Airrobo P10 User manual

User ManualScan this QR code forstep-by-step videos

ContentsEnglishP01-P10.................................................................................................................................................ENDeutschP11-P20 ...............................................................................................................................................DE日本語P21-P30.................................................................................................................................................JPРусскийP31-P40 ...............................................................................................................................................RUFrançaisEdition électronique ..........................................................................................................................FREspañol E-edición...............................................................................................................................................ESItalianoEdizione elettronica.............................................................................................................................ITTips:Scan the QR code on the left to get the latest manual.English/Deutsch/日本語/Русский/Français/Español/Italiano included.AIRROBO airrobo_oﬃcial

Part 1 Important information1.1 Before ﬁrst use• Before using this robot vacuum cleaner, please read these instructions completely. And please save this manual and pass it on to next user. Unbox it and remove all protective packaging and wrappings.• Ensure to check all parts are included. If the unit is incomplete, kindly return it to the retailer immediately. And take the entire unit with its original packaging and the proof of purchase to the store where your purchase was made.• Before using the robot vacuum cleaner, please make sure that the power outlet is switched on and you remove all obstacles from the immediate environment. It will pass over each section of the ﬂoor several times to build up the map through cleaning. • The side brushes may occasionally resist smaller particles (dog food, cat litter), but the robot vacuum cleaner will remove them all eventually. Please empty the dustbin after each use to guarantee the maximum performance afterwards.• The robot vacuum cleaner may not be able to clean up dirt and dust if its dustbin is full. It is recommended that you clean the dustbin regularly.• Please make sure that you discard or safely store the packaging and wrappings after the checkups above. For the safety, please keep your babies, infants, and children away from this stuﬀ.1.2 WARNING• Only authorized technicians may be able to dismantle the robot vacuum cleaner. Users must not dismantle or repair it.• Use the original adapter supplied by the manufacturer only. The incompatible adapters may cause electric shocks, ﬁre, or the damage of the robot vacuum cleaner.• Do not touch the plug or the adapter when your hands are wet.• Keep clothes and sticks away in case of getting the wheels stuck.• Keep the robot vacuum cleaner away from cigarettes, lighters, matches or other ﬂammable materials.• Do not use force to bend the power cable and do not let it bear with pressure from heavy or sharp objects.• The robot vacuum cleaner is only for using indoors. Do not use it outdoors.• Do not sit on the robot vacuum cleaner or place any objects on top of it.• Do not use the robot vacuum cleaner in a wet or damp environment.• Clear the ﬂoor before using the robot vacuum cleaner and remove all fragile items, cables, clothes, papers, and curtains, etc., as they might get tangled in it.• Limited to use the robot vacuum cleaner on stable and level surfaces.• Turn oﬀ the power if the robot vacuum cleaner remains unused for a longer period.• Check before each use that the adapter and plug are correctly connected.• Check if the adapter and the plug are correctly connected before each use.• Tell everyone at home or in the oﬃce when the robot vacuum cleaner is in operation so that no one trips over it.• The robot vacuum cleaner is unable to cross over the height diﬀerence of more than 12mm.• Only use the robot vacuum cleaner in the temperature range between 0°C and +60°C (degrees Celsius) and do not expose it to higher temperatures.• Remove the battery before scrapping the robot vacuum cleaner.• Disconnect the robot vacuum cleaner from the power supply before removing the battery. • Dispose of the battery properly.Notes: Ensure that children and people with mental or physical disabilities use the equipment under supervision.Part 2 Product overview2.1 Packing listMain unit（main brush x 1， dustbin x 1，ﬁlter x 1，and side brush x 2） x 1 Charging base x 1 Power adapter x 12.2 Product Appearance• Main unitThank you for purchasing AIRROBO ROBOT VACUUM CLEANER. • It is strongly recommended to read and understand the user manual comprehensively, including proper use, safety information and maintenance instructions for AIRROBO ROBOT VACUUM CLEANER, before using.• The user manual oﬀers instructions only. If there are any other situations that you encounter that may not be addressed through this user manual, please contact our customer service support.airrobo@ubtrobot.com for product technical support.• This user manual will be updated upon new software or hardware updates, and content and images will be updated without further notice.-1-

