aivituvin AIR01-B User manual

INSTRUCTION
MANUAL
AIR01-B
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
30MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
P5
02
M3.5x35mm SCREW
M3.5x30mm SCREW
M3.5x45mm SCREW
4PCS+1spare
2PCS+1spare
10PCS+1spare
P6
1PC
4PCS+1spare
M3.5x25mm SCREW
4PCS+1spare
M3.0x16mm SCREW
P7 P8
4PCS
1PC

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC
Back panel
Front panel
Left side panel Right side panel
Roof
Divider panel
2PCS
Sliding tray Side panel of feeder Front panel of feeder

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K
04
Wood floor Wire mesh floor
1PC 1PC

PRODUCT ASSEMBLY
01
02
05
Attach a Part E to Part C and Part B by 4pcs of P3 screws.
Attach Part H on two sides of Part I by 4 pcs of P4 screws.
P4X
4
I
E
H
P3X
4
H
C
B

PRODUCT ASSEMBLY
03
04
06
①Attach front panel Part A to two side panels by 4pcs of P2
screws.
②Attach 4pcs of P7 to the hutch leg.
Screw the feeder inside to the front panel A by 2pcs of P1 screws.
P2
X4
P1
X2
A
H
P7
X4
I

PRODUCT ASSEMBLY
05
06
07
Put the wood floor Part J and wire mesh floor Part K above the
tray.
G
P
8
X1
K
J
Slide in the tray Part G.

PRODUCT ASSEMBLY
07
08
08
Put in the divider Part D.
①Attach the roof Part E to the back panel by 6pcs of P5 screws.
②Notice to level up the hinge.
E
D
P5
X6

PRODUCT ASSEMBLY
09
09
Attach the roof highe P6 to the roof panel and right side panel by
4pcs of P5 screws.
P5X4
P6X1
LOCKED
OPEN

HELP CENTER
[email protected]
Question about your product? we're here to help contact us via
Returns & Refunds
?
Product AssemblyOrders FAQProduct inquiry
THANK YOU
Thanks for your support to Aivituvin.
Your satisfaction is our #1 priority.
Once the items are received, opened, and deemed to be faulty
or other problems.
Pls contact us at [email protected] for the solution.
We will feedback to you within 24 hours.
If you are happy with the shopping ,welcome to share photos
and thoughts with others .
www.aivituvin.com
10

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.