AirLink Communications 5200 Installation and operating instructions

Application Note
for connecting the
AirLink Raven CDPD Modem
to Ethernet Devices using the
IP 5200 from DCB
March 2002
AirLink Communications, Inc.
Confidential Material -Not For Redistribution

AirLink Application Notes
AirLink Communications Page 2www.airlink.com
THIS DOCUMENT CONTAINS CONFIDENTIAL MATERIAL AND
IS NOT INTENDED FOR REDISTRIBUTION.
Information contained herein is the property of AirLink Communications, Inc. and is produced for the
purpose of detailing technology developed by AirLink Communications, Inc. and its employees.
Reproduction or distribution of this document without the express written consent of AirLink
Communications, Inc. is strictly prohibited. This document is subject to change without notice.
Copyright AirLink Communications, Inc, 2001. All rights reserved.
Please send comments to:
Email: [email protected]
Fax: [phone]
Phone: [phone]
Post: AirLink Communications, Inc.
Attention: Technical Publications Dept.
472 Kato Terrace
Fremont, CA 94539

AirLink Application Notes
AirLink Communications Page 3www.airlink.com
CONTENTS
1. OVERVIEW.....................................................................................................................................4
2. INTERNET (TCP/IP) CONNECTION VIA CDPD.....................................................................4
3. ETHERNET DEVICE & IP5200 CABLING & INSTALLATION.............................................4
4. IP5200 CONFIGURATION ..........................................................................................................5
5. AIRLINK RAVEN CDPD MODEM CONFIGURATION.........................................................11

AirLink Application Notes
AirLink Communications Page 4www.airlink.com
1. Overview
This document describes how to connect the AirLink Raven CDPD Modem to the IP5200 Async-
Router from Data Communications for Business (DCB). Information on the IP5200 and DCB is available
at www.dcbnet.com. Additional information about AirLink Communications products is available at
www.AirLink.com
2. Internet (TCP/IP) Connection via CDPD
Normally, remote access to an IP 5200 is done via Dialup Telephone Line. When using CDPD, remote
access to is done via a TCP/IP connection to the CDPD Network (ie: Internet) and the use of a CDPD
Modem connected to a DCBNet IP5200 Single-Port Async-Router.
On the HOST side, access to the CDPD Network could be made using any of the following means:
1. Using a Frame Relay connection into the CDPD Network
2. Using the public Internet
3. Using another CDPD Modem connected to the Host System
3. Ethernet Device & IP5200 Cabling & Installation
Setting up the Ethernet device (PC, RTU, PLC, etc) for communicating over CDPD is fairly
straightforward. All the same configuration settings used for a LAN installation apply to a CDPD
installation. Since the device is actually sitting on a very small LAN, (just the device and the IP5200), the
IP Address would be a private IP, such as: 192.168.1.101. The IP5200 would have an Address in the
same range, such as: 192.168.1.100.
DNS, FTP, SMTP, and Email settings would be for servers visible to the public Internet or in the
case of Frame Relay connections to the CDPD network –IP Addresses visible to the Frame Relay cloud.
(See your Network Administrator or Carrier for more details on which Addresses or server names to use).
When the device initiates Ethernet traffic (by either sending an email or starting an FTP session, etc),
the router will dial the CDPD modem and establish a PPP connection. The CDPD Modem will supply the
router with its IP address, virtually becoming the router’s Internet Service Provider (ISP).
Frame
Relay
3
1
2
Internet
Local
CDPD
Network
Other
CDPD
Networks

AirLink Application Notes
AirLink Communications Page 5www.airlink.com
Diagram of how to connect the IP5200 Router and CDPD modem:
4. IP5200 Configuration
Setting up the IP5200 should be done using the instructions provided by DCB. The DIP Switches
on the Ethernet side of the unit are used for handshake and flow control and should be set as follows:
The following screen shots cover the device settings specific to connecting to a CDPD Modem.
192.168.1.101
Ethernet
Crossover
Cable
RS232
192.168.1.100
166.x.x.1
166.x.x.1
IP Address of CDPD Modem becomes Public Side
Address of Router during PPP negotiations.
IP5200 is both a Dial
-
on
-
Demand
Router and Network Firewall
Private Class
-
C IP Addresses are on same
subnet using subnet mask 255.255.255.0.
At the ‘
W
We el lc co om me e t to o S Se et tu up p
’ page,
select the ‘Internet Access’
button. The Configure bu
tton
takes you to the Main Menu.
10
100
RJ
-
45
1 2 3 4 5
Power
Jack ££¤¤¤

AirLink Application Notes
AirLink Communications Page 6www.airlink.com
You will need to set the Internet
Account,
LAN Settings, and
Dial-out Modem parameters.
The Internet Access se
tup
screen for Ports 1 and 2 has
three requirements:
-‘Enable’ must be checked
-Tel-1 and Tel-2 should be
entered as shown
-Disconnect after Idle Time
should be set to ‘0’.
This will make sure the
IP5200 does not drop the
PPP connection when the
serial port is idle.
Multi
-
port Usage
Even though the
IP5200’s (2) serial
ports can be used for
Multi-
link PPP, this is
not a feature that can
be used over CDPD
network.

