Alcatel-Lucent 1850 TSS-60 User guide

Alcatel-Lucent 1850
Transport Service Switch (TSS-60) | Release 2.0
Installation and System Turn-Up Guide
365-372-603R2.0
CC109696583
ISSUE 1
JANUARY 2009

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners..
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright © 2009 Alcatel-Lucent. All Rights Reserved.
Conformance statement
Interference Information: Part 15 of FCC Rules
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the guidelines in this document, the
equipment may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at the expense of the user.
Security Statement
In rare instances, unauthorized individuals make connections to the telecommunications network through the use of access features. In such an event, applicable
tariffs require that the customer pay all network charges for traffic. Alcatel-Lucent and its predecessors cannot be responsible for such charges and will not
make any allowance or give any credit for charges that result from unauthorized access.
Limited Warranty
Alcatel-Lucent provides a limited warranty to this product. For terms and conditions of sale, contact your Alcatel-Lucent Account Team.
Ordering Information
For more ordering information, refer to “How to order” in the section titled “About this document”
Developed by Alcatel-Lucent

iii
365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
Contents
About this document
Purpose ........................................................................................................................................................ xi
Reason for reissue ....................................................................................................................................... xi
Intended audience ........................................................................................................................................ xi
How to use this document .......................................................................................................................... xii
Safety information ......................................................................................................................................xiv
Conventions used .........................................................................................................................................xv
Related information .....................................................................................................................................xv
Document support ..................................................................................................................................... xvi
Technical support ...................................................................................................................................... xvi
How to order .............................................................................................................................................. xvi
How to comment ....................................................................................................................................... xvi
Packaging collection and recovery requirements ..................................................................................... xvii
Recycling/take-back/disposal of product ................................................................................................. xvii
1Safety
Laser safety ............................................................................................................................................... 1-2
Electrostatic discharge ESD considerations .............................................................................................. 1-5
Laser product classification ..................................................................................................................... 1-10
Alcatel-Lucent 1850 TSS-60 optical specifications ................................................................................ 1-12
Part I: Physical and power installation
2 Physical installation
Planning ..................................................................................................................................................... 2-2
Inspection .................................................................................................................................................. 2-6
Alcatel-Lucent 1850 TSS-60 center divider .............................................................................................. 2-7
Alcatel-Lucent 1850 TSS-60 shelf installation ....................................................................................... 2-10
Power cable installation ........................................................................................................................... 2-17
Final operations ....................................................................................................................................... 2-20

............................................................................................................................................................................................................................................................
Contents
iv 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
3 Cable and fiber installation
Planning .................................................................................................................................................... 3-3
Connector references ................................................................................................................................. 3-6
Inspection .................................................................................................................................................. 3-7
DS1/EI cable installation .......................................................................................................................... 3-8
DS3/EC-1 cable installation .................................................................................................................... 3-16
DS1 and DS3 hybrid cable installation ................................................................................................... 3-35
10/100BASE-T Ethernet cable installation ............................................................................................. 3-42
IAO LAN and TCP/IP cable installation ................................................................................................. 3-46
Modem cable installation ........................................................................................................................ 3-50
Sync cable installation ............................................................................................................................ 3-52
Office alarm cable installation ................................................................................................................ 3-57
Miscellaneous (environmental) discrete telemetry cable installation ..................................................... 3-61
OC-3/OC-12/OC-48/OC-192 main optical fiber cable installation ........................................................ 3-66
OC-3/OC-12/OC-48 low-speed optical fiber cable installation .............................................................. 3-69
100/1000BASE-X optical fiber cable installation ................................................................................... 3-71
CIT (RS-232) cable installation .............................................................................................................. 3-73
Final operations ....................................................................................................................................... 3-75
4 Circuit pack installation
Description ................................................................................................................................................ 4-2
Powering ................................................................................................................................................... 4-3
Circuit pack compatibility ......................................................................................................................... 4-7
Initial circuit pack installation ................................................................................................................. 4-10
Part II: Stand-alone installation testing
5 Stand-alone node setup
Software installation ................................................................................................................................. 5-3
Circuit pack installation ............................................................................................................................ 5-4
Use of WaveStar®CIT software ................................................................................................................ 5-8
Circuit pack program version verification .............................................................................................. 5-12
Alcatel-Lucent 1850 TSS-60 shelf initialization .................................................................................... 5-14