Part 1 Important information1.1 Before ﬁrst use• Before using this robot vacuum cleaner, please read these instructions completely. And please save this manual and pass it on to next user. Unbox it and remove all protective packaging and wrappings.• Ensure to check all parts are included. If the unit is incomplete, kindly return it to the retailer immediately. And take the entire unit with its original packaging and the proof of purchase to the store where your purchase was made.• Before using the robot vacuum cleaner, please make sure that the power outlet is switched on and you remove all obstacles from the immediate environment. It will pass over each section of the ﬂoor several times to build up the map through cleaning. • The side brushes may occasionally resist smaller particles (dog food, cat litter), but the robot vacuum cleaner will remove them all eventually. Please empty the dustbin after each use to guarantee the maximum performance afterwards.• The robot vacuum cleaner may not be able to clean up dirt and dust if its dustbin is full. It is recommended that you clean the dustbin regularly.• Please make sure that you discard or safely store the packaging and wrappings after the checkups above. For the safety, please keep your babies, infants, and children away from this stuﬀ.1.2 WARNING• Only authorized technicians may be able to dismantle the robot vacuum cleaner. Users must not dismantle or repair it.• Use the original adapter supplied by the manufacturer only. The incompatible adapters may cause electric shocks, ﬁre, or the damage of the robot vacuum cleaner.• Do not touch the plug or the adapter when your hands are wet.• Keep clothes and sticks away in case of getting the wheels stuck.• Keep the robot vacuum cleaner away from cigarettes, lighters, matches or other ﬂammable materials.• Do not use force to bend the power cable and do not let it bear with pressure from heavy or sharp objects.• The robot vacuum cleaner is only for using indoors. Do not use it outdoors.• Do not sit on the robot vacuum cleaner or place any objects on top of it.• Do not use the robot vacuum cleaner in a wet or damp environment.• Clear the ﬂoor before using the robot vacuum cleaner and remove all fragile items, cables, clothes, papers, and curtains, etc., as they might get tangled in it.• Limited to use the robot vacuum cleaner on stable and level surfaces.• Turn oﬀ the power if the robot vacuum cleaner remains unused for a longer period.• Check before each use that the adapter and plug are correctly connected.• Check if the adapter and the plug are correctly connected before each use.• Tell everyone at home or in the oﬃce when the robot vacuum cleaner is in operation so that no one trips over it.• The robot vacuum cleaner is unable to cross over the height diﬀerence of more than 12mm.• Only use the robot vacuum cleaner in the temperature range between 0°C and +60°C (degrees Celsius) and do not expose it to higher temperatures.• Remove the battery before scrapping the robot vacuum cleaner.• Disconnect the robot vacuum cleaner from the power supply before removing the battery. • Dispose of the battery properly.Notes: Ensure that children and people with mental or physical disabilities use the equipment under supervision.Part 2 Product overview2.1 Packing listCleaning brush x 1 Remote control x 1 User manual x 1 Quick start guides x 12.2 Product Appearance• Main unitCLEAN buttonTop coverCLEAN buttonDustbinPower switchSignal window（Built in recharging sensor/wall sensor/anti-collision sensors）BumperCliﬀ sensorsCharging contact pointOmnidirectional wheelBattery coverMain wheelMain wheelSide brushMain brush• Press this button to start/pause cleaning• Press and hold this button for 3 seconds to make the robot vacuum cleaner return to the charging base• Press and hold this button for 8 seconds to reset the Wi-Fi-2-

ButtonFunctionReset Wi-FiChargingForwardLeftRightStart /StopMove forward Start returning to the base to chargeThe voice prompt volume turns up when the robot vacuum cleaner is resetting, and the button’s indicator it would blink blue.Start or pause cleaningTurn rightTurn left• Charging base• Remote control• DustbinNotes： Use one hand to press the dustbin release buckle and use the other one to open the dustbin while opening the cover.Notes:• Install two AAA batteries in the remote control, making sure that the positive and negative ends follow the markings indicated in the battery compartment. Turn on the switch on the side of the robot vacuum cleaner.• Please aim at the robot vacuum cleaner when pressing the buttons of the remote control. • When the robot vacuum cleaner is not connected to Wi-Fi network, you can operate it with the remote control.• If you press any direction button to start the robot vacuum cleaner, it will back up a bit and turn 180° when it is on the charging base, then you can command normally through the remote control.• Remove the batteries if you will not use the remote control for a longer period.* Two AAA batteries are not included in the package.Power indicatorSignal emission areaAdapter portPrimary ﬁlterCharging contact pointsAdvanced ﬁlterDustbin releasebuckleDustbin coverSuction LevelIncrease the suction power of your robot vacuum cleanerSpot cleaningSpiral cleaningStart a zigzag cleaning of current small areaStart a spiral cleaning of current small areaEdge cleaningFind and clean along the wall automaticallySwitch languagesSwitch to language:English/Deutsch/日本語/Русский-3-IndicatorCharging buttonReset Wi-FibuttonDirection: Left Direction: ForwardDirection: RightSpot cleaningSpiral cleaningSwitch languagesStart / Stop Suction LevelEdge cleaning

