Aktakom ATK-2021B User manual

User manual
Clamp meter
AТK-2021B
www.tmatlantic.com

EN61010-2-032
CATII600V
CATIII300V
Pollution Degree 2
SYMBOLS showed on the clamp meter or in this manual:
Caution, risk of danger.
Refer to accompanying documents
Caution, risk of electric shock.
Double Insulation
Application around and removal from HAZARDOUS
LIVE conductors is permitted.
Earth (ground)
AC (Alternating Current)
DC (Direct Current)
Both direct and alternating current
Conforms to relevant European Union directives.
Do not dispose of this clamp meter as unsorted
municipal waste. Contact a qualified recycler for
disposal.
www.tmatlantic.com

1
Overvoltage Category I (CAT I):
Equipment for connection to circuits in which measures are
taken to limit the transient overvoltages to an appropriate low level.
Overvoltage Category II (CAT II):
Energy-consuming equipment to be supplied from the fixed
installation.
Overvoltage Category III (CAT III):
Equipment in fixed installations.
SAFETY INFORMATION: (Read First Before Operation)
Please follow the following instructions carefully for safe operation.
■NEVER use the clamp meter for Voltages higher than 600V.
■DO NOT hold the clamp meter beyond its tactile barrier.
■DO NOT use the clamp meter and accessories if they look
damaged.
■USE CAUTION when working with high voltages.
■USE CAUTION when measuring the voltages higher than
30VAC rms or 60VDC. These voltages pose a shock hazard.
■USE EXTREME CAUTION when working around bare
conductors or bus bars.
■ALWAYS use the clamp meter as the instructions in the manual.
WARNING: If the clamp meter is used in a manner
Not specified by the manufacturer, the protection
Provided by the clamp meter may be impaired.
www.tmatlantic.com

2
TABLE OF CONTENTS
1. Features .......................................................................................................... 2
2. Panel Description ............................................................................................. 3
3. Operation Instructions....................................................................................... 6
3.1. DC/AC Current Measurements ............................................................. 6
3.2. DC/AC Voltage Measurements ............................................................. 7
3.3. Capacitance Measurement................................................................... 8
3.4. Temperature Measurement................................................................... 9
3.5. Resistance Measurement................................................................... 10
3.6. Continuity Test.................................................................................... 10
3.7. Frequency (Hz) Measurement ............................................................ 10
3.8. Duty Measurement............................................................................. 10
3.9. Diode Test.......................................................................................... 10
3.10. Relative Reading Measurements .......................................................11
3.11. Holding the LCD Reading ..................................................................11
3.12. Finding the MAX/MIN Value...............................................................11
3.13. Change from Auto-range Mode to Manual Mode ................................11
3.14. Disable Auto-power-off.......................................................................11
4. Specifications(23°C ± 5°C )............................................................................ 12
5. Battery Replacement...................................................................................... 15
6. Maintenance & Cleaning................................................................................. 15
1. Features
1. 10 mA high resolution on 40A DC/AC range
2. Temperature (℃or ℉)and Capacitance.
3. One touch zero for DCA adjustment.
4. Auto-range for V, A, Ω, F, and temperature.
5. 23 mm diameter jaw.
6. Auto-power-off (15 minutes)
7. Fast bargraph display (30 times/sec.) for transient observation.
8. Continuity and frequency measurements.
9. Max/Min and Data Hold functions.
10. 600V overload protection for ohm measurement.
11. Ideal for works in crowded switch box or cable areas.
www.tmatlantic.com

3
2. Panel Description
1. Transformer Jaw
This is used to pick up current signal. To measure DC/AC current, conductor
must be enclosed by the jaw.
2. Transformer Trigger
This is used to open the jaw.
3. Function Selector Switch
This is used to select the function user desired, such as DCA, ACA, DCV, ACV,
Hz, Ohm and Continuity.
4. AC/DC Select Switch
This is used to select AC or DC voltage or current, Hz or Duty, Ohm or Continuity,
Capacitance or Diode, ℃or ℉.
5. Data Hold Button
Once this button is pushed, reading shall be held on the LCD. Press again to
release it. This button is not available in continuity or diode function.
6. MAX/MIN Hold Button
This button is used to enable the maximum or minimum value to be displayed and
updated during measurement. Press once, minimum value shall be display and
T
www.tmatlantic.com

