Do
not disassemble
or alter.
Do
not disassembleor alter
this
equipment. Doing
so
would be
dangerous. Fire or electric shock
couldresult.
Wall gasket
\
Electric shock caution
Do not touch the main unit with
damp or wet hands.Electric shock
and equipmentdamagecould
result.When existingchimewiring
is used, it is possiblethat itcontains
AC power.
This
can cause
equipmentdamage and electric
shock. Have the installation done
by an electricalcontractor,low
voltage contractor,or qualified
personnel.
A
4ny place too closeto a source
If electricalnoise,for example a
xoadcastingstation or wireless
stationof any kind.
Any place where the detection
area or cameraangle of view will
be blocked
off.
0305
@
Accessories
Installationmanual(thisdocument)
x
1
Sensordetection area adjustmentsheet
x
1
Manualfor adjusting sensor detection area
x
1
Mountingscrews
x
2
W
Precautionnotation
This
installationmanual uses various symbols for the sake of safeusage.
The results that can occur from ignoringthese indications and handling
this
equipmentincorrectly are categorizedas follows.
*Nopower is being supplied fromthe
masterstation. Wire the master station correctlyto supply power.
Thewiringis incorrect or a lineis open or
shorted. Wire correctly. (See "MOUNTING
AND
CONNECTION".)
DThe unit does
not operate. 'The unit was wired to the master station
with power supplied. Keep the power
OFF
until thewiringis completed.
Icondisplay example
@
symbolindicates a prohibition.The specific content
prohibitedis drawn in or near the figure. (For the figure
on
theleft,disassemblyis prohibited.)
@
symbolindicates behaviorthat is mandatory and gives
Q
directions. Themaster station select switch setting is
reversed. Set "A" and "B"correctly. (See "SETTINGS".)
Whenyou open up
the
package,make sure
all
the accessoriesare present.
JDW-C
The detection area is not correctlyset. .Check the detection area and cameraangle of view area and install
so
that
people are detected. (See ''ADJUSTMENTS''.)
This
indicates that ignoringthe contents of
thewarning and handlingthe equipment
injury.
AwA
R
N
I
N
G
incorrectlycan result in death or severe
This indicatesthat ignoring the contentsof
the waming andhandlingthe equipment
ACAUTION
incorrectlycan result in personalinjury
ndordamageto equipment. People arepassingnearly directlyunder
the sensorcamera. Adjust the upldown angleto point down
so
that they aredetected.
.This
is not a breakdownt.Becauseof the characteristicsof a heat ray type
sensor, it may have difficulty detectingpeople coming directly at the camera.
As much as possible,install in such a way that people cut acrossthe detection
area. (See "ADJUSTMENTS".)
This
productis weatherresistant,
but donot install it in a bathing
room or other place with extremely
high humidity, any place where
Do not spray water directly
on
this
equipment,for examplewith a hose.
Fire, electric shock, and equipment
damagecould result.
water might get into it, or in water.
Peopleare coming directly at the camera.
Use in areaswith water
or highhumidityis
prohibited. BThe systemdoes
not detect
people.
*Connectan externalsensorin
"OR
mode"
so
thatpeople cut across the
detection area. (See "SETTINGS".)
ur"t
This
is not a breakdown. A heat ray type sensorcannot detect objectsthrough
glass.Installin a place where the detectionarea is not cut
off
by the glass.
(See "MOUNTING
AND
CONNECTION".)
Thedetectionareais cut
off
by glass.
This
is not a breakdown. Setthe detectionarea foreach sensor
so
that people
aredetectedby both sensors. (See"SETTINGS".)
With the externalsensor input function in
"AND
mode",people areonly detected
by themain sensor or by the external
sensorbut not by both.
*
The internal sensor switchis
"OFF".
Install securelyto a solid location
so
that the equipmentcan not drop
fromits
own
weight. Equipment
fallingcouldresultin injury.
Q
Installsecurely. Switch "ON" the internal sensor switch.
The speakerselect switchis
"OFF".
Switch "ON"the speakerselect switch.
Main unitcover
Camerawindow
-A
CAUTION
-1
@Sound cannotbe
heard fromthe
unit. 'The masterstation select switchis "B" -Switch the master station select switchto "A". (Sound cannotbe heard from
the unit when the master stationis JA-2MECD or JA-2MCD.)
r
Becareful
not
to
soilor
damage.
1
Thewiringis incorrect or a lineis open or
shorted. Wire correctly. (See "M0U"G AND CONNECTION".)
Notice
This
productdetects a person, provides notice, and shootsimages. It is not an anti-theft device.
Aiphone does not bear responsibilityfor any damage incurred in the event of theft or other suchincident.
@Sound cannotbe
heard fromthe
masterstation. The mic. sensitivityvolume is at the
"Low" side.
Turn
the mic. sensitivityvolume to the "High' side. (See "SE'ITINGS".)
The sensor camerais installed too close
to the master station.
This
is not a breakdown. Install the sensor camerafarther from the master
station or turn themic. sensitivityvolume to the "Low"side until there is
no
howling.
Sensor
\I
4
display window
rA
Do
not touch
the sensor
or
the reflectwe
7
Operation
!
CAUTION
@There is
howling.
1
mirror.
I
I
Thereis a dog or cat or other small
animalin the detectionarea. Set the sensorsensitivity switchto
"L
(Low)". (See "SETTINGS".)
-
InstallationprecautionsA
H
For correct installation
Do
not installin the following places.
Recommend to connect an externalsensor and use it in
"AND
mode".
(See
"SETTINGS'.)