3.3 App Download and Wi-Fi ConnectionNotes: The Tuya Smart App only works with robot vacuum cleaners under Wi-Fi. Please turn on the robot vacuum and connect the Wi-Fi when running the App. If the connection fails, it’s probably because you are using 5GHz network. Please check out “Common router setting method” and change it to 2.4GHz.3.4 Start working1) Start/Pause• After turning on the power switch on the side of the robot vacuum cleaner, press the Clean ( ) button on it or tap the Clean button on the app to start cleaning.• While cleaning, if you press the Clean ( ) button again or press the Pause button on the app, the robot vacuum cleaner will stop its current task.2) ChargingMethod 1: When the robot vacuum cleaner is on hold, press and hold the Clean ( ) button for 3 seconds, then it will return to the charging base to charge.Method 2: Press the Recharge ( ) button on the remote control, then the robot vacuum cleaner will go back to the charging base to charge. Method 3: Manually place it on the charging base to charge3) Auto CleaningAfter startup, the robot vacuum cleaner will plan the cleaning route in a zigzag pattern, then cleans along room’s edge. When the cleaning is complete, it will automatically return to the charging base to charge.4) Spot cleaningUse the remote control to operate the robot vacuum cleaner or directly place it in the lower-left corner of the area to be cleaned, and tap the Spot button in the App or press the Spot cleaning ( ) button on the remote control, then it will start a zigzag cleaning for the area from the current position and return to the charging base after cleaning.5)Spiral cleaningUse the remote control to operate the robot vacuum cleaner or place it in cleaning-centered area, tap Spiral button in the app or press the Spiral cleaning ( ) button on the remote control, then it will perform the cleaning from the current position and return to the charging base after cleaning.6) Edge cleaningTap the Edge button in the app or press the Edge cleaning ( ) button on the remote control, the robot vacuum cleaner will ﬁnd the wall and clean along the wall automatically. When the cleaning is complete, it will return to the charging base to charge.7) Scheduled cleaningTap the Settings button in the app, set a cleaning time, then the robot vacuum cleaner will start to clean at the speciﬁed time. When the cleaning is complete, it will go back to the charging base to charge.8) Reset Wi-FiWhen you need to connect the robot vacuum cleaner with other mobile phone, or when the mobile phone fails to connect to it, please press and hold the Clean ( ) button on it for 8 seconds or press and hold the Wi-Fi( )button on the remote control for 3 seconds until you hear the voice prompt, then the Clean ( ) button indicator will quickly blink blue, indicating that the Wi-Fi has successfully been reset.9）Suction modeTap the suction button in the app, you can select Quiet, Standard, Powerful, and Max suction modes in the app.1

Tuya Smart

1. Scan the QR code or search “Tuya Smart” on App Store or Google Play to download the App.1.1 Please make sure your phone is connected to 2.4GHz Wi-Fi network and turn on the Bluetooth before downloading Tuya Smart.x

4. Add the robot vacuum cleaner it found.3. Click [Add device] or press [+] to add the robot vacuum cleaner.1.2 Turn on the robot vacuum cleaner, press the [Wi-Fi] button on remote control for 5 seconds, then the indicator light will start blinking quickly.5. Select a 2.4GHz Wi-Fi network and enter Wi-Fi name and password. Please note that a dual band with mixed mode (2.4GHz + 5GHz) or simply 5GHz Wi-Fi network will not be able to connect the robot vacuum cleaner.6. Added successful-ly! Click [Done] to enter next step.7. Now you can operate the robot vacuum cleaner through the Tuya Smart App.2. Log in Tuya Smart App. For new users, please create your account before login.8. If you want to connect to Alexa, please click “Alexa” and follow the prompts!3.1 Select the type of robot vacuum cleaner. It is recommended to select the Robot Vacuum (BLE + Wi-Fi).-5-