4
updated. Press again, maximum value shall be displayed and updated. Zero
function will be disabled if MAX/MIN is enabled. This button is not available in duty,
hz, continuity, diode or capacitance function.
7. VΩRANGE Zero/Relative Button
On voltage or ohm function, press this button to select manual range.
On other functions, once this button is pressed, the current reading shall be set to
zero and be used as a zero reference value for all other subsequent
measurement. The function is also used to remove offset value caused by
residual magnetism remaining in the core for the DC current measurement. The
Zero/Relative function will be disabled if the MAX/MIN button is pressed. This
button is not available in duty, hz, continuity, diode function.
8. LCD
This is a 3 3/4 digit Liquid Crystal Display with maximum indication of 3999.
Function symbols, units, bargraph, sign, decimal points, low battery symbols,
max/min symbols, and zero symbol are included.
9. Low Battery Symbol
When this symbol appears, it means the battery voltage drops below the
minimum required voltage. Refer to Section 5 for battery replacement.
10. Zero/Relative Symbol
When this symbol appears, it means a reference value has been subtracted from
the actual reading. The reading shown is an offset value. Press the zero button
again to disable this function.
11. Data Hold Symbol
Once this button is pressed, this symbol appears on LCD.
12. Bargraph
Bargraph has forty segments. It displays segments proportional to the actual
reading. Each segment represents one counts.
13. Max/Min Hold Symbol
Once the max/min button is pressed, either MAX or MIN shall be displayed on
LCD.
14. Continuity Symbol
If continuity function is selected, this symbol shall appear on LCD.
15. Units Symbols
Once a function is selected, corresponding unit (V, W, A, or Hz) shall be displayed
on LCD.
16. V, Ω, Hz, Capacitance, Temperature input Terminal
This terminal is used as input for voltage, ohm/continuity, frequency, capacitance
or temperature measurements.
17. COM Terminal
This terminal is used as common reference input.
www.tmatlantic.com

5
18. Hand Strap
Put your hand through the hole of hand strap to avoid accidental drop of the clamp
meter.
www.tmatlantic.com

6
3. Operation Instructions
3.1. DC/AC Current Measurements
WARNING: Make sure that all the test leads are disconnected from the meter's
terminals for current measurement.
3.1.1 DC Current
a. Set the rotary switch at 40A or 200A and move the sliding switch to DC
b. Push the zero button to adjust the reading to zero.
c. Press the trigger to open the jaw and fully enclose the conductor to be
measured. No air gap is allowed between the two half jaws.
d. Read the measured value from the LCD display.
T
www.tmatlantic.com

7
3.1.2. AC Current
a. Set the rotary switch at 40A or 200A and move the sliding switch to
AC.
b. Press the trigger to open the jaw and fully enclose the conductor to
be measured. No air gap is allowed between the two half jaws.
c. Read the measured value from the LCD display.
3.2. DC/AC Voltage Measurements
WARNING: Maximum input for DC V is 600, and for AC V is 600. Do not attempt
to take any voltage measurement that exceeds the limits. Exceeding the limits
could cause electric shock and damage to the clamp meter.
3.2.1.DC Voltage
a. Set the rotary switch at V DC.
b. Insert the test leads into the input jack.
c. Connect the test prods of the test leads in PARALLEL to the circuit to be
measured.
d. Read the measured value from the LCD display.
3.2.2. AC Voltage
a. Set the rotary switch at V AC.
www.tmatlantic.com

8
b. Insert the test leads into the input jack.
c. Connect the test prods of the test leads in PARALLEL to the circuit to be
measured.
d. Read the measured value from the LCD display.
3.3. Capacitance Measurement
T
104
a. Plug the adapter into the terminal
b. Insert the capacitor into the adapter.
c. If the capacitance is less than 4nF, press ZERO (capacitance) button to
zero the residual capacitance.
d. Read the value from LCD.
www.tmatlantic.com

9
3.4. Temperature Measurement
T
a. Plug the adapter into the terminal
b. Insert the K-type thermal couple into the adapter
c. Read the temperature from LCD.
WARNING: Before taking any in-circuit resistance measurement, remove power
from the circuit being tested and discharge all the capacitors.
www.tmatlantic.com

