Aktakom ACM-2047 User manual

Clamp Meter
ACM-2047
USER’S MANUAL
www.tmatlantic.com

EN 61010-2-032
CAT II 600V
CAT III 300V
Pollution Degree 2
SYMBOLS showed onthe clamp meter or in this manual:
Caution, risk of danger.
Refer to accompanying documents
Caution, risk of electric shock.
Double Insulation
Application around and removal from HAZARDOUS
LIVE conductors is permitted.
Earth (ground)
AC (Alternating Current)
DC (Direct Current)
Both direct and alternating current
Conforms to relevant European Union directives.
Do not dispose of this clamp meter as unsorted
municipal waste. Contact a qualified recycler for
disposal.
www.tmatlantic.com

1
Overvoltage Category I (CAT I):
Equipment for connection to circuits in which measures are
taken to limit the transient overvoltages to an appropriate low level.
Overvoltage Category II (CAT II):
Energy-consuming equipment to be supplied from the fixed
installation.
Overvoltage Category III (CAT III):
Equipment in fixed installations.
SAFETY INFORMATION: (Read First Before Operation)
Please follow the following instructions carefully for safe operation.
■NEVER use the clamp meter for Voltages higher than 600V.
■DO NOT hold the clamp meter beyond its tactile barrier.
■DO NOT use the clamp meter and accessories if they look
damaged.
■USE CAUTION when working with high voltages.
■USE CAUTION when measuring the voltages higher than
30VAC rms or 60VDC. These voltages pose a shock hazard.
■USE EXTREME CAUTION when working around bare
conductors or bus bars.
■ALWAYS use the clamp meter as the instructions in the manual.
WARNING: If the clamp meter is used in a manner
Not specified by the manufacturer, the protection
Pro vid ed by th e clamp meter ma y be impaired .
www.tmatlantic.com

1
TABLEOFCONTENTS
I.Features................................................................................................................... 1
II.PanelDescription................................................................................................. 2
III.OperationInstructions......................................................................................... 4
3.1 DC/AC Current Measurements ..................................................................... 4
3.2 Frequency (Hz) Measurement ....................................................................... 4
3.3 Relative Reading Measurements .................................................................. 5
3.4 Holding the LCD Reading .............................................................................. 5
3.5 Finding the MAX/MIN Value .......................................................................... 5
IV.Specifications....................................................................................................... 6
V.BatteryReplacement............................................................................................ 8
VI.Maintenance&Cleaning..................................................................................... 8
I.Features
1. Accurate DC/AC digital clamp meter for current measurement.
2. DC 10mA, AC 1mA high resolution .
3. True RMS reading for sine wave, symmetrical square wave, and triangular
wave etc.
4. Non-contact frequency measurements.
5. One touch zero for DCA adjustment.
6. 23 mm diameter jaw.
7. Large 3 3/4 digits LCD
8. Fast bargraph display (20 times/sec.) for transient observation.
9. Max/Min and Data Hold functions.
10.Easy single rotary switch for any function selection.
11. Ideal for works in crowded switch box or cable areas.
www.tmatlantic.com

2
II.PanelDescription
1. Transformer Jaw
This is used to pick up current signal. To measure DC/AC current, conductor
must be enclosed by the jaw.
2. Transformer Trigger
This is used to open the jaw.
3. Function Selector Switch
This is the on/off switch and used to select the function user desired, such as DCA,
ACA, DCV, ACV, Hz, Ohm and Continuity.
4. Data Hold Button
Once this button is pushed, reading shall be held on the LCD. Press again to
release it.
5. Max/Min Hold Button
This button is used to enable the maximum or minimum value to be displayed and
updated during measurement. Press once, minimum value shall be displayed and
updated. Press again, maximum value shall be displayed and updated. Press
again (the third push), clamp meter return to normal measurement mode. If
MAX/MIN function is enabled, theZERO/Relative function will be disabled.
6. Zero/Relative Button
Once this button is pressed, the current reading shall be set to zero and be used
as a zero reference value for all other subsequent measurement. The function is
also used to remove offset value caused by the residual magetism remained in
the core for the DC current measurement. Zero/Relative Button will be disabled if
MAX/MIN function is enabled.
tactile barrier
www.tmatlantic.com

3
7. LCD
This is a 3 3/4 digit Liquid Crystal Display with maximum indication of 3999.
Function symbols, units, bargraph, sign, decimal points, low battery symbols,
max/min symbols, and zero symbol are included.
8. Low Battery Symbol
When this symbol appears, it means the battery voltage drops below the minimum
required voltage. Refer to Section V for battery replacement.
9. Zero/Relative Symbol
When this symbol appears, it means a reference value has been subtracted from
the actual reading. The reading shown is a offseted value. Press and hold the
zero button for 2 seconds to disable this function.
10. Data Hold Symbol
Once the hold button is pressed, this symbol appears on LCD.
11. 40 segments Bargraph
Bargraph has forty segments. It displays segments proportional to the actual
reading. Each segment represent one hundred counts.
12. Max/Min Hold Symbol
Once the max/min button is pressed, either MAX or MIN shall be displayed on
LCD
13. Continuity Symbol
If ohm and continuity function is selected, this symbol shall appears on LCD.
14. Units Symbols
Once a function is selected, corresponding unit (V, , A, or Hz) shall be displayed
on LCD.
15.Hand Strap
Put your hand through the hole of hand strap to avoid accidental drop of the clamp
meter.
www.tmatlantic.com