AirLink Application Notes
AirLink Communications Page 7www.airlink.com
LAN Configuration is actually
referring to the Ethernet Port.
The LAN IP Address needs to be
different from the PLC address, but on
the same network and using the same
Net Mask.
You will need to supply your own DNS
Settings. You can get these from your
CDPD carrier.
Since there is no actual
Internet Account when
connecting to a CDPD
Modem, you can leave the
User Name, Password, and IP
Address allocated by ISP left
blank.
DNS should be the same as
entered on the previous
screen.
No Script File is needed.

AirLink Application Notes
AirLink Communications Page 8www.airlink.com
Select the Modem option.
Selecting the ‘Properties’ button
will take you to the Modem
Properties screen.
The Modem setup screen has four
requirements:
-Initial String should be ‘AT’
-Serial Line Speed = 19200
-Dial Type = Other
-Dial String = ‘ATDT’
-Auto-answer commands are N/A
-Select ‘Save as Other’

AirLink Application Notes
AirLink Communications Page 9www.airlink.com
The Advanced Menu has a great
many fea
tures, most of which do
not apply to this application.
Most of these settings deal with the
firewall functions inside the
IP52000. Since there is only one
device on the Ethernet port, and it is
connected to a CDPD Modem, and
not an ISP, the firewall is no
t really
necessary.
To put the Ethernet port outside the
IP5200, you must set the device up
as an Exposed Computer.
Select Enable Exposed
Computer Feature and
enter the IP of the Ethernet
device. In this case it is
192.128.1.101.

AirLink Application Notes
AirLink Communications Page 10 www.airlink.com
Checking to see if the
router works is easy.
Go to the Port Status page
on the Main Menu and
Select the Dial-Up
button.
You can watch the Log for
entries and errors, and see
the Physical Link and PPP
Link st
atus right on the
screen.
You know right away if the
connection to the modem is
working or not.

AirLink Application Notes
AirLink Communications Page 11 www.airlink.com
5. AirLink Raven CDPD Modem Configuration
The following are the proper S-Register configurations for the AirLink Raven CDPD Modem when
connecting to the IP5200 for making a PPP connection. These settings can be made using Wireless ACE.
CDPD Parameters:
[S110] Device Port=12345
[\N] Side Preference=3
[S116] Service ID Preference=3
[S111] Service ID=0/0/0
[S112] Channel List Mode=2
[S113] Channel List=0,0,0,0,0
[3W] 3 Watt Booster Support=0
[*DSIDE] Disable Side Switch=0
[*CTSE] CTS CDPD Enable=0
[#X] Serial Debug Output=0
Connection Parameters:
[S0] TCP Auto Answer Mode=0
[S7] TCP Establishment Timeout=20
[S50] Data Forwarding Timeout=1
[S51] Data Forwarding Character=0
[S53] Destination IP Address=10.0.10.0
[S53] Destination TCP/UDP Port=12345
[S53] Destination Connect Mode=T
[S210] AT Command Compatibility=1
[S211] Ignore DTR=0
[MD] Startup Mode Default=0
[MD] UDP Mode Default=0
[S60] Telnet Echo Mode=0
[S82] UDP Half Open Mode=0
[S83] UDP Half Open Timeout=5
[AIP] Allow Any UDP IP=1
[HOR] UDP Half Open Response=1
[S220] Break On TCP Connect=0
[S221] Delay Connect Response=0
[E] Command Echo=1
[V] Command Response Mode=1
[Q] Quiet Mode=0
[X] Call Progress Result Mode=0
[TCPT] TCP Inactive Timeout=1
[TCPS] Specify TCPT in Seconds=0
[TCPX] Allow TCP Suspension=0
[*DATZ] Disable Reset on ATZ=0
[*ENQ] Enable ENQ on TCP Connect=0
[DAE] Disable AT Esc Sequence=0
[RKEY] Radio Transceiver Keying=0
[IPL] IP List Dial=0
[*DU] Dial UDP Always=0
COM Port Parameters:
[\Q] Flow Control=2
[S23] Baud Rate=19200
[S23] Data Bits=8
[S23] Parity=N
[S23] Stop Bits=1
Modbus Parameters: N/A Friends List: (Optional)