Airone MOZART Installation and operation manual

MOZART
INSTRUCTIONS FOR USING, MAINTAINING AND INSTALLING THE HOOD
EN

INSTRUCTIONS FOR USE, MAINTENANCE AND INSTALLATION FOR THE DOWNDFRAFT.
ATTENTION: The downdraft must only be installed from a qualified technician. Every responsibility
regarding installations from unauthorized persons will be declined.
Before proceeding with the downdraft installation, please read carefully these instructions.
Keep this booklet together with the downdraft.
WARNING
ATTENTION: When the downdraft is closed, do not put pots or other containers on it, in order to
avoid eventual spills in phase of opening.
The downdraft is equipped of a security system of micro-switches that blocks the movement of the
downdraft in case the cover would raise. In phase of closure of the downdraft, if some object is
between the cover and the work top, the raising of the cover will block the movement.
In order to reactivate the movement it will be sufficient to replace the cover and activate the desired
command.
Do not let children or disabled people use the downdraft if not in presence of adults.
Before cleaning or performing any periodic maintenance of the downdraft always ensure the electric
power is turned off by removing the plug from the socket and turning the main switch to position 0
(OFF).
Do not connect the downdraft to any piping used for combustion appliances, such as burners, boilers
or fireplaces.
Check that the main power supply corresponds to the voltage required by the downdraft (see silver
label on the electric box).
Ensure that the electric system is correctly earthed and that the earth discharge works correctly.
When cooking do not use materials that could form high or unusual flames. Oil and fat used twice
are particularly dangerous and could easily catch on fire.
Do not prepare flambé dishes under the hood.
Respect local legislation and regulations issued by the relative authorities regarding the exhaust air
when the suction is operating.
Failure to respect and perform all the maintenance operations described in this booklet could cause
a fire hazard.
INSTALLATION
The suction of the downdrafts, regarding the traditional hoods, is penalized in the suction of the
cooking vapors of the front pots. For this reason the use of a panoramic glass ceramic top is
suggested.
The downdraft can be used for both filtering and suction.

When the filtering function is operating, with air recycle, carbon filters must be used.
When the downdraft is used in the filtering function, there must be a suitable section for spillage of
the air suction on the base of the kitchen.
When the suction function is operating, exhausting the filtered air on the outside, a suitable
compensation system must be used according to current standards in force. The diameter of the
fume exhaust pipe must be the same or greater than the diameter of the downdraft pipe union.
There must be sufficient ventilation in the room where the downdraft is installed, to allow the
simultaneous use of other appliances that use gas or other fuels.
ASSEMBLY INSTRUCTIONS
Make a hole in the downdraft approximately 50mm from the work top hole.
For the dimensions of the hole, see drawing here below.
The gluing of the optional cover (as rule, use the same material of the work top) of the downdraft,
must be performed in the same place after finishing the assembly of the downdraft.
The controls must be assembled in order to guarantee an eventual attendance of technical
assistance.
In the kitchen furniture, provide in front of the downdraft a removable wall.

It is possible to connect on the front or on the back part of the downdraft a tube of diameter 150. It is
possible to connect on the side of the downdraft a tube 220x90 or 230x80 on both sides.
As for the height adjustment of the moving part of the downdraft, see Fig. 2.
According to the thickness of the cover, it is possible to adjust of 20mm.
This adjustment is possible by acting on the two screws that secure the central pivot of the actuator
Fig.3
Fig. 1
Fig. 2
OPTIONAL COVER
HOOD
Fig. 3

ELECTRIC WIRING
Safety Instructions:
Before any manipulation of the controller power cord (230 volt)
Before each operation, all devices connected
Electrical connections must be performed by professionals
1 - External motor connector
2 - Power supply 230V
3 - Cable with faston for microswich
hood
4 - Remote control antenna cable
(has to remain free)
5 - Hood activator cable
6 - Power led
1
5
3
4
2
6

MOZART CONTROL FUNCTIONS
PLEASE NOTE : THE SUCTION OF THE DOWNDRAFT CAN BE STARTED ONLY WHEN THE
DOWNDRFT IS COMPLETLY EXTRACTED.
BUTTON “A”
With suction motor turned on, every time the button is pressed
the motor speed will be reduced of one step.
BUTTON “B”
With the downdraft completely removed, the suction motor can
be turned on and/or off.
While pressing the button long enough, the suction motor turns
off automatically.
The activation of the timer is signaled by the blue flashing led
and the suction motor turns off after 10 minutes.
BUTTON “C”
With suction motor turned on, every time the button is pressed
the motor speed will be increased of one step.
BUTTON "D"
By pressing the button once, the downdraft is completely
extracted.
If the button is pressed while the downdraft is moving, the
downdraft automatically stops.
To restart the movement, it is necessary to press button "D" or
"E".
BUTTON “E”
By pressing the button once, the downdraft returns in
completely.
If the button is pressed while the downdraft is moving, the
downdraft automatically stops.
To restart the movement, it is necessary to press button "D" or
"E".
If the button is pressed when the suction motor is on, the motor
automatically turns off.
NOTES:
- At first use it is necessary to start the
remote control learning.
When the downdraft is turned off, keep
button "F" pressed for a long time.
The remote control learning is indicated
with the flashing led.
If, within one minute there is a valid remote
control code (sent by pressing any button
of the remote control), the led will be on
continuously for 3 seconds and then it will turn off, indicating the proper learning.
USE AND MAINTENANCE
Before beginning any sort of cleaning and maintenance work, turn off the power of the downdraft by
turning the main switch to 0 (OFF).
Cleaning the metal filters
The metal filters fitted in the downdraft should be washed every 2-3 months depending on how much
they are used, using hot water and a non aggressive liquid detergent.
To access the metal filters, you must open the cover from the downdraft. In order to open the cover,
F

take the cover out from the downdraft and open the cover lifting it upwards. (Fig.A)
The metal filters can be removed using the special handle unhooking first the filter in the front part
and pulling up. (Fig.B)
After washing the filters, they must be thoroughly dried and reassembled correctly.
Carbon filters
If the downdraft is used with the internal recycle filtering system, then
active carbon filters must be used.
The active carbon in the filters traps the cooking smells.
Warning: The carbon filters can not be reused or washed and should
be changed periodically (every 4 months if the hood is used for two
hours every day). Saturated filters cause fire hazards.
The carbon filters are placed underneath the metal filters.
Cleaning the hood
If the downdraft is stainless steel, use specific products and rags for satin stainless steel (non-
abrasive and / or corrosive detergents free of chlorine), ensuring to clean in the same direction as
the satin finish.
Do not use aggressive products, chemical solvents or derivatives of oil distillates that could leave oily
traces which could cause oxidation and polymerization.
The manufacturer is not responsible for damage to the surface of the downdraft due to failure
to respect these instructions.
Fig. A
Fig. B

Airone S.r.l. - Via Ghebo, 12 - 35017 Piombino Dese (PD) Italy
tel [phone] fax [phone]
www.aironehoods.com
WK07 Y2012 REL.00 COD.DOLIMOZART00000022