Contents
v
365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
............................................................................................................................................................................................................................................................
6 Stand-alone installation testing
LBO software settings ............................................................................................................................... 6-5
Clearing alarms ......................................................................................................................................... 6-8
Local equipment and cross-connect tests ................................................................................................ 6-10
DS1/E1 testing ......................................................................................................................................... 6-11
DS3/EC1 testing ...................................................................................................................................... 6-17
LNW74 and LNW66 testing ................................................................................................................... 6-24
OC-3 low-speed testing ........................................................................................................................... 6-28
OC-12 low-speed testing ......................................................................................................................... 6-33
OC-48 low-speed testing ......................................................................................................................... 6-36
LED test ................................................................................................................................................... 6-41
Office alarm test ...................................................................................................................................... 6-43
Automatic protection switching and alarm test ....................................................................................... 6-48
Manual switching tests ............................................................................................................................ 6-52
External timing verification ..................................................................................................................... 6-56
Miscellaneous (environmental) discrete telemetry test ........................................................................... 6-59
Modem connection test ........................................................................................................................... 6-62
Final operations ....................................................................................................................................... 6-65
Part III: Network turn-up and testing
7 Connecting adjacent network elements
Fiber installation ........................................................................................................................................ 7-4
Optical transmission test (OC-192, OC-48, OC-12, OC-3) .................................................................... 7-11
Automatic protection switching test ........................................................................................................ 7-13
Manual switching tests ............................................................................................................................ 7-15
Final operations ....................................................................................................................................... 7-18
8 WDMX setup and testing: integration procedures
Turn-up and test the LNW785 8 channel OMD ........................................................................................ 8-4
Connecting the ring (Mains) to the WDMX ............................................................................................. 8-6
Removing provisioning and equipage from the LNW785 ........................................................................ 8-9

............................................................................................................................................................................................................................................................
Contents
vi 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
Part IV: Miscellaneous detailed installation procedure and reference
material
A Technical support
Technical assistance ..................................................................................................................................A-2
Accessing and navigating the On-Line Customer Support (OLCS) web site ...........................................A-7
Other technical support services .............................................................................................................A-12
B Fiber cleaning
Equipment requirements and recommendations .......................................................................................B-3
Safety instructions .....................................................................................................................................B-4
Cleaning/inspecting optical connectors ....................................................................................................B-5
Cleaning pluggable optics module ..........................................................................................................B-11
C PTM installation
PTM modules ............................................................................................................................................C-2
Install pluggable modules .........................................................................................................................C-5
D Installing fiber connectors and LBOs
LBOs .........................................................................................................................................................D-2
Fiber connections ......................................................................................................................................D-5
E Backplane pin replacement
Pin and connector background .................................................................................................................. E-2
Repair kits and tools .................................................................................................................................. E-4
Simple repair methods .............................................................................................................................. E-5
Replacement methods ............................................................................................................................... E-7
F Fiber labeling
Fiber description ....................................................................................................................................... F-2
Fiber labels ................................................................................................................................................ F-4
GL Glossary
GL Terms and definitions
IN Index

