Aktakom ATA-2504 User manual

Clamp Meter
www.tmatlantic.com

1
EN 61010-2-032
CAT II 600V
CAT III 300V
Pollution Degree 2
SYMBOLS showed on the clamp meter or in this manual:
Caution, risk of danger.
Refer to accompanying documents
Caution, risk of electric shock.
Double Insulation
Application around and removal from HAZARDOUS
LIVE conductors is permitted.
Earth (ground)
AC (Alternating Current)
DC (Direct Current)
Both direct and alternating current
Conforms to relevant European Union directives.
Do not dispose of this clamp meter as unsorted
municipal waste. Contact a qualified recycler for
disposal.
www.tmatlantic.com

2
Overvoltage Category I (CAT I):
Equipment for connection to circuits in which measures are
taken to limit the transient overvoltages to an appropriate low level.
Overvoltage Category II (CAT II):
Energy-consuming equipment to be supplied from the fixed
installation.
Overvoltage Category III (CAT III):
Equipment in fixed installations.
SAFETY INFORMATION: (Read First Before Operation)
Please follow the following instructions carefully for safe operation.
■ NEVER use the clamp meter for Voltages higher than 600V.
■ DO NOT hold the clamp meter beyond its tactile barrier.
■ DO NOT use the clamp meter and accessories if they look
damaged.
■ USE CAUTION when working with high voltages.
■ USE CAUTION when measuring the voltages higher than
30VAC rms or 60VDC. These voltages pose a shock hazard.
■ USE EXTREME CAUTION when working around bare
conductors or bus bars.
■ ALWAYS use the clamp meter as the instructions in the manual.
WARNING: If the clamp meter is used in a manner
Not specified by the manufacturer, the protection
Provided by the clamp meter may be impaired.
www.tmatlantic.com

3
TABLE OF CONTENTS
I.Features …………………………………………………………………………… 3
II. Panel Description ………………………………………………………………. 4
III. Operating Instructions ………………………………………………………… 5
A. DC Current Measurement ………………………………………………….. 5
B.AC Current Measurement ………………………………………………….. 5
C. Current Waveform Observation (Connected to an Oscilloscope) ……….. 6
IV.Specifications ………………………………………………………………….. 6
V. Battery Replacement ………………………………………………………….. 8
VI. Maintenance & Cleaning …………………………………………………….. 8
I.Features
1. Accurate DC/AC current probe for currentmeasurement.
2. 10mADC, 1mAAC high resolution.
3. One touch zero for DCA adjustment.
4. 23 mm diameter jaw.
5. Easy single rotary switch for any function selection.
www.tmatlantic.com

4
II. Panel Description
1. TransformerJaw
To measure DC/AC current, enclose the conductor by the jaw.
2. TransformerTrigger
Push the trigger to open the jaw.
3. Zero Button
Push the zero button to zero the output voltage before measuring any current.
4. On/Off and Range Selection Switch
Turn the rotary switch to select the desired range.
5. Power-on LED
When the unit is turned on, this LED will be lighted.
6. Low Battery LED
When the battery voltage is lower than the required voltage, this LED will be lighted
while the power-on LED will be off.
7. Output Terminals
The output voltage is proportional to the current measured. Black terminal is the
signal ground while red terminal is the signal. Do not input any live voltage to
these terminals.
8. Hand Strap
Put your hand through the hole of the hand strap to avoid accidental drop of the
clamp meter.
tactile barrier
www.tmatlantic.com

5
III. Operating Instructions
A. DC Current Measurement
1.Set the rotary switch at 4A, 40A or 200A.
2.Plug one end of each test lead into themeter terminals
3.Plug in the other end of the test lead into a multimeter.
4.Make sure current probe's and multimeter's COM terminals
are connected.
5.Set the range of multimeter at 200 or 400 mVDC for DC current
measurement.
6.Push the zero button toadjust the reading of multimeter to zero.
7.Press the trigger to open the jaw and fully enclose the conductor to be
measured. No air gap is allowed between the two half jaws.
8. Read the measured value from the meter's display.
B. AC Current Measurement
1.Set the rotary switch at 4A, 40A or 200A.
2.Plug one end of each test lead into themeter terminals
www.tmatlantic.com

