AirLive SA-102 User manual

SA-102
Smart In Wall Dual Switch
User Manual

Copyright and Disclaimer
iAirLive SA-102 User Manual
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
This product contains some codes from GPL. In compliance with GPL agreement,AirLive
will publish the GPL codes on our website. Please go to www.airlive.com and go to the
"Support->GPL" menu to download source code.
All Trademarks are properties of their respective holders.

Copyright and Disclaimer
AirLive SA-102 User Manual ii
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Warning
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities. Contact your local government for information regarding the collection
systems available. If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging your
health and well-being.
When replacing old appliances with new once, the retailer is legally obligated to take back
your old appliance for disposal at least for free of charge.
Disposal
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for
environmental safe recycling.

Table of Contents
AirLive SA-102 User Manual
iii
Table of Contents
1. Overview................................................................................................... 1
1.1 Adding to Z-WaveTM Network ........................................................... 1
1.2 Auto Inclusion.................................................................................... 2
1.3 LED Indication................................................................................... 3
1.4 Choosing a Suitable Location ............................................................ 3
1.5 Installation ......................................................................................... 4
1.6 Programming..................................................................................... 4
1.7 Troubleshooting............................................................................... 19
1.8 Specification .................................................................................... 20

1. Overview
AirLive SA-102 User Manual
1
1
1.
Overview
This in-wall dual relay switch module is a transceiver which is a Z-Wave PlusTM enabled
device and is fully compatible with any Z-WaveTM enabled network. Mini size design let the
module can easily hide itself into the wall box and that will be good for the house
decoration.
There are many kind of application by using the module to switchAC power on and off, one
main application is the light control. The new smart relay calibration technology can reduce
the inrush current caused by the load and let the module work perfectly with many kind of
light like incandescent, fluorescent and LED light.
This in-wall switch module is able to detect Instant power wattage and overload current
(7.5Awith resistive load) of connected light or appliances. When detecting overload state,
the Module will be disabled and its On/Off button will be lockout of which LED will flash
quickly. However, disconnect and re-connect the Module will reset its overload condition to
normal status.
1.1 Adding to Z-WaveTM Network
In the front casing, there is an on/off button with LED indicator below which is used to toggle
switch on and off or carries out inclusion, exclusion, reset or association. When first power
is applied, its LED flashes on and off alternately and repeatedly at 0.5 second intervals. It
implies that it has not been assigned a node ID and start auto inclusion.

1. Overview
AirLive SA-102 User Manual
2
1.2 Auto Inclusion
The function of auto inclusion will be executed as long as the in wall switch does not have
Node ID and just connect the switch to main power.
Note: Auto inclusion timeout is 2 minute during which the node information of explorer
frame will be emitted once every several seconds. Unlike “inclusion” function as shown in
the table below, the execution of auto inclusion is free from pressing the On/Off button on
the Switch.
The table below lists an operation summary of basic Z-Wave functions. Please refer to the
instructions for your Z-WaveTM Certificated Primary Controller to access the Setup function,
and to include/exclude/associate devices.
Function
Description
Annotation
No node ID
The Z-Wave Controller does not
allocate a node ID to the Switch.
LED 2
-second on, 2-second
off
Inclusion
1. Put your Z-Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
One press one flash LED
Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
inclusion mode.
Exclusion
Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the
One press one flash LED
Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
exclusion mode.
Node ID has been excluded.
LED 0.5s On, 0.5s Off
(Enter auto inclusion)
Reset
Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
inclusion mode.
Use this procedure only in the
event that the primary controller is
lost or otherwise inoperable.
Within 1 second,press On/Off
button again for 5 seconds.
IDs are excluded.
LED 0.5s On, 0.5s Off
(Enter auto inclusion)

1. Overview
AirLive SA-102 User Manual
3
Association
The SA-102 is an always listening
Z-Wave device, so associations be
added or removed by a controller at
any time.
Or If your controller requires to have
the SA-102 send a 'node information
frame' or NIF for associations,
pressing the On/Off button three times
within 2 seconds will cause the
SA-102 to send its NIF.
LED one press one flash
There are 3 groups for the switch
•Including a node ID allocated by Z-Wave Controller means inclusion.
Excluding a node ID allocated by Z-Wave Controller means exclusion.
•Failed or success in including/excluding the node ID can be viewed from the
Z-Wave Controller.
Sometimes people are not easy to execute exclusion or inclusion especially when SA-102
already installed in a wall box. To solve this issue, SA-102 support a special feature that
can use S1 or S2 to execute “exclusion, inclusion, Reset orAssociation” at the first 3
minutes when first time connect to main power.
1.3 LED Indication
To distinguish what mode the switch is in, view from the LED for identification.
State Type
LED Indication
Normal
Whatever we switch On and off of the SA-102 by S1 S2 or On/Off button or RF
command, the LED will ligh
ts up 1 second and then off.
No node ID
Under normal operation, when the Switch has not been allocated a node ID,
the LED flashes on and off alternately at 2
-second intervals. By pressing S1
S2 or On/Off button, it will stop flashing temporarily.
Learning
When SA-102 is in learning mode, LED flashes on and off alternately and
repeatedly at 0.5 second intervals.
Overload
When overload state occurs, the Switch is disabled of which LED flashes on
and off alternately at 0.2 second intervals. Overload state c
an be cleared by
disconnect and reconnect the Switch to the main power
1.4 Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
3. Do not locate the Switch where exists combustible substances or any source of
heat, e.g. fires, radiators, boiler etc.

