Aiphone JP-DVF-RP10 User manual

JP-DVF-RP10
Vandal Resistant Color Video Door Station
with Built in HID®multiCLASS SE®Card Reader
-INSTRUCTIONS-
The JP-DVF-RP10 is a JP Series color video door station with a multiCLASS SE®card reader built
onto the same stainless steel faceplate. The card reader provides electronic access to a building
through a separate Access Control System, which is not supplied by Aiphone.
NAMES & FUNCTIONS:
1. Camera 5. Directory card
2. Microphone 6. Call button
3. LED illuminator 7. multiCLASS reader
4. Speaker
FEATURES:
• All-in-one solution - Communication product &
card reader
• If a card is missing or malfunctioning, audio/video
communication can provide user verication
• Standard Wiegand output to access panel
• Convenience of installing combined components
JP-DVF-RP10
OPTIONAL ACCESSORIES:
• SBX-ISDVFRA - Surface mount stainless steel
backbox
INSTALLATION:
• For ush mounting, cut a hole in the wall and use
supplied back box.
Box dimensions are:
11-1/16” H x 5-13/16” W x 1-3/4” D
• For surface mounting, use the SBX-ISDVFRA
surface mount box. This box can mount to a
standard 1-gang box or to any at surface.
PACKAGE CONTENTS:
JP-DVF-RP10
Vandal-resistant Door Station
Security Driver
Blank name
placard
Back box
& tamper-resistant screws
1
2
3
4
5
6
7

WIRING DIAGRAM:
1A1
1A2
2A1
2A2
3A1
3A2
4A1
4A2
+
-
A1
A2
+
-
JP-DVF-RP10 JP-4MED
PS-2420UL
TESTING & OPERATION:
• When power is applied to the card reader, the LED will ash green three (3) times while the
beeper beeps simultaneously. The LED will then turn red. This indicates that the microcontroller is
operating properly.
• Present an ID card to the reader (hold card directly in front of reader). The LED will momentarily
turn green while the beeper beeps once, indicating that the card was read successfully.
SPECIFICATIONS:
CARD READER:
Reader type: RP10
Power Source: 5 ~ 16V DC
Current: 75mA (Avg); 200mA (peak)
Terminations: Color-coded pre-wired pigtail
Wiring Distance: 500’
Operating Temp: -31° ~ 150°F / -35° ~ 65°C
Operating Humidity: 0-95% relative humidity
non-condensing
CAMERA:
Camera unit: CMOS camera
Scanning line: 525 lines
Min. illumination: 5 Lux at 1’6”
Terminations: Screw terminals
Operating Temp: 14° ~ 140°F / -10° ~ 60°C
Wiring Distance: 330’ w/ 871802 wire
Dimensions: 11-11/16” H x 7” W
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
• For proper regulatory compliance, the drain wire should be disconnected at the power
supply end of the cable.
• Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• The Reader is intended to be powered from a limited power source output of a
previously certifed power supply
Aiphone Corporation |www.aiphone.com/home | [email protected]m |P: 800.692.0200
Pg. 2
JP-DVF-RP10 Instr.
0715
Pigtail Discription
Yellow Beeper Input
Orange Green (GRN) LED Input
Black Ground (RTN)
Red +VDC
Drain Unused
Brown Red LED Input
Blue Hold Input
Connect the reader to the host according to the
wiring table below and the host installation guide.
Pigtail Discription
Red/Grn GPIO1 (RS232-T/RS485-A)
Tan GPIO2 (RS232-R/RS485-B)
Violet Open Collector Output
White Wiegand Data 1 / Clock
Green Wiegand Data 0 / Data
Pink GPIO3 (RS485-Z)
Gray GPIO4 (RS485-Y)