3.4 Start working1) Start/Pause• After turning on the power switch on the side of the robot vacuum cleaner, press the Clean ( ) button on it or tap the Clean button on the app to start cleaning.• While cleaning, if you press the Clean ( ) button again or press the Pause button on the app, the robot vacuum cleaner will stop its current task.2) ChargingMethod 1: When the robot vacuum cleaner is on hold, press and hold the Clean ( ) button for 3 seconds, then it will return to the charging base to charge.Method 2: Press the Recharge ( ) button on the remote control, then the robot vacuum cleaner will go back to the charging base to charge. Method 3: Manually place it on the charging base to charge3) Auto CleaningPart 4 Cleaning and Maintenance4.1 Cleaning the side brushesClean the side brushes and replace them if they are damaged.Notes: Before replacing the side brushes, check the “L” & “R” marked on the two side brushes and make sure they match the correspond-ing marking at the bottom of the robot vacuum cleaner.4.2 Cleaning the main brush • Turn oﬀ the robot vacuum cleaner. Press the two tabs on the main brush cover to remove the cover and then remove the main brush on the right. Use the cleaning brush to remove hair and other dirt from the main brush.• Rinse the main brush under running water and do not replace it until it is dried completely.Main brush cover Unlocking button for the dustbinMain brushAfter startup, the robot vacuum cleaner will plan the cleaning route in a zigzag pattern, then cleans along room’s edge. When the cleaning is complete, it will automatically return to the charging base to charge.4) Spot cleaningUse the remote control to operate the robot vacuum cleaner or directly place it in the lower-left corner of the area to be cleaned, and tap the Spot button in the App or press the Spot cleaning ( ) button on the remote control, then it will start a zigzag cleaning for the area from the current position and return to the charging base after cleaning.5)Spiral cleaningUse the remote control to operate the robot vacuum cleaner or place it in cleaning-centered area, tap Spiral button in the app or press the Spiral cleaning ( ) button on the remote control, then it will perform the cleaning from the current position and return to the charging base after cleaning.6) Edge cleaningTap the Edge button in the app or press the Edge cleaning ( ) button on the remote control, the robot vacuum cleaner will ﬁnd the wall and clean along the wall automatically. When the cleaning is complete, it will return to the charging base to charge.7) Scheduled cleaningTap the Settings button in the app, set a cleaning time, then the robot vacuum cleaner will start to clean at the speciﬁed time. When the cleaning is complete, it will go back to the charging base to charge.8) Reset Wi-FiWhen you need to connect the robot vacuum cleaner with other mobile phone, or when the mobile phone fails to connect to it, please press and hold the Clean ( ) button on it for 8 seconds or press and hold the Wi-Fi( )button on the remote control for 3 seconds until you hear the voice prompt, then the Clean ( ) button indicator will quickly blink blue, indicating that the Wi-Fi has successfully been reset.9）Suction modeTap the suction button in the app, you can select Quiet, Standard, Powerful, and Max suction modes in the app.4.3 Cleaning the dustbin and ﬁlterHold the dustbin in a horizontal position and press the unlocking button to open the dustbin cover ‒ emptying the dustbin, removing the ﬁlter, and rinsing the dustbin, ﬁlter, and sponge ‒ and then once again assemble the dustbin, ﬁlter, and sponge into the robot vacuum cleaner before drying it out.Notes:• Switch oﬀ the robot vacuum cleaner and disconnect the charging base’s plug before cleaning and maintaining it.• Check there are no foreign matters that were vacuumed before cleaning.• The ﬁlter lasts for 6 months; Please clean the ﬁlter once or twice a month. • Make sure the dustbin, the ﬁlter and the sponge are completely dry before replacing them.• Do not expose the ﬁlter to direct sunlight for a long period.-6-

Part 5 FAQ & Troubleshooting5.1 FAQPart 4 Cleaning and Maintenance4.1 Cleaning the side brushesClean the side brushes and replace them if they are damaged.Notes: Before replacing the side brushes, check the “L” & “R” marked on the two side brushes and make sure they match the correspond-ing marking at the bottom of the robot vacuum cleaner.4.2 Cleaning the main brush • Turn oﬀ the robot vacuum cleaner. Press the two tabs on the main brush cover to remove the cover and then remove the main brush on the right. Use the cleaning brush to remove hair and other dirt from the main brush.• Rinse the main brush under running water and do not replace it until it is dried completely.Fails to power onProblem TypeCause and solution1)When the battery runs low, place the robot vacuum cleaner on the charging base making sure that it’s aligned with the contact points. It will charge automatically (if the battery is completely out of power, it needs to be charged for a while before it is on). 2)The ambient temperature is too low (below 0 °C) or too high (above 45 °C). Please use the robot vacuum cleaner in an environment with a temperature ranging from 0-45 °C)Fails to charge1)Remove the robot vacuum cleaner and check whether the charging base indicator is on. Make sure both the charging base and the power adapter are properly plugged.2)Clean the charging contact points of the robot vacuum cleaner and the base.Fails to go back to the charging base