6
3.Plug in the other end of the test lead into a multimeter. It is strongly
recommended a TRUE RMS multimeter is used for AC current
measurement for more accurate reading.
4.Make sure current probe's and multimeter's COM terminals are connected.
5.Set the range of multimeter at 200 or 400 mVAC for AC current
measurement.
6.Press the trigger to open the jaw and fully enclose the conductor to be
measured. No air gap is allowed between the two half jaws.
7. Read the measured value from the meter's display.
C. Current Waveform Observation (Connected to an Oscilloscope)
1. Find a BNC converter which converts the test plugs into BNC connector.
2. Set the rotary switch at 4A, 40A or 200A.
3. Connect the test plugs into current probe's terminals.
4. Connect the other ends of test leads into BNC converter.
5. Connect the BNC converter into oscilloscope's input.
6. Make sure the polarities of current probe and oscilloscope are connected
correctly.
7.Press the trigger to open the jaw and fully enclose the conductor to be
measured. No air gap is allowed between the two half jaws.
8. Select appropriate voltage range(eg. mv/div) so that output (200mV or 400mV
full scale) from current probe can be observed from oscilloscope.
IV.Specifications(23°C±5°C)
Range Output Accuracy
DCA 0-4A1DC 100mV/A ±2.0%±0.005A
DCA 0-40A DC 10mV/A ±1.0%±0.02A
DCA 0-150A DC 1mV/A ±1.0%±0.2A
DCA 150-200A DC 1mV/A -2.2%±0.2A
ACA 0-4A AC 100mV/A ±2.0%±0.005A(40-1KHz)
ACA 0-40A AC 10mV/A ±1.5%±0.03A(40-1KHz)
ACA 0-150A AC 1mV/A ±1.5%±0.3A(40-1KHz)
ACA 150-200A AC 1mV/A -2.2%±0.3A(40-1KHz)
www.tmatlantic.com

7
This unit is not designed to measure DC 0-4A with resolution of DC 1mA. The
output voltage will change within 0.4mV.
Range Sensitivity
DCA 0-4A20.1mV/1mADC
DCA 0-40A 0.1mV/10mA DC
DCA 0-200A 0.1mV/100mA DC
ACA 0-4A 0.1mV/1mA AC
ACA 0-40A 0.1mV/10mA AC
ACA 0-200A 0.1mV/100mA AC
This unit is not designed to measure DC 0-4A with resolution of DC 1mA. The
output voltage will change within 0.4mV.
Indoor Use
Conductor Size: 23mm max. (approx.)
Battery Type: two 1.5V SUM-3 AA
Range Selection: manual
Power Consumption: 6 mA (approx.)
Low battery Indication: red LED lights
Operating Temperature: -10°C to 50°C
Operating Humidity: less than 85% relative
Altitude: up to 2000M
Storage Temperature: -20°C to 60°C
Storage Humidity: less than 75% relative
Dimension: 183mm(L)x61.3mm(W)x35.6mm (H)
7.2" (L) x 2.5" (W) x 1.4" (H)
Weight: 190g (battery included)
Accessories: Carrying bag x 1
Users manual x 1
Test leads
1.5V battery x 2
www.tmatlantic.com

8
V.Battery Replacement
When the low battery LED lights, replace the old batteries with two new batteries.
A. Remove the test leads from the current.
B. Remove the screw of the battery compartment.
C. Lift and remove the battery compartment.
D. Remove the old batteries.
E. Insert two new 1.5V SUM-3 batteries.
F. Replace the battery compartment and secure the screw.
VI. Maintenance & Cleaning
Servicing not covered in this manual should only be performed by qualified
personnel. Repairs should only be performed by qualified personnel.
Periodically wipe the case with a damp cloth and detergent; do not use abrasives or
solvents.
Address of Agent, Distributor, Importer, or Manufacturer
www.tmatlantic.com