@The sensor is
detectingbut
the detected
objectsare not
displayed
on
the
screen.
Thereis somethingthat moves in the
detectionarea, for examplea flag or
tree
blowing inthe wind, or there are sudden
temperaturechanges.
Setthe sensor sensitivityswitchto
"L
(Low)". (See ''SETTINGS''.)
*Eithermove the moving object or the object causingthe suddentemperature
changesoutside the detectionarea or change the area setting. (See
"SETTINGS'.)
\
Theexternalsensor area does not match
the camera angleof view.
.Align
the external sensorarea and the camera angle of view.
(See
"ADJUSTMENTS'and "SETTINGS".)
Model
No.
JDW-C
Thewiringis incorrect or a lineis open or
shorted. Checkthe wiring and wire correctly.
(See
"MOUNTING
AND
CONNECTION'.)
@The picture is
dark,blurred,or
not displayedat
all.
Power SuDDlied from the master station The camera window is
dirtv.
Cleanthe lens with lens cleaneror with a clean,
soft,
damD cloth.
Any placeblown
on
by a fan, the
outdoorunit of an &-conditioner,
or any other place subjectto
suddentemperaturechanges.
4ny place where sunlight getsin
heangle of view of the sensor
:amera directly or indirectly.
4ny place too close to
luorescentlamps or directly
'acing powerful illumination.
Any unstableplacesubjectto
vibration or mechanicalshock.
-10
-
+50
"C
Operatingtemperaturerange
Storagetemperature range
Operatinghumidityrange
The outside temperaturedropped
suddenly and the camera window has
foggedup.
When the temperaturesinside and outside the product even out,the camera
window returns to normal.
-20
-
+60
"C
85%(max.)
@There arewhite
lines
on
the
screen.
@The screenis
t
flickering.
Pictureelement 1/3-inchcolor CCD Thereis a bright light source inthe
cameraangleof view. *Eitherremove the light source, adjustthe angle
so
that the light does not come
intothe angle of view, or change themounting location of the main unit. (See
"ADJUSTMENTS".)
/
Camera anale
of
view (horizontal
x
vertical)
71
5"
x
53.4" (f=3.8)
Minimum illumination
1
.o
lux
Thereis a fluorescent lampnearby.
This
is not abreakdown. Block out the light from the fluorescentlamp.
Sensor operation display light
Sensor detectionmethod
Sensor detectionarea
Lightsup green when the sensor detects something(Can be switchedOFF with the select switch)
Heat ray type
Max.
5
meters, approx.
70"
Sensor detectionspeed 0.3
-
1.5
mlsec.
Sensor sensitivitvswitchina Switchable among three levels H (high),
M
(medium), and
L
(low)
Amrox. 30 sec. after Dower comes onSensor startuD time
On
any surfacethat moves or is
affectedby wind. In or near any place subject to
steam or oilfrom an exhaust
duct.
Externalsensor input
Internalsensor switching
An
externalsensor can
be
connectedand operated
in
either an
"AND"
or
"OR"
configurationwith this unit.
The internalbodydetectionsensor can be controlledto be "ON"or "OFF".
Aiphonewarrants its products to be free from defectsof material and workmanshipunder normaluse and servicefor a period of
two years after delivery to the ultimateuser and will repair free of charge or replace at
no
charge, should it becomedefectiveupon
which examinationshall disclose to be defectiveand under warranty. Aiphone reserves unto itself
the
sole right to make the final
decisionwhether there is a defect in materialsand/or workmanship; and whether or not the product is within the warranty.
This
warranty shallnot applyto any Aiphoneproduct which has been subjectto misuse, neglect, accident,or to use in violationof
instructionsfurnished,nor extendedto units which have been repaired or alteredoutside of
the
factory.This warranty does not
cover batteriesor damage caused by batteries used in connectionwith the unit.
This
warranty covers bench repairs only, and any
repairs must be made at the shopor place designatedin writing by Aiphone. Aiphone will not be responsiblefor any costs incurred
involvingon site service calls.
Internalspeaker The internalspeaker can be controlledto be
"ON"
or "OFF"with the speaker select switch.
Internalmic. The mic. sensitivitv can beadiusted withthe mic. sensitivitvvolume.
Master stationswitch Switchable accordinato the master station version.
-
ConnectionprecautionsA
.Use two conductorwire from the JDW-Cto the master station.
Do
not use coaxial cable.
.When using two cameras, alwaysuse one two conductor wire for each camera.
If
you connect
two
cameraswith one multi-
conductorwire,
the
camerasmay not operate correctly.
@If
the wiring isrouted togetherwith high voltage AC wiring, otherpower wiring, wiring for electricallights, and telephone
lines,this can disrupt the picture and soundquality and cause malfunction. Either use separateconduitsor
run
wiresin
separatepaths from each other.
.When existingwiring is used,for sometype of wiring,
this
systemmay not operatecorrectly. Changingthe wiring restores
normaloperation.
k50"
leftlright, -20" to
-55"
up/down (The horizontaldirectionis
O".)
(The IeWrightand up/down angles can bothbe changed inincrements
of
5".)
Camera
Sensor
Angle
adjustment
range
k50"
leftlright,
-20"
to
-55"
up/down (The horizontaldirectionis
OO.)
(The left/riahtangle can
be
changed in increments
of
10"
and the uddownangle in increments
of
5O.I
InstallationDlaces Indoors/Outdoors
Weather-resistant
Protective structure
Weight
Dimensions (mm) Approx. 400 g
102(W)
x
182 (H) x
94
(D)
