Grizzly T20644 User manual
COPYRIGHT © MARCH, 2008 BY GRIZZLY INDUSTRIAL, INC.,
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR10583 PRINTED IN CHINA
MODEL T20644
34º ANGLE FINISH NAILER
INSTRUCTION MANUAL
T20644 34° Angle Finish Nailer–2½"
-2-
Safety Instructions For Pneumatic Tools
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before operation.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use pneu-
matic tools in damp or wet locations,
or where any flammable or noxious
fumes may exist. Keep work area
well lighted.
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
6. MAKE WORKSHOP CHILD PROOF
by locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate for
which it was designed.
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a job
for which it was not designed.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates an imminently hazardous situation which,
if not avoided, WILL result in death or serious injury.
This symbol is used to alert the user to useful
information about proper operation of the equipment.
SAFETY
NOTICE
T20644 34° Angle Finish Nailer–2½" -3-
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without stretch-
ing.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear a protective
hair covering to contain long hair.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask if cut-
ting operation is dusty. Everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
14. SECURE WORK. Use clamps or a
vise to hold work when practical. It
is safer than using your hand and
frees both hands to operate tool.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger and
always disconnect from air when
not in use.
17. DISCONNECT TOOLS before ser-
vicing, changing accessories, or
moving to another location.
18. DO NOT OVERREACH. Keep
proper footing/balance at all times.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for bind-
ing and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect machine operation. Repair or
replace damaged parts.
21. NEVER LEAVE UNATTENDED
TOOL CONNECTED TO AIR.
Disconnect the air hose and do not
leave tool until it is relieved of any
built up pressure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL
WHILE UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC
TOOLS. Hoses can easily become
a tripping hazard when laid across
the floor or spread out in a disorga-
nized fashion.
Safety Instructions For Pneumatic Tools
T20644 34° Angle Finish Nailer–2½"
-4-
Additional Safety Instructions for Nailers
1. HAND INJURIES: Do not place your
hands near the nail point of entry. A
nail can deflect and tear through the
surface of the workpiece, puncturing
your hand or fingers.
2. COMBUSTIBLE GASES: Never con-
nect the nailer to pressurized oxy-
gen or other combustible gases as a
power source. Only use filtered, lubri-
cated, and regulated compressed air.
3. SAFE HANDLING: Never point the
nailer at others! Do not keep the trig-
ger pulled when loading fasteners,
carrying, or holding tool. Carry the
nailer only by the handle, never by
any other part. Do not carry the nailer
by the air hose. Disconnect the nailer
from the air hose when going up and
down ladders.
4. MODIFICATIONS: DO NOT modify
this tool or bypass the safety nose
mechanism.
5. CHECK VALVE: Do not use a check
valve or any other fitting that allows
air to remain in the tool.
6. HOSE USAGE: Make sure your air
hose is designed for the tool in use, is
in good condition, and is long enough
to reach your work without stretching.
However, an overly long air hose in
the work area may be a tripping haz-
ard if not kept out of the way.
7. OPERATING QUESTIONS: If you
are not sure about the intended oper-
ation, stop using the nailer. Seek
formal training.
8. CLEANING: Never use gasoline or
other flammable liquids to clean the
nailer; vapors in the nailer will ignite
by a spark and cause it to explode.
9. MAINTENANCE: Always disconnect
air from the nailer when servicing or
installing nails. During maintenance,
a nailer connected to air may fire acci-
dentally, causing serious personal
injury.
10. COMPRESSED AIR RATING: Do
not connect the nailer to compressed
air that exceeds 120 PSI.
T20644 34° Angle Finish Nailer–2½" -5-
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warning
may result in serious personal injury.
Operating this nailer can propel
objects into the air, causing imme-
diate eye damage. To protect your-
self, always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at up to 85-90 deci-
bels. To protect your hearing, always
wear ANSI approved ear protection
when operating this nailer.
Read the manual before operation.
Become familiar with this nailer, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety or
operational information is not under-
stood or followed.
Nailer accidents routinely happen
while moving the gun to another
location, such as up ladders, to
another room, or even another job
site. Always disconnect the gun
immediately after use and never
transport the gun while connected to
the air—even if the air compressor is
disconnected from its power source!
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individu-
al working conditions. Use this and
other tools with caution and respect.
Failure to do so could result in seri-
ous personal injury, damage to equip-
ment or poor work results.
