your ear close to the

speaker when using the station.

May cause harm to the ear if a

sudden loud noise is emitted.

About microSD card

Installation Manual

General Precautions

• Install low-voltage lines at least 30cm (12") away from high-voltage lines (AC100V - 240V), especially inverter

air conditioner wiring. This may result in interference or malfunction.

Notice

• The illustrations used in this manual may differ from the actual product.

• If the station is used in areas where there are business-use wireless devices such as a transceiver or mobile

phones, it may cause malfunction.

• If the station is installed in an area with an extremely strong electrical field, such as in the vicinity of a

broadcasting station, it may create interference and cause malfunction.

Precautions for mounting

• Installing the device in the following locations could cause malfunction:

-Locations under direct sunlight

-Locations near heating equipment

-Locations subject to liquid, iron filings, dust, oil, or chemicals

-Locations subject to moisture and humidity extremes

-Locations where the temperature is quite low

-Locations subject to steam or oil smoke

-Sulphurous environments

-Locations close to the sea or directly exposed to sea breeze

• If existing wiring is used, the device may not operate properly. In that case, it will be necessary to replace the

wiring.

• Do not use an impact driver to fasten screws. Doing so may cause damage to the device.

• Avoid installing the station in concave space of a wall to prevent disconnection of communication.

• This unit is designed for indoor use only. Do not install at outdoor location.

How to Install

When Flush mount kit is used, refer to the "How to Install" IXG-FMK-2C7 Installation Manual.

Installation of Tenant Station

Remove the mounting bracket.

Slide the mounting bracket down and remove it.

Station

Tab

Mounting bracket

Slide down

Slot

Mounting bracket Tabs (4 locations)

Slots (4 locations)

[Back]

Insert a microSD card into the microSD card slot if

recording function is used.

* If microSD card is not needed, go to step 3.

[Back]

microSD card slot

(1) Pull the microSD card slot cover to open.

(2) Insert a microSD card.

*Push it in until you hear it click into place.

*When you take the microSD card out, push the microSD card until

you hear it click, and then remove it.

(3) Return the cover.

Station

Attach the station to the mounting

bracket.

Mounting screws x 4 (not included)

(Screw Shaft: Φ4.1 or less)

(Slotted head: Φ8.2 or less, 3.0mm or less in height)

Conect the option connector (included) to the low-voltage

lines using crimping method, then insert the option

connector and Cat-5e/6 cable to the station.

Low -voltage lines

Cat-5e/6 cable

Recommended

Mounting height

(center of gang box)

1,500mm (4' 11'')

3-gang box

Attach the mounting bracket.

Mounting bracket (included)

Option connectors

(included)

Fasten Cat-5e/6 cable to

the station with the cable

tie (included).

Cable tie

Cat-5e/6 cable

Be sure to

fasten Cat-5e/6

cable to prevent

from coming

out.

How to Connect

Connection Precautions

■Cat-5e/6 cable

• For connection between devices, use a straight-through cable.

• If necessary, when bending the cable, please observe the manufacturer’s recommendations. Failure to do so could cause a communication failure.

• Do not strip away the cable insulation any more than is necessary.

• Perform termination in accordance with TIA/EIA-568A or 568B.

• Before connecting the cable, be sure to verify conduction using a LAN checker or similar tool.

• A RJ45 covered connector cannot be connected to the LAN ports of the stations. Use cables without covers on the connectors.

• Be careful not to pull on the cable or subject it to excessive stress.

■Precautions regarding low-voltage line

• Use PE (polyethylene)-insulated PVC jacketed cable. Parallel or jacketed conductors, mid-capacitance, non-shielded cable is recommended.

• Never use twisted-pair cable or coaxial cable.

• 2Pr quad V twisted pair cables cannot be used.

Coaxial cableParallel cable

• When connecting low-voltage lines, perform the connection using either the crimp sleeve method or soldering, then insulate the connection with electrical

tape.

Crimp terminal

Solid

wire

Stranded

wire

Solid

wire

Stranded

wire

Electrical tape

Soldering

Electrical tape

1. Line up the solid wire

and stranded wire and

crimp them together.

2. Overlap the tape by at

least a half width and

wrap the connection at

least twice.

1. Twist the stranded

wire around the solid

wire at least 3 times.

2. After bending down

the point, perform

soldering, with care that

no wires protrude from

the soldering.

3. Overlap the tape by

at least a half width

and wrap the

connection at least

twice.

Crimp sleeve method Soldering method

-If the connector-attached lead wire is too short, extend the lead with an intermediate connection.

-As the connector has polarity, perform the connection correctly. If the polarity is incorrect, the device will not operate.

-When using the crimp sleeve method, if the end of the connector-attached lead wire has been soldered, first cut off the soldered part and then perform crimp.

-After completing connection of wires, check that there are no breaks or inadequate connections. When connecting low-voltage lines in particular,

perform the connection using either soldering or the crimp sleeve method and then insulate the connection with electrical tape. For optimal

performance, keep the number of wiring connections to a minimum.

Simply twisting low-voltage lines together will create poor contact or will lead to oxidization of the surface of the low-voltage lines over long-term use, causing poor

contact and resulting in the device malfunctioning or failure.

Soldering method Crimp sleeve

method

Wiring Connection

• Insulate and secure unused low-voltage lines and the connector-attached lead wire.

RYC2-

RYC2+

RYC1-

RYC1+

Purple

Green

Blue