Aiphone KBW-M User manual

- INSTRUCTIONS -
The KBW-M adaptor converts a standard CCTV camera's signal to a 2-wire signal, compatible with the
KB 3x5 Color Video system. This allows the utilization of a color camera on a video input on the KB
system, viewable from any monitor in the system. (A camera and KBW-M can be added to any input
that is not used by a KB-DAR video door station.)
KBW-M
Video Modulator for the KB Series Color Video System
KBW-M TERMINAL DEFINITIONS:
BNC Connector: Coax input from CCTV camera
A1 2-Wire output to
A2 KB-3MRD
MD Input from motion detector
MD (with normally open contacts)
Special
Order
Products
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
1A1
1A2
2A1
2A2
3A1
3A2
B1
B2
+
-
KB-3MRD
KB-DAR
A1
A2
A1
A2
BNC
Cnctr
MD
MD
KBW-M
PS-2420UL
+
-
Pg. 1
KB-DAR
A1
A2
NOTES:
1. In this system example, the CCTV camera
is on input #3. Cameras are viewed by
pressing the MONITOR button (on any
monitor.) Press once to turn on camera 1
(KB-DAR), press again to switch to camera 2
(KB-DAR #2). Pressing MONITOR a third
time will switch to Camera 3 (CCTV), and a
fourth time turns the monitor off.
2. OPTIONAL: An input for a motion detector
is provided to activate the CCTV camera.
The Monitor will turn on and a chime will be
heard. The monitor will stay on for
approximately 30 seconds.
KBW-M
Motion Detector*
Non-Polarized
WIRING DIAGRAM: KBW-M Modulator for Standard CCTV camera
(Optional)
Non-Polarized
Non-Polarized
Camera
input
Output to
KB-3MRD
Input from Motion
Detector
* Or any signaling
device that provides a
normally open
momentary dry closure.
Motion Detectors with N/O Contacts:
Detection Systems DS720I
Pulnix 6612
Intellisense 8140S
Ademco 1998PI
Sentrol AP750

Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
[phone]
FAX [phone]
Toll Free Technical Support:
1-800-692-0200
FAX: [phone]
E-mail [email protected]
Pg. 2
KBW-M Instr.
0703bkjs
OPERATIONS
Activation of a camera from a Monitor:
1. The CCTV camera can be viewed on any of the KB monitors in the system by pressing the MONITOR button.
2. The video door stations and/or camera(s) will come up sequentially based on the inputs that they are on. (One
press of MONITOR button brings up camera 1, second press brings up camera 2, third press brings up
camera 3.)
3. After the last camera in the system is activated, the next press of the MONITOR button will turn off the
monitor. If the monitor is left on, it will automatically time out after approximately 30 seconds.
Activation of a camera by the motion detector: (Optional feature)
Any motion detector with a normally open contact can be connected to the KBW-M to activate the CCTV camera.
1. When the motion detector is tripped, the camera will turn on and be viewed on all KB monitors in the system.
2. A chime will be heard, and the appropriate LED will be lit on the monitor(s).
Door 1: 4-Stroke Chime and LED #1
Door 2: 2-Stroke Chime and LED #2
Door 3: 8-Stroke Chime and LED #3
3. The camera will automatically turn off in 30 seconds.
SPECIFICATIONS:
Power: Supplied by KB-3MRD
CCTV Camera input: 1V Peak-to-Peak at KBW-M
Connector: BNC Connector
Wire: Aiphone wire #871802
18AWG, 2-conductor solid, non-shielded, FPLR type
Wiring distance: (With Aiphone # 871802 wire)
Max. 650' from KBW-M to KB-3MRD
Dimensions: 5-1/2"H x 3"W x 1-1/2"D
Note:
Only information pertaining to the connection and operation
of the KBW-M and connection of a color CCTV camera is
included here. For complete installation, wiring, and
operational information about the KB system, please refer
to the KB-3MRD Installation Manual.