1)There are too many obstacles near the charging base. Place the charging base along the wall and make sure the area around is open.2)The robot vacuum cleaner is too far away from the charging base to receive the signal. Try placing it near the charging base.

Abnormal noises while cleaningThe side brushes or wheels may be tangled by foreign matters. Please turn oﬀ the robot vacuum cleaner and clean it.Cleaning ability reduced, and dust left behind1) The dustbin is full. Please clean it.2) The ﬁlter is clogged. Please clean it or replace it.3) The side brush is entangled with foreign matters. Please clean the side brush.Fails to connect to the Wi-Fi network1)The Wi-Fi signal is poor. Try to use the robot vacuum cleaner in other places where the Wi-Fi signal is good. 2)The Wi-Fi connection error. Reset the Wi-Fi and download the latest version of the mobile app and try to connect again.3) The password you entered might be incorrect.4) The router used the 5 GHz band, while the robot vacuum cleaner supports the 2.4 GHz only.Fails to perform scheduled cleaningThe battery power is insuﬃcient. The scheduled cleaning function works only when battery power is > 20%. Please make sure the battery power is suﬃcient when using the scheduled cleaning function.Does the robot consume power when it is on the charging dock?The power doesn’t consumer a lot when the robot vacuum cleaner is on the charging base. Placing it on the base helps the battery maintain its condition to the best.Charging contact pointsContact points for charging4.3 Cleaning the dustbin and ﬁlterHold the dustbin in a horizontal position and press the unlocking button to open the dustbin cover ‒ emptying the dustbin, removing the ﬁlter, and rinsing the dustbin, ﬁlter, and sponge ‒ and then once again assemble the dustbin, ﬁlter, and sponge into the robot vacuum cleaner before drying it out.Notes:• Switch oﬀ the robot vacuum cleaner and disconnect the charging base’s plug before cleaning and maintaining it.• Check there are no foreign matters that were vacuumed before cleaning.• The ﬁlter lasts for 6 months; Please clean the ﬁlter once or twice a month. • Make sure the dustbin, the ﬁlter and the sponge are completely dry before replacing them.• Do not expose the ﬁlter to direct sunlight for a long period.-7-

Part 6 SpeciﬁcationsMain unitsDimensions315*315*79mmBattery capacity2600mAhBattery Lithium batteryDustbin capacity510ml Charging methodsAuto-charging/manual chargingCleaning modeAuto/Spot/Spiral/EdgeOperaing humidity rangeCharging duration≤300min≤90%RHNoise≤ 65dBOperaing temerature range0~45℃AccessoriesPower adapterOutput voltageOutput current0.6ACharging baseInput voltage19V14.4VFault voice promptError 1: I need to change my starting location.The robot vacuum cleaner is lifted or suspended.Error 2: Wipe oﬀ the bottom anti-drop sensors.The cliﬀ sensor (s) is covered, dirty, or suspended.Error 3: Please clean the IR self-charging sensor.The wall sensor responding to the signal window is dirty or blocked.Error 4: Please wipe oﬀ the wall sensor.The edge of the bumper or internal light touch sensor is stuck.Error 5: Oh, the edge seems to be stuck.Error 6: I’m trapped, please help!The edge of the bumper or internal light touch sensor is stuck.The robot vacuum cleaner is stuck.Error 7: I’m tilted, please set me upright.The robot vacuum cleaner is tilted, please manually set it upright.Error 8: Hey, the main wheel is stuck, please help!The main wheel is stuck or entangled.Error 9: Hey, the side brush is stuck, please help!The side brush is stuck or tangled.Error 10: Where is the charging dock?The robot vacuum cleaner cannot ﬁnd the charging base, or the charging base does not have power.Error 11: Malfunction! Please try restarting me!The robot vacuum cleaner may have encountered an unknown error. Restart it.Error 12: Malfunction! Please power oﬀ.This failure needs to power oﬀ the robot vacuum cleaner. After reminding the user,it automatically shuts down or goes back to the charging base.Error 13: I need to charge!This happens when the battery is lower than 20%, please return the robot vacuum cleaner to charge.Error 14: I cannot shut down the charging dock.The robot vacuum cleaner cannot be powered oﬀ when it is charging on the charging base.Problem and solution5.2 TroubleshootingNotes:• When the robot vacuum cleaner runs abnormally, the indicator ﬂashes red, and its voice prompt turns up. Please refer to the above tables to solve the problem.• If the problem isn’t solved after troubleshooting, please contact the AIRROBO after-sales service (e-mail: support.airrobo@ubtro-bot.com). Do not disassemble the robot vacuum cleaner yourself.-8-