10
3.5. Resistance Measurement
3.5.1. Set the rotary switch at Ω.
3.5.2. Insert the test leads into the input jack.
3.5.3. Connect the test prods of the test leads to the two ends of the resistor or
circuit to be measured.
3.5.4. Read the measured value from the LCD display.
3.6. Continuity Test
3.6.1. Turn the rotary switch to Ωposition and move the sliding switch to AC
position.
3.6.2. Insert the test leads into the input jack.
3.6.3. Connect the test probes of the test leads to the two ends of the resistor or
circuit to be measured.
3.6.4. Read the measured value from the LCD display.
3.6.5. If the resistance is lower than 10Ω,a beeping sound shall be heard.
3.7. Frequency (Hz) Measurement
3.7.1. Set the rotary switch at Hz.
3.7.2. Insert the test leads into the input jack.
3.7.3. Connect the test prods of the test leads in PARALLEL to the signal or
circuit to be measured.
3.7.4. Read the measured value from the LCD display.
3.8. Duty Measurement
3.8.1. Set the rotary switch at Duty.
3.8.2. Insert the test leads into the input jack.
3.8.3. Connect the test prods of the test leads in PARALLEL to the signal or
circuit to be measured.
3.8.4. Read the measured value from the LCD display.
3.9. Diode Test
3.9.1. Set the rotary switch at diode.
3.9.2. Insert the test leads into the input jack.
3.9.3. Connect the test prods of the test leads to the two ends of a diode.
3.9.4. Read the diode voltage from LCD.
www.tmatlantic.com

11
3.10. Relative Reading Measurements
The zero button also can be used to make a relative measurement. Once the
button is pushed, the current reading is set to zero and a zero symbol shall be
displayed on LCD. All the subsequent measurement shall be displayed as a
relative value with respect to the value being zeroed. Press the zero button again
to return to normal mode. But this function is disabled if MAX/MIN function is
enabled. Please watch for symbol displayed on LCD.
3.11. Holding the LCD Reading
Press the HOLD button, then the reading will be hold and kept on LCD.
3.12. Finding the MAX/MIN Value
Press the MAX/MIN button to enable the maximum and minimum values to be
recorded and updated during measurement. Push the button once, the
maximum value shall be displayed and updated. The LCD display toggles
between the MAX and MIN values. To exit MAX/MIN function, press and hold the
MAX/MIN button for more than 2 seconds. If MAX/MIN button is pressed, the
ZERO function will be disabled and the ZERO symbol will disappear from LCD.
3.13. Change from Auto-range Mode to Manual Mode
If users want to select certain range for specific measurement, they can press the
VΩRANGE button to select appropriate range. To return to auto-range, press and
hold the VΩRANGE button for 2 seconds.
3.14. Disable Auto-power-off
The meter will turn itself off 15 minutes after power-on (A symbol of APO is
displayed in LCD). Also pressing any button or turning the rotary switch will reset
the 15 minute timer.
To disable the Auto-Power-Off function, hold the HOLD button while turning on
power.
www.tmatlantic.com

12
4. Specifications(23°C ± 5°C )
DC Current:
Range Resolution Accuracy Overload Protection
40 A 10mA ±1.5%±2dgts DC 400A
0-150 A 100mA ±1.5%±2dgts DC 400A
150-200 A 100mA ±2.2%±2dgts DC 400A
AC Current:
AccuracyRange Resolution
50/60 Hz 40 - 1KHz
Overload
Protection
40A 10mA ±1.5%±3dgts ±2.0%±4dgts AC 400A
0-150A 100mA ±1.5%±3dgts ±2.0%±4dgts AC 400A
150-200A 100mA ±2.2%±3dgts ±2.5%±4dgts AC 400A
DC Voltage: (Overload Protection: 600V)
Range Resolution Accuracy Input Impedance
400mV 0.1 mV ±1.5%±3dgts 2.3MΩ
4V 1 mV ±1.5%±3dgts 2.3MΩ
40V 10 mV ±1.5%±3dgts 2.3MΩ
400V 100 mV ±1.5%±3dgts 2.3MΩ
600V 1V ±1.5%±3dgts 2.3MΩ
AC Voltage: (Input Impedance: 2.3 MΩ)
Accuracy
Range Resolution
50/60 Hz 40 - 1KHz
Overload
Protection
0.01-4V 1mV ±1.5%±5dgts ±2.0%±5dgts AC 800V
40V 10mV ±1.5%±5dgts ±2.0%±5dgts AC 800V
400V 100mV ±1.5%±5dgts ±2.0%±5dgts AC 800V
600V 1V ±1.5%±5dgts ±2.0%±5dgts AC 800V
¹400mV range is not designed for AC measurement.
Continuity: (open voltage 0.4V, Overload Protection AC 600V)
Range Resolution Accuracy Beeping
40-400Ω0.1Ω±1.0%±2dgts <10.0Ω(approx.)
www.tmatlantic.com

