Air Design 1109NNTJTO02A10 User manual

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
1
PART # : 1109NNTJTO02A10
SUPER-BOLT FENDER FLARES SET
WARNING!! Rust Prevention Oils and other Petrol Based Anti Rust Treatments for Vehicles
may aect 3M´s Double Adhesive Tape and Polyurethane Adhesive performance!
WARNING!! Do not install Hood Scoops or other Body Parts directly Over Wrapped
areas. Before installation of the parts , you must leave at least a 1/4” (6mm) perimetral
clearance “Free from Vinyl” surrounding the part, before Part installation.
WARNING!! Do not install Hood Scoops Over Vinyl or Over Plastic Stripes on the Hood: 3M
Adhesive Tape and PUR Adhesive must always be in contact with the Sheet Metal of the vehicle.
WE RECOMMEND
2 PERSONS FOR
INSTALLATION
24 hrs
AFTER INSTALLING
DOT NOT WASH CAR
READ CAREFULLY
BEFORE INSTALLATION
WASH BEFORE
INSTALLING
VERSION 0

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
2
Mexico ([phone] / USA [phone]
ITEM DESCRIPTION DRAWING AMOUNT
A*SUPER-BOLTS RUBBER STUDS 36 PCS
B*STAINLESS SUPER-BOLT M6x14 36 PCS
C*STAINLESS LOCKNUT M6 8 PCS
DPHILLIPS - HEX HEAD SEMS TAPPING SCREW M 6.3 X 25 M 16 M
WASHER / 10 M 4 PCS
E*PVC TRIM 33 FT
FAUTOMOTIVE ADHESION PROMOTER TESA #60153 1 PC
GAPPLICATION SPONGE 1 PC
HGREASE PENCIL 1 PC
ITHREADLOCKER 222 1 PC
J
SUPER-BOLT PRESSER 1 PC
TOOLS
10mm
¼”
CHECK LIST *Already installed in the part

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
3
FRONT RIGHT & LEFT FLARE
WASH WITH WATER, DETERGENT AND
SOFT CLOTH OR SPONGE
ONLY IF YOUR TACOMA HAS OE FENDER FLARES INSTALLED
The ideal temperature range of the part and the vehicle when installing must be 16ºC (60ºF) to 40ºC (104ºF), this
guarantees a correct assembly.
10mm
10mm
REMOVE SCREWS
REMOVE MUD GUARDS
REMOVE SCREWS
REMOVE ORIGINAL FLARES

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
4
Mexico ([phone] / USA [phone]
10mm
SECURE THE PART
MARK SILHOUETTE AND SUPER-BOLTS POSITIONS
HASH MARKS
DRAW CENTER HASH MARK WITH
GREASE PENCIL AT CENTER, BOTH
SIDES, ON EACH SUPER-BOLT AND
SHEET METAL. THIS WILL ENSURE
WHEEL FLARE WILL BE CENTERED TO
GREASE PENCIL OUTLINE.
8
9

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
5
APPLICATION
AREA
10mm
REMOVE
UNSCREW
INNER VIEW
WARM SURFACES WITH HEAT GUN IF SURFACE
TEMPERATURE IS TOO COLD.
ALIGN WHEEL FLARE TOP EDGE
WITH THE GREASE PENCIL HASH
MARKS AND PLACE.

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
6
Mexico ([phone] / USA [phone]
10mm
APPLY PRESSURE ON EACH SUPER-BOLT
SECURE THE PART
WE RECOMMEND
2 PERSONS FOR
INSTALLATION
REMOVE SUPER-BOLTS (B)
UNSCREW
8
ONLY THE ONES WITH RUBBER STUD
¼”
10mm
REMOVE
9

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
7
PRESS SUPER-BOLTS STUDS (A)
SUPER-BOLT INSTALLATION
SUPER-BOLT STUDS
FULL SURFACE CONTACT IS CRITICAL FOR GOOD
ADHESION PERFORMANCE. ALWAYS APPLY FIRM
PRESSURE WHEN MOUNTING ADD ON PARTS
AND TAPES.
ATTENTION
58 - 72 PSI
2
PRESSURE POINTS

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
8
Mexico ([phone] / USA [phone]
PLACE SUPER-BOLTS STUDS
ATTENTION
APPLY LOCTITE THREADLOCKER TO SUPER-BOLTS THREAD PLACE SUPER-BOLTS
10mm
SECURE THE PART
CLEAN OFF GREASE PENCIL MARK ¼”
DON’T FORCE
THE TURN
ONCE IT HAS
STOPPED

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
9
REAR LEFT & RIGHT FENDER EXTENSION ONLY IF YOUR TACOMA HAS OE
FENDER FLARES INSTALLED
10mm
10mm
REMOVE SCREWS
REMOVE MUD GUARDS
REMOVE SCREWS
REMOVE ORIGINAL FLARES

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
10
Mexico ([phone] / USA [phone]
9
10mm
MARK SILHOUETTE AND SUPER-BOLTS POSITIONS
SECURE THE PART
HASH MARKS
DRAW CENTER HASH MARK WITH
GREASE PENCIL AT CENTER, BOTH
SIDES, ON EACH SUPER-BOLT AND
SHEET METAL. THIS WILL ENSURE
WHEEL FLARE WILL BE CENTERED TO
GREASE PENCIL OUTLINE.
8

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
11
APPLICATION
AREA
10mm
REMOVE
UNSCREW
INNER VIEW
ALIGN WHEEL FLARE TOP EDGE
WITH THE GREASE PENCIL HASH
MARKS AND PLACE.

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
12
Mexico ([phone] / USA [phone]
10mm
SECURE THE PART
APPLY PRESSURE ON EACH SUPER-BOLT
10mm
ONLY THE ONES WITH RUBBER STUD
9
UNSCREW
REMOVE
REMOVE SUPER-BOLTS (B)
8
¼”
WE RECOMMEND
2 PERSONS
FOR INSTALLATION

INSTALLATION MANUAL
Tacoma 2016 - 2022
www.airdesignusa.com
DATE: 07.01.20 PG.
13
PRESS SUPER-BOLTS STUDS (A)
SUPER-BOLT INSTALLATION
SUPER-BOLT STUDS
FULL SURFACE CONTACT IS CRITICAL FOR GOOD
ADHESION PERFORMANCE. ALWAYS APPLY FIRM
PRESSURE WHEN MOUNTING ADD ON PARTS
AND TAPES.
ATTENTION
58 - 72 PSI
2
PRESSURE POINTS

INSTALLATION MANUAL
Tacoma 2016 - 2022
PG.
14
Mexico ([phone] / USA [phone]
10mm
SECURE THE PART
PLACE SUPER-BOLTS STUDS (A)
INSTALLED PARTS
PLACE SUPER-BOLTS (B)
CLEAN OFF GREASE PENCIL MARK
DON’T FORCE
THE TURN
ONCE IT HAS
STOPPED
¼”
ATTENTION
APPLY LOCTITE THREADLOCKER TO SUPER-BOLTS THREAD