T20644 34° Angle Finish Nailer–2½"
-6-
INTRODUCTION
If you have any comments regarding this
manual, please contact us:
Grizzly Industrial, Inc.
C/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
Web Site: http://www.grizzly.com
We are proud to offer the Grizzly Model
T20644 34º Angle Finish Nailer–2½". This
model is part of a growing Grizzly family of
fine pneumatic tools. When used accord-
ing to the guidelines set forth in this man-
ual, you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s
commitment to customer satisfaction.
The specifications, details, and photo-
graphs in this manual represent the Model
T20644 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
Foreword Contact Info
Nailer Specifications
Nail Size .....................15 gauge finish nails
Nail Length ....................................1¼"-2½"
Magazine Capacity ................................. 80
Air Inlet ...........................................¼" NPT
Weight ................................................5 lbs.
Operating Pressure .................. 60-100 PSI
Max Operating Pressure ................ 120 PSI
Functional Description
The Model T20644 is designed to toenail
into corners and shoot at any angle. This
nailer is ideal for door, window, exterior,
and decorative trim, cabinet work, and fin-
ish paneling. The Model T20644 features
a 360° exhaust port, comfort grip rubber
handle, economical air consumption with
low noise, narrow nose for tight spots, and
quick jam release mechanism.
T20644 34° Angle Finish Nailer–2½" -7-
SETUP
Your Model T20644 left our warehouse
in a carefully packed box. If you discover
the nailer is damaged after you have
signed for delivery, please immediately
call Customer Service at (570) 546-9663
for advice.
Save the containers and all packing mate-
rials for possible inspection by the ship-
ping company. (Otherwise, filing a claim
can be difficult.) When you are completely
satisfied with the condition of the ship-
ment, inventory the equipment.
After you remove the nailer case from the
box you should find the following.
Model T20644 Inventory (Figure 1)
A. 34° Finish Nailer−2½ ......................... 1
B. Safety Goggles .................................. 1
C. Oil ....................................................... 1
D. Hex Wrench 3, 4, 5mm ............. 1 Each
E. Case ................................................... 1
Figure 1. Model T20644 inventory.
B
C
D
E
A
InventoryUnpacking
T20644 34° Angle Finish Nailer–2½"
-8-
The Model T20644 is designed to be oper-
ated at 60-100 PSI using clean, dry, regu-
lated, compressed air. DO NOT exceed
the 120 PSI maximum operating pres-
sure for your model.
Before using your new nailer, regulate the
air pressure to find the optimum setting
within the specified operating range. Start
by testing the nailer at a low setting, then
increase the air pressure as needed for
satisfactory results.
An in-line filter/lubricator/regulator unit can
be installed, as depicted in Figure 2.
This filter/lubricator/regulator unit will
protect your tool from damaging water
build-up, allow you to adjust and maintain
constant air pressure to your tool, and
save you the inconvenience of having to
manually lubricate your tool every time
you use it.
Quick
Connector
Quick
Coupler
Air Hose Quick
Coupler
Quick
Connector
Lubricator
Filter
Regulator
Air
Compressor
Your
Tool
Figure 2. Typical filter/lubricator/regulator installation order.
Compressed Air
System
Check the current Grizzly catalog for avail-
ability of this unit. If you plan on install-
ing a filter/lubricator/regulator unit in your
compressed air system, always follow the
connection instructions that come with
the unit.
Exceeding the maximum permissible
operating pressure may damage the
nailer and cause it to malfunction. To
reduce your risk of personal injury,
DO NOT allow the air pressure to
exceed the recommended pressure
for this nailer!
T20644 34° Angle Finish Nailer–2½" -9-
Safety Yoke
A safety yoke mechanism on the nose
of the nailer acts as a secondary safety
device. When the trigger is pressed, the
nailer will not fire until the safety yoke
mechanism is depressed.
Before you use your nailer for the first
time, check the safety yoke mechanism to
ensure proper function. To do this:
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger, depress
the safety yoke mechanism against a
scrap piece of wood that is clean and
free of any knots, nails, or other foreign
objects.
— If the nailer does not fire, then the
safety yoke mechanism is working
correctly.
— If the nailer does fire when you
do this, immediately disconnect the
nailer from the air supply and call
Grizzly Technical Support at (570)
546-9663 for help.
— If the nailer fires when the trigger
is pulled without the safety yoke
mechanism being depressed, then
the nailer is not working properly.
