AirLive DS-100 v2 User manual

DS
-
100
v2
Signal
bridge between RJ
-
45 and
RS-232
User’s Manual
Version 1.0

Copyright and Disclaimer
AirLive DS-100 v2 User’s Manual
Version 1.0
This guide is written for initial firmware version or later.
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please
use with caution. All information is subject to change without notice
All Trademarks are properties of their respective holders.

Table of Contents
AirLive DS-100 v2 User’s Manual
1
Table of Contents
1. Introduction.............................................................................................. 1
1.1 Overview............................................................................................ 1
1.2 How to Use This Guide...................................................................... 3
1.3 Firmware Upgrade and Tech Support ................................................ 4
1.4 Features ............................................................................................ 5
2. Installing the Device Server .................................................................... 6
2.1 Before You Start................................................................................. 6
2.2 Package Content ............................................................................... 6
2.3 Knowing your DS-100 v2 ................................................................... 6
2.3.1 LED Indicator...............................................................................................7
2.3.2 Keypad ........................................................................................................8
2.3.3 Connector Indicator .....................................................................................9
2.4 Hardware Installation ....................................................................... 10
3. Configuring the Device Server.............................................................. 12
3.1 Important Information....................................................................... 12
3.2 Prepare your PC.............................................................................. 12
3.3 Management Interface..................................................................... 13
3.4 Introduction to Web Management .................................................... 13
3.4.1 Welcome Screen and Login.......................................................................13
3.5 Introduction to Web Management .................................................... 14
3.5.1 Getting into Web Management ..................................................................14
4. Web Management in Device Server...................................................... 15
4.1 About the Menu Structure ................................................................ 15
4.2 System Configuration ...................................................................... 16
4.2.1 DS-100 v2 Configuration ...........................................................................16
4.2.2 Gateway/Controller....................................................................................18
4.2.3 Operation Instructions................................................................................23
5. Troubleshooting .................................................................................... 24
6. Specifications ........................................................................................ 30
7. Network Glossary .................................................................................. 32

1. Introduction
AirLive DS-100 v2 User’s Manual
1
11. Introduction
1.1 Overview
Whether you are “operating a wireless hotspot service for generating revenue” or “providing
free but controlled wireless internet access to guests”, it would be handy to both the
operators and the wireless users if the account information (such as username, password,
SSID and etc.) can be readily output to POS printers and printed out as account tickets.
DS-100 v2 is designed specifically to operate in conjunction with specific Controllers
/Gateways. Typical serial POS printers on the market today may or may not be
IP network ready, and it is not practical to integrate each brand one-by-one with Controllers
/Gateways. Hence, it has specifically designed a smart device server – DS-100 v2, for two
purposes:
1. Attaching before a serial POS printer so that one or more POS printers can be
connected to a Controller/Gateway via IP networks.

1. Introduction
AirLive DS-100 v2 User’s Manual
2
2. Pre-integrated with the Controller/Gateway so that account generation becomes quick
and easy to the operator, simply by a push of buttons on the device.
It provides DS-100 v2 and a POS printer as a combo set called Network Ticket Generator.
The followings are typical application scenarios:
A small business who wishes to quickly set up a wireless service hotspot for charged
Internet service may purchase a Gateway, and a Network Ticket Generators set. The
Gateway alone serves as an AP and a gateway, Network Ticket Generator enables the
registration operator to generate and issue accounts via push buttons on the DS-100 v2
and hand out the account ticket printed out by POS printer.
A corporate has several sites. Deployed at the reception area of each site are with a
DS-100 v2 and a POS printer. Guests who need wireless connection to the internet simply
need to request the receptionist and obtain a slip with account information. The guest
account will automatically expire after the pre-configured time.
A hotel has a Controller/Gateway and multiple APs within its hospitality areas. Multiple sets
of Network Ticket Generator are distributed at the service desks and lounge counters. The
service clerks are able to create accounts for their guests with charged or free internet
service depending on the hotel’s service model.
Below are two network diagrams examples using Network Ticket Generator combo set.
(1) One Gateway with one Network Ticket Generator set.
(2) One Gateway with multiple Network Ticket-Generator sets.

