Air Oasis iAdapt Air S User manual

For safety and to ensure proper use carefully
read the contents of this manual before
operating the purifier. R2022.03.20

www.airoasis.com/policies/#warranty-policy
Warranty Guaranteed

Carefully read the entire contents of this manual.
Do not use outdoors or on wet surfaces.
Do not use the purifier in areas of extreme heat or in the presence of flamma-
ble gas
Do not handle the wires or appliance with wet hands.
Do not use damaged or uninsulated wires. If appliance is not working proper-
ly, call a customer service representative at [phone].

Using the four included screws, attach the base. This will prevent
injuries by ensuring the unit is stable and will not fall over.

After connecting the power supply, you will hear one beep and the control
panel will illuminate for two seconds before entering standby mode.
Fan Speed: Cycles the fan speed to Low, Medium or High.
Timer: Sets an auto off timer for 2, 4 or 8 hours.
Child Lock/Sleep Mode: Press for three seconds until you hear a single beep,
signifying Child Lock/Sleep Mode has been activated. Once activated, all
settings will be locked and control panel lights will dim. Tap any button to
temporarily illuminate status icons to view locked settings. Pressing the Child
Lock/Sleep Mode button for three more seconds will unlock the control panel.
Smart Mode: Press to activate Smart Mode. While in Smart Mode, the fan
speed will automatically adjust according to your air quality. If the iAdaptAir®
senses a reduction in air quality, the fan speed will automatically increase.
When the air quality improves, the fan speed will automatically decrease to
extend filter life.
Power Button:
1st press turns on the purifier, ionizer, UV light and low fan speed.
2nd press turns off the ionizer.
3rd press turns off the UV light.
4th press keeps the UV light off and turns the ionizer on.
5th press switches the purifier to standby mode.

Viewing Wifi Stauts
Turn WiFi On/Off
Press the Smart Mode button once while the purifier is in standby (power
cord plugged in to the purifier, but not powered on). The smiley faces will
show the status of the WiFi connection:
Green Flashing Happy Face = Not Connected
Solid Green Happy Face = Connected
Red Frowning Face = WiFi Turned Off
Hold the Fan Speed button for more than three seconds while the purifier is
in standby mode. The WiFi will turn off. Refer to the WiFi status above.
Unplugging the purifier automatically resets the WiFi status to be turned on.
Hold the Smart Mode button for more than three seconds and it will reset
the WiFi network name and password.
The status will show for one minute and then return to normal automatically.
IMPORTANT: Do not reset the purifier by step 2 if it is still registered in the app.
You will need to delete the purifier from the app before reseting.

Dust Guard Maintenance
Ensure the iAdaptAir®is unplugged from its power source before
performing any maintenance.
Pivot the dust guard outwards and lift up to remove it from the purifier.
Use a vacuum to remove any debris. Wipe down the dust gaurd with a
damp rag. Dry before replacing in the iAdaptAir®.

Clean the bi-polar brush heads periodically for optimal effectiveness.
Use a pipe cleaner or something similar to insert into the two holes in
front of the brushes to knock off any debris buildup.
Use a soft cloth to clean the exterior surfaces (do not use chemicals or
alcohol).

When to Change Your Filter
How to Change Your Filter
Your filter is brand new!
No change needed
soon.
Your filter has been
used some. You still
have 75% filter life
remaining.
Your filter is getting close
to a change. You still
have 50% filter life
remaining.
Change your filter soon.
Only 25% filter life is
remaining.
Remove the iAdaptAir® from power. Open the filter cover by sliding it to
the right.
Take out the old filter and replace with a new filter.

Close the filter cover.
Power the iAdaptAir® back on. Press and hold the Filter Replacement
Reminder for 3 seconds to reset it.

For optimal performance and maximum efficiency of your iAdaptAir®, ensure all
UV lamps are replaced annually.
Ensure the iAdaptAir®is unplugged from its power source before
performing any maintenance. UV lamp may be hot. Allow time for the lamp
to cool before removing it.
Remove the filter cartridge and dust guard (See page 10).
Slightly rotate and move the UV lamp forward to remove it from the clips.
Reverse the previous steps to install the new UVC lamp.
Squeeze the release lever on the back of the lamp connector while pulling
the connector away.
Release
lever Connectors
WARNING
OPTICAL RADIATION EXPOSURE HAZARD
DO NOT ATTEMPT TO OPERATE PURIFIER
WITH THE AHPCO®CELL EXPOSED
DO NOT ATTEMPT TO REPLACE AHPCO®
CELL WITHOUT DISCONNECTING POWER
PERMANENT EYE AND SKIN DAMAGE MAY RESULT.
Hg lamp contains mercury. Manage in accord with disposal laws. Contact local waste
management for disposal sites and procedures.

Purifier Not Turning On
Ensure the following:
The power button has been pressed.
The power cord is not loose or broken.
The correct plug connector is in use. Your iAdaptAir® comes with
international plugs. Ensure you are using the correct one for your
country.
Odors From the Purifier
Ensure the following:
There is no debris buildup. Your purifier requires regular filter
replacements.
The filter has more than 25% life remaining (see page 12).
Poor Performance
Something Else?
Ensure the following:
The purifier is in a space with good air ventilation. Your purifier
requires proper air flow to cycle through and clean your air.
Neither the air inlet nor outlet are obstructed.
If you are experiencing an issue with your air purifier that is not listed
here, please contact our Customer Excellence team.

iAdaptAir-S iAdaptAir-M iAdaptAir-L
Warranty Lifetime Warranty Lifetime Warranty Lifetime Warranty
Voltage 100-240VAC 100-240VAC 100-240VAC
Rated Power 8 WATTS 24 WATTS 32 WATTS
Dimensions 5.4in x 8.5in x 9.7in 11.2in x 11.2in x 28.3in 11.2in x 11.2in x 37in
Weight 7 lbs. 15.5 lbs. 20 lbs.
Fan Speed Low 700rpm, Medium
1000rpm, High
1200rpm
Low 700rpm, Medium
1000rpm, High
1200rpm
Low 700rpm, Medium
1000rpm, High
1200rpm
Timer Settings 2hr, 4hr, 8hr 2hr, 4hr, 8hr 2hr, 4hr, 8hr
Ozone 0.00 PPM 0.00 PPM 0.00 PPM
Replacement Filter
Cartridge
Model #: AOIA-SF
HEPA, carbon and
AHPCO®
Model #: AOIA-MF
HEPA, carbon and
AHPCO®
Model #: AOIA-LF
HEPA, carbon and
AHPCO®
Ion Output 20,000,000 positive
and negative 20,000,000 positive and negative 40,000,000 positive and negative
Noise Level 25dB low speed to
52dB high speed 25dB low speed to 52dB high speed 25dB low speed to 52dB high speed