aivituvin AIR 22 User manual

INSTRUCTION
MANUAL
AIR 22
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
02
M3.5x60mm SCREW
M4.0x45mm SCREW
8PCS+1spare6PCS+1spare
P3 P4
M3.0x34mm SCREW
M3.5x40mm SCREW
33PCS+1spare24PCS+1spare
P5 P6
M3.5x45mm SCREW
M3.0x16mm SCREW
12PCS+1spare4PCS+1spare
P7
Connect piece
3PCS
P8
Eye hook
4PCS

HARDWARE
P9
03
Hook
2PCS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A2 B1
B2 C1
1PC
1PC 1PC
04
1PC
1PC
Front panel - Upper
Front panel - Down Back panel - Upper
Back panel - Down
Left side panel - Upper
C2
1PC
Left side panel - Down
D1 D2
1PC
1PC
Right side panel - Upper
Right side panel - Down
E
1PC
Roof
A1

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
F G H
I J1
1PC
2PCS 1PC
05
1PC
1PC
Bottom floor
Middle layer Shelf panel in down area
Shelf panel in upper area
Shelf bar in upper area
J2
1PC
Shelf bar in upper area
K L
2PCS
2PCS
Wood handle
Shelf bar in down area
M1
2PCS
Brake casters

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
M2 N1 N2
O P
1PC
2PCS 1PC
06
1PC
1PC
Casters without brake
Left part of small house Right part of small house
Back part of small house
Roof of small house
Q
1PC
Roof connect slats
(This is only for 2 hutches
owner.No usage for only
one hutch owner.)
R
1PC
PVC layer

PRODUCT ASSEMBLY
01
02
07
Screw the handle K to the front panels A1 & A2 by 2xP3 screws each.
①Fix the shelf to the panel, attached 2 pcs Part
4xP1 screws. L to the Part C2 by
②Attached shelf J2 & shelf J1 to the Part C1 by 4xP1 screws.
( Notice do not confuse with the J2, J1.)
P
1
X
K
4
Lx2
C2 C1
A2
A1
P
1
X
4
J1 J2
P
3
X
2
Front panel-upper
P
3
X
2
K
Front panel-down

PRODUCT ASSEMBLY
03
08
①Assemble the down half hutch.
②Attached the 4 sides A2, B2 , C2, D2 together by 8xP3 screws.
P3
X6
B2 D2
04
Screw the 2 casters without brake M2 to the front corners by 3xP3
screws each.
M2x2
C2 A2
P3
X8

PRODUCT ASSEMBLY
05
06
09
Screw the 2 brake casters Part M1 to the back corners by 3xP3
screws each.
①Put the 2 pcs floor Part F into the down half hutch.
②Put the back PVC layers Part R above the wood floor for easier
cleaning.
P3
X6
M1x2
Fx2
R

PRODUCT ASSEMBLY
07
08
10
Attached the shelf panel Part H on the shelf in the down area by
4xP4 screws.
P4
X4
H
Put the middle layer Part G on the top slat of the down hutch close
to the front panel.
G

PRODUCT ASSEMBLY
09
10
11
①Assemble the upper half hutch.
②Attached the 4 sides A1, B1, C1, D1 together by 8xP3 screws.
Connect the front of the up and down hutch by 3xP2 screws.
(Notice there are screw holes to direct finding the right position)
P3
X8
B1
P2
X3
D1
C1 A1

PRODUCT ASSEMBLY
11
12
12
Connect the back of the up and down hutch by 3xP2 screws.
(Notice there are screw holes to direct finding the right position)
①Assemble the small house!
②Attach Part O to N1 & N2 by 4xP4 screws.
③Screw the roof Part P by 4xP4 screws.
P4
X4
P2
X3
O
N1
N2
P4
X4
P

PRODUCT ASSEMBLY
13
13
①Screw the panel I to the small house by 4xP4 screws.
②Attached the panel I to the shelf by 2xP4 screws.
Screw 1xP3 screws through the inner shelf from the bottom.
Notice there is a predrill hole for direction.
I
P4
X2
③
④
P4
X4
P3
X1

PRODUCT ASSEMBLY
14
15
14
①Attached the roof Part E to the hutch by 4xP6 screws.
②Ensure top roof panels line up with each other.
①Insert the eye hook 4xP8 screws into the position as show on the
picture.
②Insert the set of eye hook P9 beside the door.
③Notice there are predrill holes to direct.
P6
X2
E
P8
X2
P6
X2
P8
X2
P9
X1
P9
X1

PRODUCT ASSEMBLY
16
15
①Take out the Part D1 in the left hutch and take out the Part C1
in the right hutch to combine together.
②Then move the small house and shelf which was stay in C1
before to the right side as show on the picture.
D1
C1
REMARK:
The below 3 steps are for 2 hutches to combine together.
If you do only buy one hutch, pls ignore the following.
Small house

PRODUCT ASSEMBLY
17
16
①Screw the connect piece 3xP7 in the middle frame of the 2
hutches by 2xP5 screws each.
②
③Screw the 4 brake casters in the 4 sides corners.
And another 4 casters without brake in the middle positions.
(Brake Casters)
(Brake Casters)
(Casters without brakes)
P7
X3
P5
X6

PRODUCT ASSEMBLY
18
17
Screw the connect piece 3xP7 in the middle frame of the back
hutches by 2xP5 screws each.
Finish
19
Screw the roof connect slats Part Q in the middle by 6xP4 screws.
P7
X3
P5
X6
Q
P4
X6

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.