Aircat 6700-5-336 Datasheet

MODEL: 6700-5-336
5” Orbital Palm Sander

SPECIFICATIONS
Important Warnings - Sanders & Polishers
1. Eye protection, safety gloves and safety aprons must always we worn when operating a sander or
polisher.
2. Never adjust the sander or polisher or change the backing pad, sanding disc, sanding belt or
polishing bonnet unless the air supply and air hose is disconnected from the tool
3. Only use backing pads and polishing backing pads that have a rated speed then same as the sander
or polisher or higher.
4. Never attempt to modify or adapt a sander or polisher for use with a grinding wheel or cut-off wheel
or wire brush.
5. Only personnel trained in the correct methods to change pads, sanding discs, sanding belts and
polishing bonnets should conduct these operations.
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4”NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8”I.D. and ttings should have the same inside dimensions.
Air Supply
Model No. Pad Size
(in)
Orbit
(in)
Pad Type No.
Vacuum
Pad Holes
Free
Speed
(RPM)
Weight
(lbs)
Length w/
Pad Fitted
(in)
Width w/
Pad Fitted
(in)
Height w/
Pad Fitted
(in)
Noise Level
d(B)A
Vibration
m/sec2
Average
Air (CFM)
Air Inlet
(in.) NPT/
BSP
6700-5-336 5 3/16 Hook & Loop 0 11,000 2.0 6.7 5.0 4.3 75 0.8 1.6 1/4

MODEL: 6700-5-336
5” Orbital Sander
Exploded View & Parts List
Ref
#
Part Number Description Qty Ref
#
Part Number Description Qty.
1 9OB10601 HOUSING 1 27 9ST246014 PIN 1
2 9OB-03 SNAP RING 1 28 9ST241624 BUSHING 1
3 9OB-04 O-RING 1 29 981326 PIN 1
4 9OB10604 VALVE STEM 1 30 9STOB-25 FRONT PLATE 1
5 9SX-11 SILENCER 2 31 9OB-26A BEARING 1
6 9OB-02 O-RING 2 32 9OB-28 WASHER 1
7 9ST-OB10607 REGULATOR 1 33 9E-29 WASHER 1
8 9OB10608 LEVER 1 34 9ST70407 ROTOR KEY 1
9 9OB10609 HOUSING COVER 1 35 9STS560-31 MOTOR SHAFT BALANCER
(5",3/16")
1
10 9OB10610 SPRING PIN 1 36 9OB-30 SNAP RING 1
11 9OB10611 MUFFLER 1 37 9OB-31.3 BEARING 1
12 9OB10612 PACKING 1 38 9OB-23.2A SHIM 1
13 9OB10613 EXHAUST SLEEVE 1 39 9OB-31.4 BEARING 1
14 9OB-06 WASHER 1 40 9RS0132A DUSTPROOF WASHER 1
15 9STOB-08 VALVE 1 41 9OB-33 SNAP RING 1
16 9OB-09-1 SPRING 1 42 9S560-34 SHAFT 1
17 9OB10617 AIR INLET (NPT)(USA) 1 43 9OB-16.1 WASHER 1
17 9OB10617-1 AIR INLET (BSP)(UK) 1 44 9OB10642 HOUSING COVER (3/16") 1
18 9OB106N18 MUFFLER BODY 1 45 9OB10643 SCREW 1
19 9OB10651 SLEEVE 1 46 9OB10644 LOCK NUT 1
20 970410 SNAP RING 1 47 9OB10645 SHROUD 1
21 970048A BEARING 1 48 938-5V0Y PAD HOOK-UP 1
22 9OB-16.2 RUBBER BUSHING 2 49 9OB10649 HOUSING COVER (3/16") 1
23 9STOB-19 REAR PLATE 1 50 9OB-39-22 STOP SPANNER 1
24 9OB-20-2 ROTOR BLADE 5 51 9RS0133 WASHER 1
25 9STOB-21 ROTOR 1 52 9SX-11A SILENCER 1
26 9ST246021A CYLINDER 1