Aiyima A07 PRO Installation and operation manual

Website:www.aiyima.com Email: [email protected]
[email protected]
Telephone: [phone] VK: https://vk.com/aiyima
Location: 4F, Building 7 Hekan industrial park. Wuhe south road 41. Long-Gang district.
ShenZhen. CHINA. 518000
Shenzhen Yima Technology Co.,Ltd
Bluetooth 5.2
2.0/2.1 Channel Amplifier
USER MANUALS
Model A07 PRO:

2
1
Front Panel Description
Rear Panel Introduction
Specification
2
1
5
3
4
Power switch
Input selector switch；Up: Bluetooth;Down:RCA
Bass adjustment knob
Treble adjustment knob
Volume adjustment knob
2
1
5
3
4
Bluetooth antenna jack（pls install the bluetooth antenna before use）
Right channel input jack
Left channel input jack
Line output jack（Cannot be used for earphones）
Speaker output jacks（For Passive Speaker）
6 Power input jack（Industrial power is not recommended）
Chips TAP3255+QCC304X+NE5532
RCA or Bluetooth
SBC,AAC,APTX,APTX-HD
300W 4Ω 10% THD+N
Bass:±12dB Treble：±9dB
＞92dB
DC24-48V
2-8Ω
0.8V
5.2
Audio Inputs
Bluetooth Audio Codecs
Bluetooth Version
Input Sensitivity
Maximum Output Power
Speaker Impedance
Frequency Response
Input Power Supply Voltage
SNR

FQA
3
Warning
Q: All my wires are connected, but there is no sound?
A: 1 . Check whether the machine is powered on，If there is no response after startup, you can
find a power supply with the same voltage output (must be dc24v-48v) for test.
2. If the startup is normal and there is still no sound, check whether the input and output
lines are correctly connected.
3. If the above two points are normal, check whether the playback device of the input
sound source is suspended, muted or the volume is at the minimum state.
4. Finally confirm the input mode,please switched the correct input modes according to your
connect
4. Check whether the positive and negative poles of the audio input line or audio input line of
the amplifier are inverted.Fix and restart the amp.
5. Check whether the op amp chip inside is loose or detached when it is turned on.There may
be loose components on the circuits, do not attempt to repair,contact us for support.
Q: Does the volume knob control the Aux output as well?
A: No,the Aux output is simply a pass-through for the signal.Volume does not to effect the
3.5mm Aux output.
Q: What's the op amp chip type compatible with aiyima a07 pro?
A: A07 Pro Mini Bluetooth amplifier use 5 pcs NE5532 Dual Op Amp Chips,The 4 of the NE5532
Dual Op chips can be replacement to SRT3609SM ,OPA2604 ,OPA2134 ,LM4562 ,JRC5532 ,
OP275GSZ ,OPA1612AIDR ect Dual Op Amp chips
Q: Why does the amplifier stop working after use a period of time?After a period of time
off, it was working again?
A: Normally, in this case, the amplifier is overheat protected, and the output power may have
exceeded the designed power,so you can lower the volume a little and try again And check
to ensure the output power of the amplifier matches the speakers.
Q: One channel does not work?
A: 1. Check that the positive and negative poles of the speaker do not touch each other.If they
are touch together, separate them and turn on again. Then shut down and restart it
2. Please test whether the Bluetooth and RCA input have the same problem first.If the two
modes have the same problem, swap the speaker cables of the left and right channels,
or change another speaker, and then test whether this channel still does not work;
3. If only RCA or Bluetooth mode does not work, change the audio source,change the RCA
cable and test again, and make sure that all the cables are completely pushed into the device
Q: why is the sound distorted?
A: the input signal amplitude may be too large. If the volume of the machine is adjusted to
the maximum value and the volume of the input source is also adjusted to the maximum
value, it is easy to be distorted. At this point, you only need to lower the volume of the
input source or machine.
Q: why does the volume of the machine remain the same, but the sound size of different
sound sources (such as CD first and then mobile phone) is different?
A: the output signal amplitude is different for different playback devices. For example, mobile
phones are usually 0.35v, while CDs are 1V. The size of natural sound is different.
Q: why does the horn make a loud current sound?
A: If you are not using the original standard power supply, please replace the power supply
and test again. Many power sources in the market have a large disturbance coefficient,
which will cause a large current sound.
Q: why do I not connect the sound source after I plug in the input line, and the speaker
will have a great buzz?
A: when the signal line without shielding is used, there will be interference signals entering
the power amplifier for amplification. It is recommended that you replace the signal line
with shielding or unplug the signal line.
Q: Can this machine be connected to a phonograph / record player?
A: At present, this device does not support phonograph/ record player signal input, because
the output level of phonograph/ record player is very small, need to add a phonograph
amplifier.
Q: why does Bluetooth sound get stuck?
A: when using Bluetooth to test the distance, it is normal that the sound does not get stuck
or disconnected within 10 meters without any obstructions.(Note: the router will interfere
with the Bluetooth signal. Try not to get close!)
1. Please do not open the machine shell. Improper operation may cause electric shock
hazard.
2. Please use the switching power supply of the regular manufacturer, otherwise there will
be the risk of damaging the machine.
3. Please do not operate the machine in high temperature or humid environment.