— If either of these conditions develop
after you have used your nailer for a
period of time, check the lubrication
of these mechanisms.
The safety yoke is a mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
DO NOT attempt to modify or bypass
the safety yoke mechanism to make
the nailer fire without pushing the
safety yoke down.
T20644 34° Angle Finish Nailer–2½"
-10-
OPERATIONS
Loading
When replacing nails in your Model
T20644, follow these guidelines:
Gauge: ................................................... 15
Length:........................................ 11⁄4" -21⁄2"
Capacity: ................................................ 80
Angle: ...................................................34°
Note: A number of manufacturers' nails
may fit the Model T20644. However, for
best performance, we recommend you use
the following Grizzly nails:
G6085-G6088, G9545, G6090, G3693-
G3697.
3. Slide the nail stick all the way down to
the nose of the nailer.
4. Pull the magazine pusher all the way
back, then let it come forward until it
rests against the end of the nail stick.
Figure 3. Loading finish nails into nailer.
Pusher
Release
To load your nailer:
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
2. Insert a nail stick into the T-slot at the
top of the magazine as shown in Figure
3.
T20644 34° Angle Finish Nailer–2½" -11-
Operating
If you have not read the safety instruc-
tions in this manual, do not operate the
nailer.
Before you operate your nailer, place one
drop of the included oil into the quick con-
nect fitting where the nailer connects to
the air supply.
To operate your nailer:
1. Connect the nailer to the air supply.
2. To test for proper nail penetration, hold
the nailer perpendicular to the surface
of a piece of clean scrap wood that is
thick enough for the length of nails you
have loaded.
3. Depress the safety yoke mechanism on
your workpiece.
4. Before pulling the trigger, make sure
your free hand and other body parts
are positioned out of the way of a
potential path of a nail in case of deflec-
tion.
Deflection is caused when grain irregu-
larities, knots or foreign objects inside
the wood cause the nail to change its
path, resulting in the nail puncturing the
surface of the workpiece, as shown in
Figure 4.
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the nail deflects.
5. Pull the trigger. If the nail drives into the
wood far enough, continue with your
intended operations. If the nail goes
too far or not far enough, adjust the
depth adjustment knob described in the
Adjusting Depth section.
Figure 4. Example of nail deflection.
Adjusting Depth
The Model T20644 features a knurled
adjustment knob (Figure 5) for setting the
nail depth into the workpiece.
Rotate this knob to adjust the workpiece.
To find the correct nail penetration depth,
use trial-and-error on a scrap workpiece of
the same type of material as your work.
Figure 5. Depth adjustment knob.
T20644 34° Angle Finish Nailer–2½"
-12-
All nailers occasionally get jammed.
To clear a jammed nail from the dis-
charge area on the Model T20644:
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
Figure 6. Releasing quick release latch.
Figure 7. Removing driver guide cover.
Clearing Jammed
Nails
Always disconnect air from nailer
whenever clearing a jammed nail!
3. Flip up the quick release latch located
on top of the nailer nose assembly, as
shown in Figure 6.
4. Remove the driver guide cover (Figure
7).
5. The jammed nail should now be vis-
ible; remove it from the discharge area
with needle nose pliers.
6. Replace the driver guide cover and
snap the quick release latch back into
operating position.
2. Release the magazine pusher and
slide the nail stick out of the back of
the magazine.
T20644 34° Angle Finish Nailer–2½" -13-
Replacing Pistons/
O-Rings
Repair pistons are cheap insurance in the
event that a piston or piston shaft becomes
worn out.
The part number for the repair piston for
this nailer is #PT20644098. To order, call
Customer Service at (800) 527-4777.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
To replace a piston:
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
2. Remove all nails from the magazine.
3. Remove the four cap screws on the top
of the nailer, near the exhaust port.
4. Remove the top cap.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
6. Open the magazine.
7. Watch the discharge area and push the
top of the piston with your finger. You
will see the piston shaft slide down the
discharge area.
8. With a long flathead screwdriver or sim-
ilarly shaped tool, push the piston shaft
back inside the nailer until you can grip
the piston head and remove it from the
cylinder. (Be careful not to scratch the
discharge area when pushing the pis-
ton shaft with the screwdriver.)
9. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
10. Insert the new piston in the cylinder.
Make sure that the grooves on the pis-
ton shaft line up with those on the guide
at the bottom of the cylinder. The new
piston should easily slide into the cyl-
inder. DO NOT force the piston into
the cylinder! If the piston is not easily
inserted, double-check the alignment of
the piston shaft with the grooves on the
guide.
11. After the piston is inserted correctly,
close the magazine. Replace the top
cap assembly and tighten the four cap
screws.
12. For more assistance, or to install a
complete O-ring set, refer to Parts
Breakdown on Page 16.
T20644 34° Angle Finish Nailer–2½"
-14-
ACCESSORIES
G2820—Pneumatic Tool Oil 8 oz.
G2821—Pneumatic Tool Oil 1 Pint
Use the right oil! This pneumatic tool oil
offers outstanding heat displacement and
friction reduction without eating away at
delicate air components like detergent
motor oils. Stock up with extra bottles to
avoid costly downtime.
Figure 10. Red rubber air hose.
G8114—3⁄8" x 25 Ft. Air Hose
G8115—3⁄8" x 50 Ft. Air Hose
G8116—3⁄8" x 100 Ft. Air Hose
Multi-purpose red rubber air hose is flex-
ible and abrasion resistant. Rated for 200
PSI, this air hose has a bursting strength
of 800 PSI and 1⁄4" NPT ends.
Figure 9. Models H3258 & H3259
Filter/Lubricator/Regulators.
H3258—Filter/Lube/Regulator 3⁄8"NPT
H3259—Filter/Lube/Regulator 1⁄2"NPT
These units are indispensable for prolong-
ing the lifespan of your air tools. Filter
keeps water/rust out. Lubricator features
adjustable automatic lubrication. Regulator
allows you to control the optimum PSI
delivery for each air tool. Maximum pres-
sure for each unit is 150 PSI.
Figure 11. Recoil air hose.
H3275—1⁄4" x 25' Recoil Air Hose
H3275—1⁄4" x 50' Recoil Air Hose
These recoil air hoses are ideal for nail-
ers and staplers because they are light
weight and offer maneuverability in tight
places that is unmatched by rubber hoses.
Coiled springs protect the ends from kink-
ing. (Prices are less than you'll spend on
lunch!)
Figure 8. 1⁄4" NPT air fittings.
H3175—1⁄4" NPT Female, Quick Coupler
H3176—1⁄4" NPT Male, Quick Coupler
H3177—1⁄4" NPT Male, Plug
H3178—1⁄4" NPT Female, Plug
H3175 H3176
H3177 H3178
H3258 H3259
T20644 34° Angle Finish Nailer–2½" -15-
CLEANING & LUBRICATION
Cleaning
Use non-flammable solvent to clean the
nose assembly of the nailer. Always be
sure that the nailer is dry before using it
again.
Do not allow dust, chips, sand, etc. into
the air connectors or into the body of the
nailer; this may result in leaks and damage
to the nailer and the air couplings.
Lubricating
Standard pneumatic tool oil has been
included with your new Grizzly nailer to
help maintain its useful life. Place two to
six drops of oil in the nailer air inlet (as
shown in Figure 12) before every use, or
after 2 hours of continuous use.
Wipe off any excess oil near the nailer
exhaust to avoid dust build-up. When the
oil that was included with the nailer has
been completely used, replace with Grizzly
Model G2820 Pneumatic Tool Oil.
Another option to manual oiling would be
to install a lubricator in your air compres-
sor line. If your air compressor line already
has a lubricator, then regular lubrication
of your nailer will not be necessary. Just
make sure there is always oil in the lubri-
cator.
Figure 12. Lubricating nailer via air inlet.