Part 3 Installation and operation3.1 Connect the charging baseAssemble the charging base and switch on the adaptor. Place the charging base close to a wall and remove obstacles approx. 1 M on both sides and approx. 2 M in front of the robot vacuum cleaner. The signal light on the charging base should be on. 3.2 Charging the robot vacuum cleaner for the ﬁrst timeA. Direct chargingPlug the adapter directly into the DC jack on the side of the robot vacuum cleaner, connect the other end of the adapter to the power supply.B. Charged by charging basePlace the robot vacuum cleaner on the charging base to charge, making sure that the contact points are aligned with the charging base.To better maintain the battery life:• Charge the robot vacuum cleaner for 4-6 hours before use. When fully charged, the indicator will stop blinking.• During the normal use, the robot vacuum cleaner will automatically come back to its charging base, connected to the power supply, to charge. • If the robot vacuum cleaner will not be used for a long time, please turn oﬀ the power after it is fully charged and place it in a dry and cool environment. Please charge it every three months to avoid irreversible damage to the battery.Notes: • Before use, remove the protective strip on the bumper to guarantee normal product use.• The power switch is on the side of the robot vacuum cleaner, press “I” to turn it on, and press “O” to turn it oﬀ.• Do not use the robot vacuum cleaner in a suspended environment. If you must use it in a suspended environment, please prevent it from accidentally falling with ﬁrm protective fences, as it may cause personal injury or property loss.• The robot vacuum cleaner will automatically return to the charging base when the battery runs low.Part 7 After-sales ServiceAIRROBO provides a warranty that is processed in the most hassle-free way. This policy should be regarded as a standard service policy that covers products that are sold only by online stores or AIRROBO’s authorized distributors. Kindly contact us at support.airrobo@ub-trobot.com with your order receipt or other proof of purchase for conﬁrmation.Notes: • Consumables delivered with the product are not covered by warranty.• Warranty protections are in addition to rights provided under local consumer laws and may vary among countries.30-day Money-Back Guarantee for Any Reason:Undamaged products may be returned for a full refund for any reason within 30 days of the date the item was delivered to the designated shipping address.• Returns must include all accessories.• Items must include original packaging.• For non-quality related warranty claims, the buyer is responsible for shipping costs.• For non-quality related warranty claims, AIRROBO refunds the cost of the product itself.• Returns may be rejected if the product does not meet the above requirements.It is not possible to process a request for a refund for non-quality issues for items that have expired this 30-day window. For purchases not made directly through online stores, please contact retailers for refunds. For quality-related issues, please see below.Warranty Claims for Quality-Related Issues:All quality-related defects on items sold directly by online stores or authorized distributors are covered by an extensive warranty, starting from the date of purchase.AIRROBO’s limited warranty is restricted to the country of purchase. The limited warranty is invalid on items taken outside the country they were originally bought in or shipped directly from an authorized online purchase.Warranties on all replacements follow the same warranty timeframe of the original defective item, or 3 months after being replaced, whichever is longer.Warranties on products are invalid after having been fully refunded.Process: • Buyer must provide suﬃcient proof of purchase.• AIRROBO must document what happens when buyers troubleshoot the product.