Airpura P600 Use and care manual

OPER ATING
&
FILTER REPLACEMENT
DIRECTIONS
P600

TO BEGIN USING YOUR
AIRPURA
Inspect the exterior of your Airpura to verify there is no damage from shipping.
If any damage is noted, please follow the instructions from the distributor returns
policy.
Wipe the unit with a damp cloth to remove any dust from packaging
Plug the unit into a regular grounded 110 volt outlet
Turn on the unit to MAX and allow it to run for a few minutes
Set the variable speed control to the level you wish
The most ecient way to use your Airpura for regular air quality maintenance
is to run it at a low speed 24 hours a day 7 days a week.
Always maintain a humidity level of 35% or less in your home to ensure the
unit is operating at optimal levels. Overly humid conditions can have an
adverse effect on the performance of the carbon. When using purier with a
dehumidier, please keep dehumidier at least 6 feet away.
MinMax
Off
1
MinMax
Off
2
MinMax
Off
3
Replacing the UV bulb
Open the lter chamber following
the instructions
Pull the bulb upward out of the
connector
Push the replacement bulb rmly
into the connector
Close the lter chamber following
instructions
The Prelter
Can be vacuumed from the exterior of
the unit once a month or more often.
Should be replaced at least after 12
months of use
To vacuum the Prelter
Use the brush attachment on your
vacuum cleaner
Vacuum slowly around the mesh
surface of the lter chamber
IMPORTANT SAFETY NOTE
Please ensure air purier is turned OFF when plugging into a power source.
Failure to do so may result in motor potentially stalling and/or burning.
FILTER MAINTENANCE AND REPLACEMENT
Ensure regular maintenance/replacement of lters

Air puriers models and lter congurations
Technical specications
3067330 60950
HEPA 600RVHU Filter
(99.97 % ecient @ 0.3 Microns)
3 to 5 years
P614 : HEPA 14 Filter
(99.99% ecient @ 0.3 Microns)
P600+ : HEPA 600 Filter w/ TiO2
(99.97% ecient @ 0.3 Microns)
P614+ : HEPA 14 Filter
(99.99% ecient @ 0.3 Microns) +
TiO2
18 lbs, Coconut Shell Carbon
Filter (100% Blend)
24 months
Titanclean
18-20 months
UV bulb
18-20 months
Poly Prelter 600 2-pack
12 months
Particle removal
Over 100 ft2true HEPA
(Measured only 1 side)
12 pleats per inch
Pleats warm rolled with separators
Activated carbon lter
18 lbs carbon lter
13"H X 13.25"OD X 9"ID
Carbon Bed
2” deep X 570 sq. surface
Air Flow 560 cfm
More cfm than any other
home unit available
Prelter
570 in2x 1 in
Housing
Powder coat steel
Size
23 in x 15 in
Weight
35 lbs total
Watts
120 on high / 40 on low
Sound Level
28.1 db on low (at 6 feet)
62.3 db on high (560 cfm)
(Room level 25.1 db)
Voltage options
115 or 220 volts
ETL Certied
Conforms to CSA C22.2
no 113 ANSI / UL 507
Prelter Particule Carbon
Alternates Cotton Prelter
TarBarrier Prelter 18 lbs anthracite carbon lter (100%)
Upgrade HEPA 14 Filter
(99.99 % ecient @
0.3 Microns)
ULPA Filter (99.9999 %
ecient @ 0.1 Mi-
crons)
18 lbs impregnated carbon
18 lbs carbon (17% potassium
permaganate carbon, 83% coco-
nut shell

To close the lter chamber
Replace
the gasket
Position the
indentation in the cover
into the center of the
HEPA lter
Replace
the 4 screws
and tighten
Turn the Airpura
back on casters
Insert the tube
into the lter
chamber inside
the Prelter
Let the spiral
open to ll
the opening
Open the top of the
spiral to make a
slight funnel
Insert the
Carbon canister into
the funnel and hold it
straight
Position the
Prelter inside
the lter
chamber
Place a felt gasket at
the bottom of the
lter chamber
Unfold the lter slider
(Supplied with replacement
lters or on request
Part#6F 001)
Roll it
into a spiral
Let the canister
slide down
thelter slider
Pull the lter slider up
out of the cavity using
both hands and let the
canister slide to the
bottom of the cavity
Remove the lter
slider and fold it
for further use
Slide in the
Hepa lter
To open the lter chamber
Turn over
the Airpura
Remove the 4
retaining screws
Take off
the cover
Remove
the gasket