Akicon 96918P1 User manual

PACKING LIST
IMPORTANT NOTICES: For easy installation, please read all the instruction completely before beginning.
Before installing this product, make sure that water line trash is cleared to avoid blockage.
YOU MAY NEED
After you open this package, please check to ensure that all of the following items are included.
A- Faucet B- Side Spray C- Mounting Nut D-Flexible Hoses(2) E- F- Pull-out hose
H- Mounting Nut
1
EX: E002011T Rev:A
4
TROUBLE-SHOOTING
If you've followed the instruction carefully and your faucet still does not work properly, take these corrective steps.
Problem Cause Action
Leaks underneath handle. Cartridge has come loose. Tighten the cartridge.
Aerator leaks or has an
inconsisitent water flow
pattern.
Aerator is dirty or worn
out or misfitted.
Unscrew the aerator to
clean or replace washer,
or replace the aerator.
Water will not shut off
completely.
Dirty or worn out washer
in cartridge.
Remove handle and cartridge
to check if the washer is damaged
permanently or dirty. Re-install
cartridge.
CAUTION: Maintenance
1. Replacement parts may be available at the store where you purchased your faucet.
2. Always turn off water and relieve pressure before working on your faucet.
NOTES: Cleaning Instructions
1. To keep the faucet clean, you should clean the faucet frequently and regularly.
2. Clean the faucet with clear water or mild liquid, rinse the faucet with clear water and then
dry the faucet with soft cotton cloths.
3. Do not use any abrasive cleansers, cloths, or paper towel.
4. Do not use any acid or abrasive detergent.
Turn off water and relieve pressure! Detach handle button
using a small flathead screwdriver, unscrew set screw
using Allen Wrench and take off handle.
Remove handles. Unscrew Dome Cap counter clockwise
by hand. Unscrew Retaining Nut using adjustable wrench,
take out cartridge assembly and inspect. Replace parts
as necessary. Reassemble parts by reversing steps.
Handle Removal Maintenance Valve Cartridge Removal Maintenance
G
A
B
D
F
K
Optional accessories
G- Spray Seat
Flexible Hoses(1)
E
I- Support
C
I
or
C
J
K- Allen wrench
J- Washer
H
L- Pipe plug (Use it when side sprays are not installed.)
L
(Use it when side sprays
are not installed.)
Kitchen Faucet With Spray
Questions, problems, missing parts?
call Akicon Customer Service 8 a.m.-6p.m. EST, Monday-Friday
Phone: [phone], Email: [email protected]
AKICONSHOP.COM
Model: 96918P1
96918P2
96918P3

is placed onto the bottom of base ring. Install
3
Open the valve, then turn the handle according to the
sign of C and H on the handle to regulate the temperature
of the water. (C=Cold,H=Hot)
.
6
Close Open
Swing Spout
7
After installation is complete, remove aerator and rotate
handle to the closed position. Then
turn on the water supply
valves, and check all connections for a leak. Turn on
your faucet and allow both hot and cold water to run at
least one minute each, then Install the Aerator.
Faucet Start Up
INSTALLATION PROCEDURES
You should clean all the dirts from valve outlets.
Turning off the water supply valves. This is usually
found near the water meter. If you are replacing
an existing faucet, remove the faucet from the
sink and clean the sink surface thoroughly.
Install without deck plate. Make sure the O-ring
faucet through hole in sink. From underside sink,
put Plastic Washer and mounting nut. Position
faucet on sink properly and tighten mounting nut.
If necessary, tighten screws using a adjustable
wrench until the faucet is firmly connected to the
sink.
Connect the hot and cold water supply lines of the faucet
to the water supply valves.
2
1 2
3
5
4A
Install with deck plate. Place a bead of plumber’s
putty between faucet and sink. Place deck plate
over the three holes of sink.
2A
Make sure the O-ring is placed onto the bottom
of base ring. Install faucet through deck plate.
From underside sink, put plastic washer and
mounting nut. Position faucet on sink properly
and tighten mounting nut.
2B
Insert spray seat through far right-hand hole on sink,
then tighten mounting nut using adjustable wrench.
Insert spray hose down through spray seat, then connect
the spray hose to the outlet hose at the bottom of the tap
and tighten it.
4B
If you do not want to install the spray, please use the plug
"L" to block-off and tighten it.
If you do not want to install the spray.
Install side spray.
Pipe plug