1. Introduction
AirLive DS-100 v2 User’s Manual
3
*Note:
The POS printer has an individual manual, therefore, its configuration details is not covered
in this guide.
Though DS-100 v2 is specifically designed to for on-demand account generation and
operate POS printers, it can also be deployed independently to connect other RS232
devices to an Ethernet network for remote operation. If you will be deploying DS-100 v2
independently to manage other serial devices, please carefully set the Serial Settings in
DS-100 v2 to match the operating needs of your serial device.
*Note:
If you connect other serial device to DS-100 v2 and are unable to remotely operate your
connected serial device, please check that:
The settings under Serial Settings of DS-100 v2 are configured to match your serial device
operating requirements.
If your serial device application operates on pure serial communication then you need to
setup a COM port redirector.
1.2 How to Use This Guide
Recommended Reading
Chapter 1:
This chapter explains the basic information for DS-100 v2. It is a must read.
Chapter 2:
This chapter is about hardware installation. You should read through the entire
chapter.

1. Introduction
AirLive DS-100 v2 User’s Manual
4
Chapter 3:
 3.1 Important Information:
This section has information of default setting such as IP, Username, and
Password.
 3.2 Management Interface:
This section introduces Web management.
 3.3 Introduction to Web Management:
 This section tells you how to get into the Web UI using HTTP.
Chapter 4:
This chapter explains all of the management functions via Web management.
Chapter5:
This chapter shows technical specification of DS-100 v2.
Chapter 6:
Explanation on network technical terms from A to Z. Highly recommended for
reference when you encounter an unfamiliar term.
1.3 Firmware Upgrade and Tech Support
If you encounter a technical issue that cannot be resolved by information on this guide, we
recommend that you visit our comprehensive website support at www.airlive.com. The tech
support FAQ are frequently updated with latest information.
In addition, you might find new firmwares that either increase software functions or provide
bug fixes for DS-100 v2. You can reach our on-line support center at the following link:
http://www.airlive.com/support/support_2.jsp
Since 2009, AirLive has added the “Newsletter Instant Support System” on our website.
AirLive Newsletter subscribers receives instant email notifications when there are new
download or tech support FAQ updates for their subscribed airlive models. To become an
AirLive newsletter member, please visit: http://www.airlive.com/member/member_3.jsp

1. Introduction
AirLive DS-100 User’s Manual
5
1.4 Features
 1 x 10/100Mbps RJ-45 port + 2 x RS-232 DB9 Serial port
 Trigger the Built-in On-Demand Billing Plan inside the M-series Controller
 Web Management via web browser
 7 Segment LED display
 6 Matrix function keys
 Up to 921.6 Kbps baud rate supported
 Ethernet activity, Power LED's
 Monitor, manage and control industrial field devices remotely
 Support TCP Server/ Client link mode
 DHCP, BOOTP, Static IP, and ARP supported
 Over Voltage Protection
 Wide Voltage Support
 Wall-mount Rugged metal case with IP50 compliance for industrial usage
 Provide Screw Terminal Block

2. Installing the Device Server
AirLive DS-100 v2 User’s Manual 6
2 2. Installing the Device
Server
This chapter describes the hardware features and the hardware installation procedure for
the DS-100 v2. For software configuration, please go to chapter 3 for more details.
2.1 Before You Start
It is important to read through this section before you install the DS-100 v2.
 The maximum cabling distance is 100 meters.
 Make sure that the connection between DS-100 v2 and PC/NB is well established
 Always check the LED lights for troubleshooting
2.2 Package Content
Unpack the contents of the DS-100 v2 and verify them against the checklist below.
 One unit of DS-100 v2
 12V/1A Power Adapter
 Quick Installation Guide
Compare the contents of your DS-100 v2 package with the standard checklist above. If any
item is missing or damaged, please contact your local dealer for service.
2.3 Knowing your DS-100 v2
Below are descriptions and diagrams of the product:

2. Installing the Device Server
AirLive DS-100 v2 User’s Manual
7
2.3.1 LED Indicator
The LED Indicators gives real-time information of systematic operation status. The
following table provides descriptions of LED status and their meaning.
LED Description
Power On: Power on.
Off: Power off.
Status
 On: The device associated with Hotspot.
 Off: The device unassociated with Hotspot.
 Flash: The FUNCTION key activated.
Lock
 On: The Keypad locked;
 Off: The Keypad unlocked;
 Flash: Input digit number key for unlocking.
Link/Act Link and activity of Ethernet port
100M : Link speed of Ethernet port.