• The defective item’s serial number and/or visible proof depicting the defect are required.• It may be necessary to return the item for quality inspection.Valid proof of purchase:• Order numbers from online purchases made through online stores or AIRROBO’s authorized distributors.• Sales invoice.• Dated sales receipt from an authorized AIRROBO reseller that shows a description of the product along with its price.Please note that more than one type of proof of purchase may be required to process a warranty claim (such as receipt of money transfer and conﬁrmation of address item was originally shipped to).Shipping costs must be covered by the buyer in the following situations:• Returning products for any reason other than a proven defect.• Warranty claims on items taken outside the original country of purchase.• Buyer’s accidental returns.• Returning personal items.• Returning items claimed to have defects but found by AIRROBO quality control to be in working condition.• Returning defective items to international shipping.• Costs associated with unauthorized returns (any returns made outside of the approved warranty process).Not Covered Under Warranty:• Products without suﬃcient proof of purchase• Lost or stolen products• Items that have expired their warranty period• Non-quality-related issues (after 30 days of purchase)• Free products• Repairs through 3rd partiesWhen returning items with a prepaid shipping label provided by AIRROBO, AIRROBO takes responsibility for any damage or loss incurred in transit. When returning items for non-quality issues, the buyer assumes responsibility for any damage or loss incurred in transit. AIRROBO does not provide refunds for items damaged in transit for non-quality-related warranty claims.ItemMain unitAccessoriesMain unit (including the built-in lithium battery)1 yearCharging base and power adapter1 yearConsumablesSide brush, ﬁlter, cleaning tools, dustbin, mopping cloth, water tank, ﬁlter cartridge/Warranty ContentWarranty PeriodPart 8 Declaration of Conformity 8.1 FCC Compliance StatementChanges or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.8.2 FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.8.3 EU Declaration of ConformityWe, Best Epoch Technology Co., Ltd. declare under sole responsibility that the above products, to which this declaration relates, is in conformity with the requirements of the following EU Directives:Product description: Robot Vacuum CleanerType designation(s): P10Trademark: AIRROBOHereby we,Name of manufacturer: Best Epoch Technology Co., Ltd Address: 22 Floor, Block Cl, Nanshan I Park, No. 1001 Xueyuan Road, Nanshan District, Shenzhen City, China P.Rdeclare under our sole responsibility that the product described above is in conformity with the relevant Union harmonizationlegislations:European Directive (2014/53/EU)The following harmonized standards and/or other relevant standards have been applied, which included for Article 3.1a Health, Article 3.1b EMC, Article 3.2 Radio Spectrum requirements and Article 3.1a Electrical Safety requirements:EN 55014-1:2017EN 55014-2:2015EN IEC 61000-3-2:2019EN 61000-3-3:2013+Al:2019ETSI EN 301489-1 V2.2.3(2019-ll)ETSI EN 301489-17 V3.2.4(2020-09)EN300 328 V2.2.2(2019-07)EN 62311:2008EN 60335-2-2:2012+All:2012+Al:2013,EN 60335-l:2012+All:2014EN 62233:2008The performed the conformity assessment according to the European Directive, The laboratory issuing the report is Shenzhen Huaxia Testing Technology Co., Ltd.The Technical Documentation (TD) .relevant to the product described above and which support this DoC is available from the EU contact address on this Doc.• Damage from outside sources• Damage from misuse of products (including, but not limited to falls, extreme temperatures, water, and operating robot vacuum cleaner improperly)• Purchases from unauthorized resellers AIRROBO is not liable for• Loss of data incurred from the use of AIRROBO products• Returning personal items sent to AIRROBO-9-

