AirLive POE-GSH1816R-250 User manual

POE-GSH1816R-250
16 Port RJ45 with 2 Port SFP
Topology POE Switch
User Manual

Copyright and Disclaimer
AirLive POE-GSH1816R-250 User Manual
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
All Trademarks are properties of their respective holders.

Table of Contents
i AirLive POE-GSH1816R-250 User Manual
Table of Contents
1. Introduction..............................................................................................1
1.1 Overview..............................................................................................1
1.2 How to Use This Guide........................................................................2
1.3 Firmware Upgrade and Tech Support..................................................2
2. Installing the POE-GSH1816R-250.......................................................3
2.1 Before You Start...................................................................................3
2.2 Package Content.................................................................................3
2.3 Optional Accessory..............................................................................4
2.4 Knowing your POE-GSH1816R-250....................................................5
2.5 Hardware Installation...........................................................................5
2.6 LED Table ............................................................................................7
3. Introduce the POE-GSH1816R-250.........................................................9
3.1 Important Information...........................................................................9
3.2 Prepare your PC..................................................................................9
3.3 Management Interface.........................................................................9
3.4 Introduction to Web Management......................................................10
4. Web Management: System of POE-GSH1816R-250............................13
4.1 System...............................................................................................13
4.2 Port Management ..............................................................................53
4.3 PoE Management..............................................................................73
4.4 VLAN Management ...........................................................................81
4.5 Quality of Service.............................................................................104
4.6 Spanning Tree .................................................................................120
4.7 MAC Address Tables........................................................................123
4.8 Multicast...........................................................................................128
4.9 MVR.................................................................................................147
4.10 DHCP.............................................................................................151
4.11 Security..........................................................................................160

Table of Contents
AirLive POE-GSH1816R-250 User Manual
ii
4.12 Access Control...............................................................................227
4.13 Event Notification...........................................................................230
4.14 Diagnostics....................................................................................231
4.15 Maintenance..................................................................................236
5. Web Management: Device of POE-GSH1816R-250...........................246
5.1 Graphic Monitoring ..........................................................................246
5.2 Management....................................................................................251
5.3 Maintenance....................................................................................253
6. Trouble Shooting ...................................................................................257
6.1 Incorrect Connections......................................................................257
6.2 Cabling.............................................................................................258
7. Specifications.........................................................................................259
8. Network Glossary ..................................................................................262
8.1 Cabling.............................................................................................267

1. Introduction
1 AirLive POE-GSH1816R-250 User Manual
1
1.Introduction
1.1 Overview
The POE-GSH1816R-250 is a 16-port Gigabit TP L2 PoE switch with 2-
Port Gigabit
TP/SFP slots. This Switch can power on 802.3at/af cameras by RJ45 cable. Web-
based
management unit, associated with SNMP agent allow user access the switch remotely. In
addition, the switch features comprehensive and useful functions such as QoS, Spanning
Tree, VLAN, Port Trunking, Bandwidth Control, Por
t Security, SNMP/RMON, IGMP
Snooping capability via the intelligent software. Moreover, it build in the device manager
function to monitor , control AirLive Access Point and Cameras. Furthermore, topology view
function let system integrator or MIS to monit
or the Network environment easier. It is
suitable for IP cameras and VoIP applications.
Note:
The switch was for using indoor purpose, if it was used in outdoor environment or
connect with cable to outdoor then it must to use a lightning arrester to protect the
switch.

1. Introduction
AirLive POE-GSH1816R-250 User Manual
2
1.2 How to Use This Guide
POE-GSH1816R-250
is a SNMP and web smart PoE Switch with many functions. It is
recommended that you read through the entire user’s guide whenever possible. The user
guide is divided into different chapters. You sh
ould read at least go through the first 2
chapters before attempting to install the device.
Recommended Reading
Chapter 1: This chapter explains the basic information for POE-GSH1816R-250
. It is a
must read.
Chapter 2: This chapter is about hardware insta
llation. You should read through the
entire chapter.
Chapter 3:
3.1 Important Information
: This section has information of default setting such as
IP, Username, and Password.
3.3 Management Interface
: This section introduces Web management, and
Console management.
3.4 Introduction to Web Management
: This section tells you how to get into the
WebUI using HTTP.
1.3 Firmware Upgrade and Tech Support
If you encounter a technical issue that cannot be resolved by information on this guide, we
recommend that you visit our comprehensive website support at www.airlive.com
. The tech
support FAQ are frequently updated with latest information.
In addition, you might find new firmware’s that either increase software functions or pr
ovide
bug fixes for POE-GSH1816R-250. You can reach our web page
http://www.airlive.com/product/POE-GSH1816-250

2. Installing the POE-GSH1816R-250
3 AirLive POE-GSH1816R-250 User Manual
This chapter describes the hardware features and the hardware installation procedure for
the POE-GSH1816R-250. For software configuration, please go to chapter 3 for more
details.
2.1 Before You Start
It is important to read through this section before you install the POE-GSH1816R-250
The maximum cabling distance is 100 meters by Cat5e RJ45 cable.
Do not create a network loop.
Always check the LED lights for troubleshooting
2.2 Package Content
Unpack the contents of the POE-GSH1816R-250 Plus and verify them against the checklist
below.
One unit of POE-GSH1816R-250
Power Cord
Four Rubber Feet
User Guide (CD-ROM)
Quick Installation Guide
Rack-mounted Kit
2
2.Installing the
POE-GSH1816R-250