Never clean this tool with gasoline
or other flammable liquids. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
T20644 34° Angle Finish Nailer–2½"
-16-
PARTS BREAKDOWN
T20644 34° Angle Finish Nailer–2½" -17-
PARTS LIST
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT20644001 SPECIAL CAP SCREW 51 PT20644051 SPACER
2 PT20644002 AIR DEFLECTOR 52 PEC09M E-CLIP 6MM
3 PT20644003 RUBBER WASHER 53 PT20644053 COMPRESSION SPRING
4 PSB38M CAP SCREW M5-.8 X 25 54 PT20644054 SAFETY NOSE
5 PLW01M LOCK WASHER 5MM 55 PT20644055 SAFETY COVER
6 PT20644006 CYLINDER COVER 56 PSB17M CAP SCREW M4-.7 x 10
7 PSS79M SET SCREW M4-.7 x 6 57 PEC01M E-CLIP 3MM
8 PT20644008 COMPRESSION SPRING 58 PSB18M CAP SCREW M4-.7 x 8
9 PT20644009 SWITCH VALVE SEAT 59 PT20644059 FIXED COVER
10 PORG030 O-RING 29.4 X 3.1 G30 60 PLW03M LOCK WASHER 6MM
11 PORG045 O-RING 44.4 X 3.1 G45 61 PSB02M CAP SCREW M6-1 x 20
12 PT20644012 SWITCH VALVE 62 PT20644062 RUBBER RETAINING RING
13 PT20644013 COLLAR 63 PT20644063 QUICK RELEASE HANDLE
14 PORG065 O-RING 64.4 X 3.1 G65 64 PT20644064 LATCH
15 PT20644015 FIXED RING 65 PT20644065 DRIVER GUIDE COVER
16 PT20644016 SEALING WASHER 66 PRP43M ROLL PIN 3 X 22
17 PT20644017 CYLINDER 67 PT20644067 PIN
18 PORP035 O-RING 34.7 X 3.5 P35 68 PT20644068 DRIVE GUIDE
19 PT20644019 PISTON 69 PT20644069 SPACER
20 PT20644020 BUMPER 70 PSB23M CAP SCREW M4-.7 x 12
21 PT20644021 GUIDE 71 PW05M FLAT WASHER 4MM
22 PT20644022 GASKET 72 PT20644072 LOCK SCREW
23 PT20644023 GUN BODY 73 PT20644073 MAGAZINE
24 PT20644024 RUBBER WASHER 74 PT20644074 FIXED SEAT
25 PT20644025 O-RING 15 X 2.65 75 PT20644075 PUSHER SPRING
26 PORS018 O-RING 17.5 X 1.5 S18 76 PT20644076 PUSHER PIN
27 PT20644027 TRIGGER VALVE SEAT 77 PT20644077 PUSHER SEAT
28 PH7665031 O-RING 6.2 X 1.8 78 PT20644078 SPRING CORE
29 PH7665032 O-RING 6.4 X 2 79 PT20644079 TORSION SPRING
30 PH7665033 O-RING 9 X 1.8 80 PT20644080 PUSHER
31 PT20644031 TRIGGER VALVE GUIDE 81 PN04M HEX NUT M4-.7
32 PH7665036 O-RING 2.5 X 1.5 82 PT20644082 DRIVE NAIL BAR
33 PT20644033 SWITCH VALVE SPRING 83 PSB33M CAP SCREW M5-.8 x 12
34 PT20644034 SWITCH VALVE STEM 84 PW02M FLAT WASHER 5MM
35 PH7665037 O-RING 20.3 X 2.3 85 PT20644085 SUPPORT SEAT
36 PT20644036 TRIGGER VALVE SEAT 86 PFN04M FLANGE NUT M5-.8
37 PT20644037 COMPRESSION SPRING 87 PT20644087 RUBBER HANDLE CASE
38 PRP02M ROLL PIN 3 X 16 88 PT20644088 END CAP GASKET
39 PT20644039 SAFETY SPACER 89 PT20644089 END CAP
40 PT20644040 PIN 90 PSB53M CAP SCREW M5-.8 x 18
41 PT20644041 TRIGGER 91 PT20644091 MALE AIR PLUG 1/4" NPT
42 PT20644042 O-RING 1.7 X 2 92 PT20644092 AIR PLUG DUST COVER
43 PT20644043 SAFETY SEAT 93 PAW03M HEX WRENCH 3MM
44 PN04M HEX NUT M4-.7 94 PAW04M HEX WRENCH 4MM
45 PT20644045 ADJUSTING NUT 95 PAW05M HEX WRENCH 5MM
46 PT20644046 STEEL BALL 2MM 96 PT20644096 CARRYING CASE
47 PT20644047 COMPRESSION SPRING 97 PT20644097 COMPLETE O-RING KIT
48 PRP97M ROLL PIN 3 X 30 98 PT20644098 PISTON REPAIR KIT
49 PT20644049 COMPRESSION SPRING 99 PT20644099 SAFETY GLASSES
50 PT20644050 DRIVE STAND
T20644 34° Angle Finish Nailer–2½"
-18-
TROUBLESHOOTING
Symptom Possible Cause Solution
Air leaking at trig-
ger valve area.