1. Overview
AirLive SA-102 User Manual
4
4. After putting it into use, the body of Switch will become a little bit hot of which
phenomenon is normal.
1.5 Installation
1. Put the in wall switch into a wall box and connect the AC power wire L, N to in wall
switch connector L, N.
2. Connect the wall switch to the SA-102 as picture.
3. To manually turn ON the Switch, press and release the On/Off button. The LED will
light ON for 1 second, and the load plugged into the Switch will also turn ON.
4. To manually turn OFF the Switch, simply press and release the On/Off button. The
LED will light ON for 1 second and the load plugged into the Switch will turn OFF.
1.6 Programming
1.6.1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY SWITCH commands that are part of the
Z-Wave system.
1. BASIC_GET / BINARY_SWITCH_GET
Since the switch have two relay, the Switch will report its On/Off state to the Controller by
setting Configuration parameter 3.
Configuration parameter 3=1 Report ON when relay 1 ON
Report OFF when relay 1 OFF
Configuration parameter 3=2 Report ON when relay 2 ON
Report OFF when relay 2 OFF

1. Overview
AirLive SA-102 User Manual
5
Configuration parameter 3=3 (default) Report ON when either relay 1 ON or relay 2 ON
Report OFF when both relay 1 and relay 2
OFF
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF:
[Command Class Basic, Basic Report, Value = 0(0x00)]
Report ON:
[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch Binary Get]
Binary Switch Report Command:
Report OFF:
[Command Class Switch Binary, Switch Binary Report, Value =0(0x00)]
Report ON:
[Command Class Switch Binary, Switch Binary Report, Value
= 255(0xFF)]
2. BASIC_SET / SWITCH_BINARY_SET
Since the switch has two relay, the load attached to the Switch will turn on or off upon
receipt of the following commands from a Z-Wave Controller by setting Configuration
parameter 3.
Configuration parameter 3=1 switch ON and OFF of relay 1
Configuration parameter 3=2 switch ON and OFF of relay 2
Configuration parameter 3=3 (default) switch ON and OFF both relay 1 and relay 2
[Command Class Basic, Basic Set, Value = 1~99, 255(0xFF)]: the load attached to
the Switch turns on.
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to the Switch
turns off.
[Command Class Switch Binary, Switch Binary Set, Value = 1~99, 255(0xFF)]: the
load attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the load
attached to the Switch t
urns off.
1.6.2. Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to control associated Z-Wave devices. It supports 3
association groups which every group has one node support.
Group1~Group3 support SWITCH_BINARY_REPORT,
METER_REPORT_COMMAND_V3
For group 1, the Switch will report (1) ON/OFF status of Relay1 and Relay2 (2) Instant
Power Consumption (Watt) of Relay1 and Relay2 (3) Accumulated Power Consumption
(KWh) of Relay1 and Relay2 to Z-Wave Controller.
For group 2, the Switch will report (1) ON/OFF status of Relay1 (2) Instant Power

1. Overview
AirLive SA-102 User Manual
6
Consumption (Watt) of Relay1 (3) Accumulated Power Consumption (KWh) of Relay1 to
Z-Wave Controller.
For group 3, the Switch will report (1) ON/OFF status of Relay2 (2) Instant Power
Consumption (Watt) of Relay2 (3) Accumulated Power Consumption (KWh) of Relay2 to
Z-Wave Controller.
1.6.2.1. Auto report to Grouping 1 ~3 (Maximum Node 1)
1.6.2.1.1.On/Off Event Report
When “on” or “off” state has been changed, it will send Binary Switch Report to the nodes of
Group1~3.
Binary Switch Report
ON:[Command Class Switch Binary, Switch Binary Report, Value=255(0xFF)]
OFF:[Command Class Switch Binary, Switch Binary Report, Value=0(0x00)]
1.6.2.2. Instant Power Consumption vary over 5% report
When the power consumption of load vary over 5%, it will send Meter report to the nodes of
Group
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type = 0x01，Precision
= 1
，
Scale = 0x02
，
Size = 4
，
Meter Value(W) ]
1.6.2.3. Overload alarm report command
When SA-102 detect the overload, it will send Alarm Report to the correspond Group。
The content of Alarm Report
Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type = 0x08,
Alarm Level = 0xFF]
1.6.3. Response to Meter Get Command
The Switch will report its (1) instant Power Consumption (Watt) or (2) accumulated power
consumption (KWH) or (3) AC load Voltage (V) or (4) AC load current (I) (5) load power
factor (PF) to Z-Wave Controller after receive the Meter Get Command from Z-Wave
Controller.
1.6.3.1. Instant Power Consumption (Watt) of Switch
When receiving Meter Get Command, it will report Meter Report Command to the node
asked.