Alcatel-Lucent 9927 Instruction Manual

APPLICANT: Alcatel-Lucent EXHIBIT 3 FCC ID: AS5BBTRX-05
Page 1 of 1
EXHIBIT 3
Section 2.1033 (c)(3) INSTALLATION AND OPERATING INSTRUCTIONS
A copy of the installation and operating instructions to be furnished to the user. A draft copy of the
instructions may be submitted if the actual document is not available. The actual document shall be
furnished to the FCC when it becomes available.
Response
A copy of the “Alcatel-Lucent 9927 Distributed Base Station Outdoor Site Preparation Guidelines” manual
is attached to this exhibit.

Title page
Alcatel-Lucent 9927 Distributed Base Station
Outdoor Site Preparation Guidelines
401-703-516
Issue 1 | March 2012
Alcatel-Lucent – Proprietary
Use pursuant to applicable agreements
Use pursuant to applicable agreements

Legal notice
Legal notice
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective
owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright © 2012 Alcatel-Lucent. All rights reserved.
Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside
Alcatel-Lucent without its written authorization.
Not to be used or disclosed except in accordance with applicable agreements.
Notice
Every effort was made to ensure that the information in this Information Product (IP) was complete and accurate at the time of printing. However,
information is subject to change.
Ordering information
The ordering number for this document is 401-703-516. To order this or other Alcatel-Lucent information products, see “To obtain documentation, training,
and technical support or submit feedback” on the Flexent®/AUTOPLEX®Wireless Networks System Documentation CD-ROM, 401-010-001 or the
documentation web site at (https://wireless.support.lucent.com/amps/rls_info/rls_doc/cd_docs/customer.support/customer.support_toc.pdf.wen).
Technical support
For technical support, see “To obtain documentation, training, and technical support or submit feedback” on the Flexent®/AUTOPLEX®Wireless Networks
System Documentation CD-ROM, 401-010-001 or the documentation web site at ( (https://wireless.support.lucent.com/amps/rls_info/rls_doc/cd_docs/
customer.support/customer.support_toc.pdf.wen).
Use pursuant to applicable agreements
Alcatel-Lucent – Proprietary
Use pursuant to applicable agreements

About this documentAbout this document
Purpose
This Information Product (IP) describes the basic site requirements that should be used to
plan a Alcatel-Lucent 9927 Distributed Base Station outdoor site. This document includes
specific tasks that should be completed at the job site before an installation can begin.
Reason for reissue
This document is Alcatel-Lucent 9927 Distributed Base Station Outdoor Site Preparation
Guidelines, document number 401-703-516, Issue 1. This issue incorporates information
available as of December 2011.
This is the second issue of this document. Whenever this document is reissued, the
reasons for reissue will be provided in this section.
The reasons for reissue are shown in the table below.
Issue Reason
2
Intended audience
This IP is intended for customers preparing a 9927 Distributed Base Station outdoor site.
Conventions used
The following conventions are used in this IP:
Measurements
All measurements are shown in metric form, and are followed by the English conversion
in parentheses.
...................................................................................................................................................................................................................................
9927 Dist BTS Outdoor
401-703-516
Issue 1 March 2012
Alcatel-Lucent – Proprietary
Use pursuant to applicable agreements xi

Naming conventions
In this IP, the Alcatel-Lucent 9927 Distributed Base Station Outdoor Cabinet is referred
to as 9927 Distributed Base Station Outdoor Cabinet.
Standard cross-sections and wire diameters of round copper conductors
The following table is from CEI/IEC 60947-1:2004, Table 1, Standard cross-sections of
round copper conductors and approximate relationship between mm2and AWG/kcmil
sizes for reference. Additional wire sizes are included in this information product as
appropriate for the topic.
ISO rated cross-sectional area (mm2) AWG/kcmil size
0.2 24
0.34 22
0.5 20
0.75 18
1-
1.5 16
2.5 14
412
610
10 8
16 6
25 4
35 2
-1
50 0 (1/0)
70 00 (2/0)
95 000 (3/0)
- 0000 (4/0)
120 250 kcmil
150 300 kcmil
185 350 kcmil
- 400 kcmil
240 500 kcmil
300 600 kcmil
About this document
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
xii Alcatel-Lucent – Proprietary
Use pursuant to applicable agreements
9927 Dist BTS Outdoor
401-703-516
Issue 1 March 2012