2. Installing the POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
4
Compare the contents of your POE-GSH1816R-250 package with the standard checklist
above. If any item is missing or damaged, please contact your local dealer for service.
2.3 Optional Accessory
The POE-GSH1816R-250 has the following optional accessories which you can purchase
from AirLive
1000Base-SX MiniGBIC Transceiver (Model: SFP-SX v2) or 1000Base-LX
MiniGBIC Transceiver (Model: SFP-LX v2) is for your SFP slots of
POE-GSH1816R-250, it allows you to use fiber cable for extending transmission
distance.
Note: While installing MiniGBIC into SFP slot of POE-GSH1816R-250, please
notice the direction of MiniGBIC is correct, and make sure that MiniGBIC is indeed
installed in the POE-GSH1816R-250.

2. Installing the POE-GSH1816R-250
5 AirLive POE-GSH1816R-250 User Manual
2.4 Knowing your POE-GSH1816R-250
Below are descriptions and diagrams of the product:
2.5 Hardware Installation
Set the POE-GSH1816R-250 on a sufficiently large flat space with a power outlet nearby.
The surface where you put your POE-GSH1816R-250 should be clean, smooth, level and
sturdy. Make sure there is enough clearance around the POE-GSH1816R-250 to allow
attachment of cables, power cord and allow air circulation.
2.5.1.Attaching Rubber Feet
A. Make sure mounting surface on the bottom of the POE-GSH1816R-250 is grease and
dust free.
B. Remove adhesive backing from your Rubber Feet.
C. Apply the Rubber Feet to each corner on the bottom of the POE-GSH1816R-250.
These footpads can prevent the Switch from shock/vibration.

2. Installing the POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
6
2.5.2.Rack-mounted Installation
The POE-GSH1816R-250 comes with a rack-mounted kid and can be mounted in an EIA
standard size, 19-inch Rack. The POE-GSH1816R-250 can be placed in a wiring closet
with other equipment. Perform the following steps to rack mount the POE-GSH1816R-250:
A. Position one bracket to align with the holes on one side of the POE-GSH1816R-250
and secure it with the smaller bracket screws. Then attach the remaining bracket to the
other side of the POE-GSH1816R-250.
B. After attached mounting brackets, position the POE-GSH1816R-250 in the rack by
lining up the holes in the brackets with the appropriate holes on the rack. Secure the
POE-GSH1816R-250 to the rack with a screwdriver and the rack-mounting screws.

2. Installing the POE-GSH1816R-250
7 AirLive POE-GSH1816R-250 User Manual
Note: For proper ventilation, allow about at least 4 inches (10 cm) of clearance on the
front and 3.4 inches (8 cm) on the back of the Switch. This is especially important for
enclosed rack installation.
2.5.3.Power On
Connect the power cord to the power socket on the rear panel of the POE-GSH1816R-250.
The other side of power cord connects to the power outlet. The internal power supply of the
POE-GSH1816R-250 works with voltage range of AC in the 100-240VAC, frequency
50~60Hz. Check the power indicator on the front panel to see if power is properly supplied.
2.6 LED Table
The LED Indicators gives real-time information of systematic operation status. The
following table provides descriptions of LED status and their meaning.

2. Installing the POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
8
LED Status Description
System
Green
Power is ON
Link/ACT/Speed
Green On
Link up 1000M
Yellow On
Link up 100M
Blinking
Data activating
PoE
Green
PoE device connecting

3. Introduce the POE-GSH1816R-250
9 AirLive POE-GSH1816R-250 User Manual
3
3.Introduce the
POE-GSH1816R-250
3.1 Important Information
The following information will help you to get start quickly. However, we recommend you to
read through the entire manual before you start. Please note the username and password
are case sensitive.
The default IP address is 192.168.2.1
The default Subnet Mask is 255.255.255.0
The default username is admin
The default password is airlive
3.2 Prepare your PC
The POE-GSH1816R-250 can be managed remotely by a PC through RJ-45 cable. The
default IP address of the POE-GSH1816R-250 is 192.168.2.1 with a subnet mask of
255.255.255.0. This means the IP address of the PC should be in the range of 192.168.2.2
to 192.168.2.253.
To prepare your PC for management with the POE-GSH1816R-250, please do the
following:
1. Connect your PC directly to the copper port of POE-GSH1816R-250
2. Set your PC’s IP address manually to 192.168.2.100 (or other address in the same
subnet)
3.3 Management Interface
The POE-GSH1816R-250 can be configured using on the management interfaces below:

3. Introduce the POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
10
Web Management (HTTP): You can manage your POE-GSH1816R-250 by simply
typing its IP address in the web browser. Most functions of POE-GSH1816R-250 can
be accessed by web management inter face. We recommend using this interface for
initial configurations. To begin, simply enter POE-GSH1816R-250’s IP address
(default is 192.168.2.1) on the web browser. The default username is admin and
password is airlive.
3.4 Introduction to Web Management
The POE-GSH1816R-250 offers Web Management interfaces for users. Users can easily
access and control POE-GSH1816R-250 via web browsers. The Web-Based Management
supports Internet Explorer 10 or later version. If you want to check the cameras’ stream,
please use Firefox , because other browser does not support the plug-in for video.
3.4.1.Getting into Web Management
Web Management (HTTP)
1. Launch the Internet Explorer.
2. Type http://192.168.2.1. Press “Enter”.
3. The login screen appears.
4. Key in the user name and password. The default user name is “admin” and password
is “airlive”.

3. Introduce the POE-GSH1816R-250
11 AirLive POE-GSH1816R-250 User Manual
5. Click “Enter” or ”Login”, then the home screen of the Web-based management
appears.
3.4.2.Menu Structure of POE-GSH1816R-250
The web management menu of POE-GSH1816R-250 is divided into 3 parts: Top Bar, Side
Menu Bar, and Main Screen.
Side Menu
Main Screen
Top Bar

3. Introduce the POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
12
Top Bar: It display panel GUI. You can direct click the port on the Switch figure
on the top of web page. Then, you will see the port information. On the left-top
corner, there is a pull-down list for Auto Logout. For the sake of security, we provide
auto-logout function to protect you from illegal user as you are leaving. If you do not
choose any selection in Auto Logout list, it means you turn on the Auto Logout
function and the system will be logged out automatically when no action on the
device 3 minutes later. If OFF is chosen, the screen will keep as it is. Default is ON.
Side Menu: All management functions will show in Side Menu, you can choose any
one of them to configure its setting. The detailed introduction for all management
function will explain in below chapters. The following list is the full function tree for
web user interface.
Main Screen: Once choosing any function of Side Menu, the configuration page of
the function will show in Main Screen. You can configure the function by instruction
of manual.

4.Web Management: System of POE-GSH1816R-370
13 AirLive POE-GSH1816R-250 User Manual
4
4.Web Management:
System of
POE-GSH1816R-250
4.1 System
This chapter describes the entire basic configuration tasks which includes the System
Information and any manage of the Switch (e.g. Time, Account, IP, Syslog and NTP.)
4.1.1.System Information
You can identify the system by configuring the contact information, name, and location of
the switch.
4.1.1.1. Information
The switch system information is provided here.
Web interface
To configure System Information in the web interface:
1. Click Monitor, System and Information.
2. Check the contact information for the system administrator as well as the name and
location of the switch. Also indicate the local time zone by configuring the appropriate
offset.
3. Click the “Refresh”

4.Web Management: System of POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
14
Parameter description:
1. Model Name
Model Name will show POE-GSH1816R-250 by different models
2. System Description
Displays the system description.
3. Hardware-Mechanical Version
The hardware and mechanical version of this switch.
4. Firmware Version
The software version of this switch.
5. MAC Address
The MAC Address of this switch.
6. Series Number
The serial number of this switch.
7. Platform Name
Displays the user-defined system name that configured in System | System
Information | Configuration | System Name.

4.Web Management: System of POE-GSH1816R-370
15 AirLive POE-GSH1816R-250 User Manual
8. Location
The system location configured in Configuration | System | Information | System
Location.
9. Contact
The system contact configured in Configuration | System | Information | System
Contact.
10. System Date
The current (GMT) system time and date. The system time is obtained through the
Timing server running on the switch, if any.
11. System Uptime
The period of time the device has been operational.
4.1.2.Advance IP Setting
This sector is to provide and config the IP information of the POE-GSH1816R-250.
4.1.2.1. IP Configuration
The IPv4 address for the switch could be obtained via DHCP Server for VLAN 1. To
manually configure an address, you need to change the switch's default settings to values
that are compatible with your network. You may also need to establish a default gateway
between the switch and management stations that exist on another network segment.
Configure the switch-managed IP information on this page
Configure IP basic settings, control IP interfaces and IP routes.
The maximum number of interfaces supported is 8 and the maximum number of
routes is 32.
Web Interface
To configure an IP address in the web interface:
1. Click Configuration, System, IP.
2. Click Add Interface then you can create new Interface on the switch.
3. Click Add Route then you can create new Route on the switch
4. Click Apply

4.Web Management: System of POE-GSH1816R-250
AirLive POE-GSH1816R-250 User Manual
16
Parameter description:
IP Configuration
1. DNS Server
This setting controls the DNS name resolution done by the switch. The following
modes are supported:
•From any DHCP interfaces
The first DNS server offered from a DHCP lease to a DHCP-enabled interface
will be used.
•No DNS server
No DNS server will be used.
•Configured
Explicitly provide the IP address of the DNS Server in dotted decimal
notation.
•From this DHCP interface
Specify from which DHCP-enabled interface a provided DNS server should
be preferred.