13
Resistance (Ω):(open voltage 0.4V)
Range Resolution Accuracy Overload Protection
400Ω0.1Ω±1.5%±2dgts AC 600V
4KΩ1Ω±1.5%±2dgts AC 600V
40KΩ10Ω±1.5%±2dgts AC 600V
400KΩ100Ω±1.5%±2dgts AC 600V
4MΩ1KΩ±1.5%±2dgts AC 600V
40MΩ10KΩ±1.5%±2dgts AC 600V
Frequency:
Range
(Hz)
Resolution
(Hz) Accuracy Sensitivity O.L Protection
1-100K 0.001 – 100 ±0.5%±2dgts 5V AC 600V
Duty:
Range(<10KHz) Resolution Accuracy Sensitivity
1 – 99% 0.1% 10d 10V
Temperature: (K Type Thermal Couple with Adapter, ℃or ℉ )
Range Resolution Accuracy Overload Protection
-40 – 0 ℃0.1 ℃ ±2.0%±2 ℃AC 600V
0 – 400 ℃0.1 ℃ ±0.5%±2 ℃AC 600V
400 – 1000 ℃1 ℃ ±0.5%±2 ℃AC 600V
-40 – 0 ℉0.1 ℉±2.0%±4 ℉AC 600V
0 – 400 ℉0.1 ℉±0.5%±4 ℉AC 600V
400 – 1800 ℉1℉±0.5%±4 ℉AC 600V
Capacitance:
Range Resolution Accuracy Overload Protection
40nF 10pF ±5.0%±0.2 nF AC 600V
400nF 0.1nF ±3.0%±0.2 nF AC 600V
4μ1nF ±3.0%±0.02μFAC 600V
40μF10nF ±3.0%±0.02μFAC 600V
400μF100nF ±3.0%±0.2μFAC 600V
www.tmatlantic.com

14
Diode Test:
Range Resolution Accuracy Overload Protection
0 – 1.999V 0.001V ±2.5%±5dgts AC 600V
Conductor Size: 23mm max. (approx.)
Battery Type: two 1.5V SUM-3
Display: 3 3/4 LCD with 40 seg. Bargraph
Range Selection: manual
Overload Indication: OL
Power Consumption: 10 mA (approx.)
Low battery Indication:
SamplingTime: 3times/sec.(display)
30 times/sec. (bargraph)
Auto-Power-Off: 15 minutes
Operating Temperature: -10°C to 50°C
Operating Humidity: less than 85% relative
Altitude: up to 2000M
Storage Temperature: -20°C to 60°C
Storage Humidity: less than 75% relative
Dimension: 183mm(L)x63.6mm (W) x 35.6mm (H)
7.2" (L) x 2.5" (W) x 1.4" (H)
Weight: 190g (battery included)
Accessories: Adapter
(forCapacitanceandK-typeThermalCouple)
Carryingbagx1
Users manual x 1
1.5V battery x 2
www.tmatlantic.com

15
5. Battery Replacement
When the low battery symbol is displayed on the LCD or LCD display is dark,
replace the old batteries with two new batteries.
5.1. Turn the power off and remove the test leads from the clamp meter.
5.2. Remove the screw of the battery compartment.
5.3. Lift and remove the battery compartment.
5.4. Remove the old batteries.
5.5. Insert two new 1.5V SUM-3 batteries.
5.6. Replace the battery compartment and secure the screw.
6. Maintenance & Cleaning
Servicing not covered in this manual should only be performed by qualified
personnel. Repairs should only be performed by qualified personnel.
Periodically wipe the case with a damp cloth and detergent; do not use abrasives or
solvents.
Address of Agent, Distributor, Importer, or Manufacturer
www.tmatlantic.com