Airpura G600 Use and care manual

To close the lter chamber
Replace
the gasket
Position the
indentation in the cover
into the center of the
HEPA lter
Replace
the 4 screws
and tighten
Turn the Airpura
back on casters
To open the lter chamber
OPER ATING
&
FILTER REPLACEMENT
DIRECTIONS
G600
Position
the Prelter
inside the lter
chamber
Place a felt gasket at
the bottom of the
lter chamber
Place the HI-C lter
around the Hepa lter and
Attach the HI-C lter with
the elastic bands
Roll it
into a spiral
Unfold the lter slider
(Supplied with replacement
lters or on request
Part#6F 001)
Insert the tube into
the lter chamber
inside the Prelter
Let the spiral open to
ll the opening
Open the top of the
spiral to make a
slight funnel
Insert the
Carbon canister
into the funnel and
hold it straight
Let the canister
slide down
thelter slider
Pull the lter slider
up out of the cavity
using both hands
and let the canister
slide to the bottom
of the cavity
Remove the lter
slider and fold it for
further use
Slide in the
Hepa lter
Turn over
the Airpura
Remove the 4
retaining screws
Take off
the cover
Remove
the gasket

Air puriers models and lter congurations
Technical specications
3067330 60950
Odor, airborne
chemical control
18 lbs German carbon Filter
carbon 13"H x 13.25"OD x 9"ID
Carbon bed
570 in2x 2 in deep
Particle removal
40 sq ft true HEPA
(Measured 1 side only)
12 pleats per inch
Pleats warm rolled with separators
Air ow 560 cfm
More cfm than any
other home unit available
Pre-lter
570 in2x 1 in deep
Size
23 in x 15 in
Weight
45 lbs total
Voltage options
110 or 220 volts
Watts
120 on high / 40 on low
Sound level
28.1 db on low (at 6 feet)
62.3 db on high (560 cfm)
(Room level 25.1 db)
ETL certied
Conforms to CSA C22.2
no 113 ANSI / UL 507
18 lbs German Carbon Filter
12-24 months
HEPA 600RVHU Filter
(99.97 % ecient @ 0.3 Microns)
3 to 5 years
Poly Prelter C600 2PK
12 months
Prelter Particule Carbon
Alternates Cotton Prelter
TarBarrier Prelter
TO BEGIN USING YOUR
AIRPURA
Inspect the exterior of your Airpura to verify there is no damage from shipping.
If any damage is noted, please follow the instructions from the distributor returns
policy.
Wipe the unit with a damp cloth to remove any dust from packaging
Plug the unit into a regular grounded 110 volt outlet
Turn on the unit to MAX and allow it to run for a few minutes
Set the variable speed control to the level you wish
The most ecient way to use your Airpura for regular air quality maintenance
is to run it at a low speed 24 hours a day 7 days a week.
FILTER MAINTENANCE AND REPLACEMENT
The Prelter
Can be vacuumed from the exterior of the unit once a month or more often.
Should be replaced at least after 12 months of use
To vacuum the Prelter
Use the brush attachment on your vacuum cleaner
Vacuum slowly around the mesh surface of the lter chamber
IMPORTANT SAFETY NOTE
Please ensure air purier is turned OFF when plugging into a power source.
Failure to do so may result in motor potentially stalling and/or burning.
MinMax
Off
1
MinMax
Off
2
MinMax
Off
3