4
III.OperationInstructions
3.1 DC/AC Current Measurements
3.1.1 DC Current
a. Set the rotary switch at appropriate DC range.
b. Push the zero button to adjust the reading to zero.
c. Press the trigger to open the jaw and fully enclose the conductor to be
measured. No air gap is allowed between the two half jaws.
d. Read the DCA value from the LCD display.
3.1.2 AC Current
e. Set the rotary switch at appropriate AC range.
f. Press the trigger to open the jaw and fully enclose the conductor to be
measured. No air gap is allowed between the two half jaws.
g. Read the ACA value from the LCD display.
3.2 Frequency (Hz) Measurement
h. Make sure there is at least 0.1A AC current flowing through the
conductor by taking ACA measurement first.
www.tmatlantic.com

5
i. Set the rotary switch at Hz.
j. Press the trigger to open the jaw and fully enclose the conductor to be
measured. If line frequency is to be measured, enclose only one line of the
line source and make sure there is current flowing.
k. Read the Hz value from the LCD display.
3.3 Relative Reading Measurements
The zero button also can be used to make a relative measurement. Once the
button is pushed, the current reading is set to zero and a zero symbol shall be
displayed on LCD. All the subsequent measurement shall be displayed as a
relative value with respect to the value being zeroed. Press the zero button for
2 seconds to return to normal mode. Zero/Relative function will be disabled, if
MAX/MIN function is enabled.
3.4 Holding the LCD Reading
Press the HOLD button, then the reading shall be hold and kept on LCD.
3.5 Finding the MAX/MIN Value
Press the MAX/MIN button to enable the maximum and minimum values to be
recorded and updated during measurement. Push the button once, the
maximum value shall be displayed and updated.. Push again (second push),
the minimum value shall be displayed. Push again (third push), MAX/MIN
function shall be disabled and return to the normal measurement mode.
Zero/Relative function will be disabled, if MAX/MIN function is enabled.
www.tmatlantic.com

6
IV.Specifications(23C±5C)
DC Current:
Range
Resolution
Accuracy
Overload Protection
40A
10mA
±1.0%±2dgts
DC 400A
400A (0-150A)
100mA
±1.0%±2dgts
DC 400A
400A (150-200A)
100mA
±2.2%±2dgts
DC 400A
400A (200-400A)
100mA
±4.0%±2dgts
DC 400A
AC Current (TrueRMS, CrestFactor <= 4):
Accuracy
Overload
Protection
Range
Resolution
50/60 Hz
40 - 1KHz
4A(0-500mA)
1mA
±1.5%±7dgts
±2.0%±7dgts
AC 400A
4A(500mA-4A)
1mA
±1.5%±3dgts
±2.0%±4dgts
AC 400A
40A
10mA
±1.5%±3dgts
±2.0%±4dgts
AC 400A
100A (0-100A)
100mA
±1.5%±3dgts
±2.0%±4dgts
AC 500A
400A (100-200A)
100mA
±2.2%±3dgts
±2.5%±4dgts
AC 500A
400A (200-400A)
100mA
±4.0%±3dgts
±5.0%±4dgts
AC 500A
Frequency (auto range):
Range (Hz)
Resolution
(Hz)
Accuracy
Sensitivity
Overload Protection
99.99-99.9
K
0.01 - 10
±0.5%±2dgts
0.3A
AC 500A
Indoor Use
Conductor Size: 23mm max. (approx.)
Battery Type: two 1.5V SUM-3
Display: 3 3/4 LCD with 40 seg. Bargraph
Range Selection: manual
Overload Indication: left most digit blinks
Power Consumption: 10 mA (approx.)
Low battery Indication:
Sampling Time: 2 times/sec (display)
20 times/sec. (bargraph)
Operating Temperature: -10C to 50C
www.tmatlantic.com

7
Operating Humidity: less than 85% relative
Storage Temperature: -20C to 60C
Storage Humidity: less than 75% relative
Altitude up to 2000M
Dimension: 183mm(L)x61.3mm (W) x 35.6mm (H)
7.2" (L) x 2.5" (W) x 1.4" (H)
Weight: 190g (battery included)
Accessories: Carrying bag x 1
Users manual x 1
1.5V battery x 2
www.tmatlantic.com

8
V.BatteryReplacement
When the low battery symbol is displayed on the LCD, replace the old batteries with
two new batteries.
A. Turn the power off and remove the test leads from the clamp meter.
B. Remove the screw of the battery compartment.
C. Lift and remove the battery compartment.
D. Remove the old batteries.
E. Insert two new 1.5V SUM-3 batteries.
F. Replace the battery compartment and secure the screw.
VI.Maintenance&Cleaning
Servicing not covered in this manual should only be performed by qualified
personnel. Repairs should only be performed by qualified personnel.
Periodically wipe the case with a damp cloth and detergent; do not use abrasives or
solvents.
Address of Agent, Distributor, Importer, or Manufacturer
www.tmatlantic.com