Airlink101 AWLL4030 User manual

Ver. 1A
PackageContents:
•SuperGUSB2.0Adapter
•USB2.0ExtensionCable
•Installation CD
•Quick Installation Guide
Note: Wheneverthe FoundNew HardwareWizard appears,click Cancel toquit
the wizard and continue with the installation.
Step 1 Insert the Wireless USBAdapter to the computer’s USB port.
Step 2 Insert theInstallation CDinto theCD drive andwait forthe autorunscreen
toappear.
Note: If the autorun screen doesn’t appear automatically go to Start, Run, and
type D:\autorun.exe (where D is the letter of your CD drive) and click OK.
Section 1
Installation
Quick Installation Guide
Model#AWLL4030
Super G Wireless USB 2.0 Adapter
The following steps are for Windows 2000/XP. Please refer to the User’s
Manual on the provided CD for Windows 98SE/ME.
For Windows 2000/XP, you must update your USB driver to USB 2.0
For Windows XP you must install Service Pack 2 prior to installing the USB
Adapter.
Step 4 Click Next at the welcome screen.
Step 3 Click Install Driver (Windows 2000/XP).

Continue on back...
ContinueonBack
Step 5 Click Next to accept the LicenseAgreement.
Step 6 Verify Install Client Utilities and Driver is selected and click Next.
Step 7 Click Yes to acknowledge the need for a reboot after the installation.
Step 8 Click Next to accept the default Destination Folder.
Step 9 Click Next to accept the default Program Folder.
Step 10 Read the notes carefully and click Next.
Step 11 Verify Atheros Client Utlity and Supplicant is selected and click Next.
Step 12 Click OK to acknowledge the prompt.

Section 3
Step 13 Click Continue Anyway at the Windows Logo prompt for the Bootloader
Download.(ClickYes forWindows2000).
Step 14 Click Continue Anyway at the Windows Logo prompt for the Wireless
NetworkAdapter (ClickYes forWindows2000).
Step 15 Click OK to reboot your computer.
Section 2
Configure USB Adapter
Step 1 Start the Atheros Client Utility by double-clicking on it from your desktop.
Step 2 If there is no Signal Strength and/or the IPAddress is all 0’s, select the
Profile Managment tab.
The following steps are for Windows 98SE/ME/2000/XP.
If you already have signal strength and valid IP address, you do not need
to perform the following steps.

E-mail:[email protected]
TollFree:1-888-746-3238
WebSite:www.airlink101.com
Section 3
Technical Support
Section 4
Step 3 Select the Default profile and click Modify.
Copyright©2005AirLink101.Allrightsreserved.AirLink101,thestylizedAirLink101logo,specificproductdesignations,andallotherwords
andlogosthatareidentifiedastrademarksand/or service marks are, unless notedotherwise,thetrademarksandservicemarksofAirLink101.
Allotherproductorservicenamesarethepropertyoftheirrespectiveholders.AirLink101 products are protected under numerous U.S. and
foreignpatentsandpendingapplications,maskworkrights,andcopyrights.
*TheoreticalmaximumwirelesssignalratebasedonIEEEstandard802.11gspecifications.Actualdatathroughputwillvary.Networkconditions
andenvironmentalfactors,includingvolumeofnetworktraffic,buildingmaterialsandconstruction,mixofwirelessproductsused,radio
frequencyinterference(e.g.,cordlesstelephonesandmicrowaves)aswell as network overhead lower actual datathroughputrate.
Step 4 Enter the SSID (Network Name) that your wireless router/access point is
using in the SSID field and click OK.
Step 5 Return to the Current Status tab and verify that you have signal strength
andvalid IPaddress.
If your wireless router/access point has encryption enabled, you’ll need to apply
the same encryption settings to theAdapter as well. For information on how to
configureencryption, pleaserefer tothe User’sManual inthe suppliedInstallation
CD.