Part 7 After-sales ServiceAIRROBO provides a warranty that is processed in the most hassle-free way. This policy should be regarded as a standard service policy that covers products that are sold only by online stores or AIRROBO’s authorized distributors. Kindly contact us at support.airrobo@ub-trobot.com with your order receipt or other proof of purchase for conﬁrmation.Notes: • Consumables delivered with the product are not covered by warranty.• Warranty protections are in addition to rights provided under local consumer laws and may vary among countries.30-day Money-Back Guarantee for Any Reason:Undamaged products may be returned for a full refund for any reason within 30 days of the date the item was delivered to the designated shipping address.• Returns must include all accessories.• Items must include original packaging.• For non-quality related warranty claims, the buyer is responsible for shipping costs.• For non-quality related warranty claims, AIRROBO refunds the cost of the product itself.• Returns may be rejected if the product does not meet the above requirements.It is not possible to process a request for a refund for non-quality issues for items that have expired this 30-day window. For purchases not made directly through online stores, please contact retailers for refunds. For quality-related issues, please see below.Warranty Claims for Quality-Related Issues:All quality-related defects on items sold directly by online stores or authorized distributors are covered by an extensive warranty, starting from the date of purchase.AIRROBO’s limited warranty is restricted to the country of purchase. The limited warranty is invalid on items taken outside the country they were originally bought in or shipped directly from an authorized online purchase.Warranties on all replacements follow the same warranty timeframe of the original defective item, or 3 months after being replaced, whichever is longer.Warranties on products are invalid after having been fully refunded.Process: • Buyer must provide suﬃcient proof of purchase.• AIRROBO must document what happens when buyers troubleshoot the product.• The defective item’s serial number and/or visible proof depicting the defect are required.• It may be necessary to return the item for quality inspection.Valid proof of purchase:• Order numbers from online purchases made through online stores or AIRROBO’s authorized distributors.• Sales invoice.• Dated sales receipt from an authorized AIRROBO reseller that shows a description of the product along with its price.Please note that more than one type of proof of purchase may be required to process a warranty claim (such as receipt of money transfer and conﬁrmation of address item was originally shipped to).Shipping costs must be covered by the buyer in the following situations:• Returning products for any reason other than a proven defect.• Warranty claims on items taken outside the original country of purchase.• Buyer’s accidental returns.• Returning personal items.• Returning items claimed to have defects but found by AIRROBO quality control to be in working condition.• Returning defective items to international shipping.• Costs associated with unauthorized returns (any returns made outside of the approved warranty process).Not Covered Under Warranty:• Products without suﬃcient proof of purchase• Lost or stolen products• Items that have expired their warranty period• Non-quality-related issues (after 30 days of purchase)• Free products• Repairs through 3rd partiesWhen returning items with a prepaid shipping label provided by AIRROBO, AIRROBO takes responsibility for any damage or loss incurred in transit. When returning items for non-quality issues, the buyer assumes responsibility for any damage or loss incurred in transit. AIRROBO does not provide refunds for items damaged in transit for non-quality-related warranty claims.Part 8 Declaration of Conformity 8.1 FCC Compliance StatementChanges or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.8.2 FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.8.3 EU Declaration of ConformityWe, Best Epoch Technology Co., Ltd. declare under sole responsibility that the above products, to which this declaration relates, is in conformity with the requirements of the following EU Directives:Product description: Robot Vacuum CleanerType designation(s): P10Trademark: AIRROBOHereby we,Name of manufacturer: Best Epoch Technology Co., Ltd Address: 22 Floor, Block Cl, Nanshan I Park, No. 1001 Xueyuan Road, Nanshan District, Shenzhen City, China P.Rdeclare under our sole responsibility that the product described above is in conformity with the relevant Union harmonizationlegislations:European Directive (2014/53/EU)The following harmonized standards and/or other relevant standards have been applied, which included for Article 3.1a Health, Article 3.1b EMC, Article 3.2 Radio Spectrum requirements and Article 3.1a Electrical Safety requirements:EN 55014-1:2017EN 55014-2:2015EN IEC 61000-3-2:2019EN 61000-3-3:2013+Al:2019ETSI EN 301489-1 V2.2.3(2019-ll)ETSI EN 301489-17 V3.2.4(2020-09)EN300 328 V2.2.2(2019-07)EN 62311:2008EN 60335-2-2:2012+All:2012+Al:2013,EN 60335-l:2012+All:2014EN 62233:2008The performed the conformity assessment according to the European Directive, The laboratory issuing the report is Shenzhen Huaxia Testing Technology Co., Ltd.The Technical Documentation (TD) .relevant to the product described above and which support this DoC is available from the EU contact address on this Doc.Signed： Date： Best Epoch Technology Co., Ltd-10-

Best Epoch Technology Co., LTD22 Floor, Block C1, Nanshan I Park, No. 1001 Xueyuan Road, Nanshan District, Shenzhen City, China P.R©Best Epoch Technology Co., LTD. All Rights Reserved. Google Play is a trademark of Google, Inc. Apple, the Apple logo are trademarks of Apple, Inc. Tuyasmart APP is a trademark of Tuya Inc. The pictures of the product are for reference only and subject to change without notice.Tips:Scan the QR code on the left to get the latest manual.English/Deutsch/日本語/Русский/Français/Español/Italiano included.MADE IN CHINAUSAEuropeJapanRussiasupport-jp@ubtrobot.comsupport.airrobo@ubtrobot.com support-ru@ubtrobot.comsupport-eu@ubtrobot.com V3.0

Other manuals for P10

Table of contents