1. O-rings in trigger valve hous-
ing are damaged.
1. O-rings must be replaced
& operation of safety nose
must be checked.
Air leaking. 1. Loose screws in housing.
2. Damaged O-ring(s).
3. Loose air fitting.
4. Damaged housing gasket(s).
1. Tighten screws.
2. Replace O-ring(s).
3. Tighten air fitting & use tef-
lon tape.
4. Replace gasket(s).
Tool skips nails
while discharging.
1. Excessive air pressure.
2. Air leaks.
3. Dirt in nose.
4. Dirt or damage prevents nails
from moving freely in maga-
zine.
5. Inadequate air flow to tool.
6. Worn O-ring on piston or lack
of lubrication.
7. Damaged O-rings on trigger
valve.
8. Worn bumper.
9. Cap seal leaking.
1. Reduce air pressure to tool.
2. Tighten screws and fittings.
3. Clean nose.
4. Clean magazine and
inspect/repair damage.
5. Check fitting, hose, com-
pressor & air pressure.
6. Replace piston O-ring.
Lubricate.
7. Replace trigger valve O-
rings.
8. Replace bumper.
9. Replace cap seal.
Tool runs slowly
or has a loss of
power.
1. Undersized air hose.
2. Nailer is not lubricated.
3. Broken spring in cap assem-
bly.
4. Exhaust port in cap is blocked.
5. Air pressure too low.
1. Use a larger air hose.
2. Lubricate nailer.
3. Replace spring.
4. Clean or replace damaged
internal parts.
5. Increase air pressure.
Fasteners frequent-
ly jam the nailer.
1. Nails are the wrong size.
2. Nails are bent or dirty.
3. Magazine or nose screws are
loose.
4. Driver or driver guide are worn
or damaged.
5. Nails are wrong angle.
1. Use correct nails.
2. Use undamaged, clean
nails.
3. Tighten magazine.
4. Replace worn or damaged
parts.
5. Use correct angle nails.
Nailer does not fire. 1. Nailer is not lubricated.
2. Nail is jammed in magazine or
discharge area.
3. Piston shaft is damaged.
4. Air pressure too low.
1. Lubricate nailer.
2. Clear nailer magazine or
discharge area.
3. Replace piston shaft.
4. Check/increase air pres-
sure.
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly or
indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-
nance. This is Grizzly’s sole written warranty and any and all warranties that may be implied
by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant or represent that the merchandise
complies with the provisions of any law or acts unless the manufacturer so warrants. In no
event shall Grizzly’s liability under this warranty exceed the purchase price paid for the prod-
uct and any legal actions brought against Grizzly shall be tried in the State of Washington,
County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to use
this warranty.
Thank you again for your business and continued support. We hope to serve you again
soon!
WARRANTY AND RETURNS
Table of contents
Other Grizzly Nail Gun manuals
Grizzly
Grizzly G6045 User manual
Grizzly
Grizzly H7664 User manual
Grizzly
Grizzly T21347 User manual
Grizzly
Grizzly G3690 User manual
Grizzly
Grizzly G2413 User manual
Grizzly
Grizzly H7679 Operating instructions
Grizzly
Grizzly 1 1/4" Brad Nailer T20568 User manual
Grizzly
Grizzly G6050 User manual
Grizzly
Grizzly H2911 User manual
Grizzly
Grizzly H7665 Operating instructions
Grizzly
Grizzly G2420 User manual
Grizzly
Grizzly G6049 User manual
Grizzly
Grizzly G3690 User manual
Grizzly
Grizzly H6332 User manual
Grizzly
Grizzly H5527 User manual
Grizzly
Grizzly H7826 User manual
Grizzly
Grizzly H6145 User manual
Grizzly
Grizzly H5527 User manual
Grizzly
Grizzly H7943/H7944 User manual
Grizzly
Grizzly H7679 User manual
Popular Nail Gun manuals by other brands
Bosch
Bosch GSK 18 V-LI Professional Original instructions
Bostitch
Bostitch BRT130-E Original instructions
Interchange
Interchange NSJH38-34 Operator's manual
DeWalt
DeWalt DC616 Original instructions
Harbor Freight Tools
Harbor Freight Tools Central Pneumatic Professional 90437 Assembly and operating instructions
UFO
UFO NSDCN75 Operation manual