2. Installing the Device Server
AirLive DS-100 v2 User’s Manual 8
2.3.2 Keypad
Keypad Description
PRE (-) /POS (+)
There are two functions:
 Increase (POS) and Decrease (PRE) number for selecting
Plan or Function option.
 Reset to factory default: Press and Hold two button for
more than 5 seconds (until Status LED FLASH) to reset the
device to default configurations.
Enter (►) Click to print On-Demand Account Tickets or Function
selected.
Function ( )
 Lock Keypad: Press and Hold button until Lock LED ON.
 Unlock Keypad: Press button until Lock LED FLASH, then
input key for unlocking.
 Lock Keypad: Press and Hold button until Lock LED ON.
 Link Test: Click button and then select number 1 then click
Enter.
 Statement Printing: Click on this button, it will print out
account balance according press the numbers.
I. Current Balance: Select Number 9 and clicks Enter, it
will print out current balance.
II. Early Balance: Select Number 8 and clicks Enter, it will
print out early balance.
CANCEL (X)
 Stop to print Statement.
 Clear input key for unlocking.
 Cancel other event
REPEAT (R) Repeat to print previous Tickets.
Keypad

2. Installing the Device Server
AirLive DS-100 v2 User’s Manual
9
*Note: The Lock/Unlock function, please refer to Chapter 5 for more detail installation.
2.3.3 Connector Indicator
Top Panel
Connector Description
DC Power Jack (12V/1A)
The power socket for connecting to an external
power source through the power adapter provided in
the package.
Screw Terminal Block For DC Power input, please refer to Chapter 5 for
more detail information.
Reset Button For reboot only.
Ethernet Port Ethernet port for connecting to a hotspot gateway.
Bottom Panel

2. Installing the Device Server
AirLive DS-100 v2 User’s Manual 10
Connector Description
COM 1 Serial Port for connection with a POS printer.
COM2 Serial Port for connection with a POS printer. Used
for back up when COM 1 malfunctions.
2.4 Hardware Installation
The following diagram illustrates how to connect DS-100 v2 to the POS printer and
Gateways/Controllers. Please follow the steps described below to install hardware:
(1) Attach DS-100 v2 to a power source, either through adaptors provided in the package or
through DC socket with a DC power supply.
(1) Attach POS printer to a power source, through adaptors provided in the package and
turn on the power switch situated on the left side of the device.
(2) Connect POS printer to the COM1 port of DS-100 v2 by a RS-232 cable provided within
POS printer package.
(3) Connect DS-100 v2 to the LAN port of your Gateway/Controller by an Ethernet cable.

2. Installing the Device Server
AirLive DS-100 v2 User’s Manual
11
*Note: You need to connect to the correct LAN port if your Gateway/Controller is operating
in Port-based mode.
A. Make sure mounting surface on the bottom of the DS-100 v2 is grease and dust free.
B. Remove adhesive backing from your Rubber Feet.
C. Apply the Rubber Feet to each corner on the bottom of the DS-100 v2. These footpads
can prevent the Switch from shock/vibration.

3. Configuring the Device Server
AirLive DS-100 v2 User’s Manual 12
DS-100 v2 is designed specifically to operate in conjunction with all Gateways/Controllers.
If you are not using default settings, before connecting DS-100 v2 to your
Gateway/Controller, some configurations steps are required. The configuration instructions
for Gateways/Controllers and DS-100 v2 are covered in the following sections.
3.1 Important Information
The following information will help you to get start quickly. However, we recommend you to
read through the entire manual before you start. Please note the username and password
are case sensitive.
 The default IP address is: 192.168.1.10
 Subnet Mask: 255.255.255.0
 The default Gateway is: 192.168.1.254
3.2 Prepare your PC
The DS-100 v2 can be managed remotely by a PC through RJ-45 cable. The default IP
Address of the DS-100 v2 is 192.168.1.10 with a subnet mask of 255.255.255.0. This
means the IP address of the PC should be in the range of 192.168.1.2 to 192.168.1.253 (do
not include 192.168.1.10).
To prepare your PC for management with the DS-100 v2, please do the following:
1. Connect your PC directly to the copper port of DS-100 v2
2. Set your PC’s IP address manually to 192.168.1.100 (or other address in the same
Subnet)
3 3. Configuring the Device
Server

