Airlink101 USB 2.0 Ethernet Adapter ASOHOUSB User manual

USB 2.0 Ethernet Adapter
Model # ASOHOUSB
User’s Manual
Ver. 1A

Table of Contents
Introduction.........................................................................................3
Package Contents...........................................................................3
Features..........................................................................................3
System Requirements.....................................................................3
Installation.......................................................................................... 4
Windows 98SE................................................................................4
Windows ME ................................................................................... 7
Windows 2000.................................................................................9
Verify Driver Installation....................................................................12
Technical Support ............................................................................14

Introduction
The USB 2.0 Ethernet Adapter is a high performance and highly integrated USB
2.0 bus Ethernet Controller with embedded 7K*16 bit SRAM. The Adapter
supports both 10 Mbps and 100 Mbps Ethernet function based on IEEE802.3
and IEEE802.3u LAN standard.
Package Contents
•USB 2.0 Ethernet Adapter
•Driver CD
•Quick Installation Guide
Features
•Compliant with BOTH the Standard Specification of USB 2.0 and USB 1.1
•Compatible with IEEE 802.3u 100 BASE-T, TX, and T4
•Single chip USB to 10/100 Mbps Fast Ethernet Controller
•Supports BOTH bus or self powered mode
•Embedded 7K*16 bit SRAM, 256*16 bit SRAM and 8 FIFO
•Supports both full-duplex or half-duplex operations
•Provides a MII port for both Ethernet and PHY interface
•Supports suspended mode and remote wake-up (link-up or magic packet)
•PHY power down mode for power saving
•External PHY loop-back diagnostic capability
System Requirements
•IBM compatible Pentium-233MHZ or faster
•64 MB RAM or more
•Available USB 2.0 Port
•Systems with OS: MS Windows 98SE / ME / 2000 / XP

Installation
Windows 98SE
Step 1 Power on your computer and connect the USB 2.0 Ethernet Adapter to your
computer’s USB port.
Step 2 Insert the Driver CD into your CD drive.
Step 3 If the autorun screen appears, click Exit to close the autorun screen.
Step 4 Click Next at the Add New Hardware Wizard.

5
Step 5 Select Search for the best driver for your device (Recommended) and click
Next.
Step 6 Check on the Specify a location check box and click Browse.

6
Step 7 Expand the CD drive and select the Win98_ME folder and click OK.
Step 8 Click Next to install the driver.
Step 9 Insert Windows 98SE CD when prompted to do so and click OK.
Step 10 Click Finish to complete the installation.
Step 11 Connect an Ethernet cable from the USB 2.0 Ethernet Adapter to the desired
Ethernet device.
Step 12 Restart your computer.

7
Windows ME
Step 1 Power on your computer and connect the USB 2.0 Ethernet Adapter to your
computer’s USB port.
Step 2 Insert the Driver CD into your CD drive.
Step 3 If the autorun screen appears, click Exit to close the autorun screen.
Step 4 Select Specify the location of the driver (Advanced) and click Next.
Step 5 Check on the Specify a location check box and click Browse.
Step 6 Expand the CD drive and select the Win98_ME folder and click OK.

8
Step 7 Click Next to install the driver.
Step 8 Click Finish to complete the installation.
Step 9 Connect an Ethernet cable from the USB 2.0 Ethernet Adapter to the desired
Ethernet device.
Step 10 Restart your computer.

9
Windows 2000
Step 1 Power on your computer and connect the USB 2.0 Ethernet Adapter to your
computer’s USB port.
Step 2 Insert the Driver CD into your CD drive.
Step 3 If the autorun screen appears, click Exit to close the autorun screen.
Step 4 Click Next at the Found New Hardware Wizard.

10
Step 5 Select Search for a suitable driver for my device (recommended) and click
Next.
Step 6 Click Browse, expand the CD drive, select Win2000 folder and click OK.

11
Step 7 Click Next to install the driver.
Step 8 Click Yes at the Digital Signature prompt.
Step 9 Click Finish to complete the installation.
Step 10 Connect an Ethernet cable from the USB 2.0 Ethernet Adapter to the desired
Ethernet device.
Step 11 Restart your computer.

12
Verify Driver Installation
To verify if the driver has been installed successfully, please perform the following steps.
Step 1 Right-click on My Computer from your desktop and select Properties.
Step 2 Select the Hardware tab and click on Device Manager.

13
Step 3 Expand Network adapters from the list and verify that ASIX ax88772 USB2.0
to Fast Ethernet Adapter is listed and no yellow question mark is beside it.
Congratulations! You have successfully installed the USB 2.0 Ethernet
Adapter.

14
Technical Support
E-mail: [email protected]
Toll Free: 1-888-746-3238
Web Site: www.airlink101.com
*Actual throughput will vary. Network conditions and environmental factors lower actual throughput rate.
Copyright © 2005 AirLink101. All rights reserved. AirLink101, the stylized AirLink101 logo, specific
product designations, and all other words and logos that are identified as trademarks and/or service
marks are, unless noted otherwise, the trademarks and service marks of AirLink101. All other product or
service names are the property of their respective holders. AirLink101 products are protected under
numerous U.S. and foreign patents and pending applications, mask work rights, and copyrights.