3. Configuring the Device Server
AirLive DS-100 v2 User’s Manual
13
You are ready now to configure the DS-100 v2 by using your PC.
3.3 Management Interface
The DS-100 v2 can be configured using on the Web management interfaces.
 Web Management (HTTP): You can manage your DS-100 v2 by simply typing its IP
address in the web browser. Most functions of DS-100 v2 can be accessed by web
management inter face. We recommend using this interface for initial configurations.
To begin, simply enter DS-100 v2’s IP address (default is 192.168.1.10) on the web
browser.
3.4 Introduction to Web Management
3.4.1 Welcome Screen and Login
The DS-100 v2 offers Web Management interfaces for users. Users can easily access and
control DS-100 v2 via web browsers. The Web-Based Management supports Internet
Explorer 5.0. It is based on Java Applets with an aim to reduce network bandwidth
consumption, enhance access speed and present an easy viewing screen.

3. Configuring the Device Server
AirLive DS-100 v2 User’s Manual 14
3.5 Introduction to Web Management
We recommend users to browse through DS-100 v2’s web management interface to get an
overall picture of the functions and interface. Below are the recommended initial
configurations for first time login:
*Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. The
user has to explicitly modify the browser setting to enable Java Applets to use network
ports.
3.5.1 Getting into Web Management
Web Management (HTTP)
1. Launch the Internet Explorer.
2. Type http://192.168.1.10/setting.htm , and then press “Enter”.
3. The home screen of the Web-based management appears.

4. Web Management in Device Server
AirLive DS-100 v2 User’s Manual
15
In this chapter, we will explain all settings in web management interface. Please be sure to
read through Chapter 3.4’s “Introduction to Web Management” first.
4.1About the Menu Structure
The web management menu of DS-100 v2 is divided into 4 parts: Serial Settings, Network
Settings and Firmware Upgrade.
COM1 Setting(Serial Settings corresponding to POS printer)
Data Baud Rate Select the desired baud rate. (The number of
characters per second transferred)
Data Bits Select the number of bits in each character.
4 4. Web Management in
Device Server

4. Web Management in Device Server
AirLive DS-100 v2 User’s Manual 16
Data Parity Choose between Even or Odd for error detection, or
select None for no error detection.
Stop Bits Choose the number of stop bits to be sent at the end of
every character. Electronic devices usually use 1 bit,
slower electromechanical devices use 1.5 bit.
Flow Control Choose the method of flow control to pause and resume
the transmission of data to coordinate with printer speed.
Select None if flow control is not required.
Network Settings
Static IP Address The static IP address assigned to DS-100 v2.
Static Subnet Mask The subnet mask of DS-100 v2.
Static Default Gateway The default gateway of DS-100 v2.
Static DNS Server Set the DNS server used by DS-100 v2.
Transmit Timer TCP transmit timer, set the desired value or use default
value. When the timer expires for a sent packet, sender
will retransmit the packet.
Server Listening Port Set the port number for communication with the
Gateway/Controller.
Firmware Upgrade Upgrade firmware from remote-PC via Ethernet.
4.2System Configuration
DS-100 v2 is designed specifically to operate in conjunction with all Gateways/Controllers.
If you are not using default settings, before connecting DS-100 v2 to your
Gateway/Controller, some configurations steps are required. The configuration instructions
for Gateways/Controllers and DS-100 v2 are covered in the following sections.
4.2.1DS-100 v2 Configuration
DS-100 v2 supports web based configuration. By factory default, DS-100 v2 web interface
can be accessed with
IP address: 192.168.1.10
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.254
Step1: Configure administrator PC’s TCP/IP settings with a static IP address that is under
the same subnet mask as DS-100 v2. For example: 192.168.1.100

4. Web Management in Device Server
AirLive DS-100 v2 User’s Manual
17
Step2: Attach DS-100 v2 to a power supply using the adapter provided in the package.
Connect the administrator PC to the Ethernet Port of DS-100 v2 via an Ethernet
cable. Launch a web browser and type in the default IP address of DS-100 v2 in
the address field (http://192.168.1.10/setting.htm ), the web interface of DS-100
v2 should appear.