vii
365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
List of figures
1Safety
1-1 Static control wrist strap ............................................................................................................... 1-6
2 Physical installation
2-1 Shelf mount rear cover kit 849001367 ......................................................................................... 2-4
2-2 Bay mount rear cover kit 849001060 ........................................................................................... 2-5
2-3 Center divider ............................................................................................................................... 2-7
2-4 Center divider with circuit packs installed. .................................................................................. 2-8
2-5 Alcatel-Lucent 1850 TSS-60 mounting bracket positions - 23-Inch/19-Inch frame ................. 2-12
2-6 Fiber duct mounting ................................................................................................................... 2-13
2-7 Safety ground screw. .................................................................................................................. 2-14
2-8 Fiber spools ................................................................................................................................ 2-15
2-9 Heat baffle .................................................................................................................................. 2-16
2-10 Power connection ....................................................................................................................... 2-17
3 Cable and fiber installation
3-1 Connector types and pinouts ........................................................................................................ 3-6
3-2 DS1/E1 cable connectors ............................................................................................................. 3-9
3-3 DS1/E1 cable routing to the right ............................................................................................... 3-10
3-4 DS1/E1 cable routing to the left ................................................................................................. 3-10
3-5 DS3/EC-1 cable connections ..................................................................................................... 3-18
3-6 DS3/EC-1 cable routing to the right .......................................................................................... 3-18
3-7 DS3/EC-1 cable routing to the left ............................................................................................ 3-19
3-8 DS1 and DS3 hybrid cable connections ..................................................................................... 3-36
3-9 DS1 and DS3 hybrid cable routing ...........................................................................................3-36
3-10 10/100BASE-T/TX cable connections ....................................................................................... 3-43
3-11 10/100BASE-T cable routing ..................................................................................................... 3-43
3-12 IAO LAN/TCP-IP cable connection to rear of Alcatel-Lucent 1850 TSS-60 .......................... 3-47
3-13 Modem cable connection .......................................................................................................... 3-50
3-14 Sync cable connections .............................................................................................................. 3-53
3-15 Office alarm cable connections .................................................................................................. 3-58

............................................................................................................................................................................................................................................................
List of figures
viii 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
3-16 Office alarm cable routing ......................................................................................................... 3-58
3-17 Miscellaneous discrete cable connection .................................................................................. 3-62
3-18 Miscellaneous discrete cable routing ........................................................................................ 3-62
3-19 Optical fiber routing .................................................................................................................. 3-67
4 Circuit pack installation
4-1 Power connections on Alcatel-Lucent 1850 TSS-60 backplane .................................................. 4-4
4-2 Alcatel-Lucent 1850 TSS-60 shelf ............................................................................................... 4-9
6 Stand-alone installation testing
6-1 Alcatel-Lucent 1850 TSS-60 shelf backplane ........................................................................... 6-58
6-2 Miscellaneous (environmental) discrete functions ................................................................... 6-60
B Fiber cleaning
B-1 Cleaning the ferrule endface ........................................................................................................B-6
B-2 CleTop cleaner .............................................................................................................................B-7
B-3 Acceptability criteria for fiber cleaning .....................................................................................B-9
C PTM installation
C-1 Pluggable optics module ..............................................................................................................C-5
C-2 Module types ................................................................................................................................C-6
C-3 Latch type 3 .................................................................................................................................C-8
C-4 Latch type 4 ..................................................................................................................................C-8
C-5 Electrical PTM routing ..............................................................................................................C-11
D Installing fiber connectors and LBOs
D-1 LC-type connector ports on circuit pack ......................................................................................D-2
D-2 LC-type LBO ...............................................................................................................................D-3
D-3 LC-type LBO inserted into LC-type connector port ...................................................................D-3
D-4 Removing LC-type LBO from LC-type connector port ..............................................................D-4
D-5 LC-type fiber connector ...............................................................................................................D-5
D-6 LC-type fiber connection .............................................................................................................D-6

ix
365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
List of tables
1Safety
1-1 Laser classes ............................................................................................................................... 1-11
1-2 Alcatel-Lucent 1850 TSS-60 optical circuit pack laser safety specifications ............................ 1-12
1-3 Alcatel-Lucent 1850 TSS-60 optical PTM laser safety specifications ...................................... 1-13
1-4 Dispersion-limited receiver sensitivity for OC-192 DWDM PTMs .......................................... 1-20
2 Physical installation
2-1 Cable requirements and options ................................................................................................... 2-5
2-2 Power cable assemblies .............................................................................................................. 2-19
2-3 Power connections ...................................................................................................................... 2-19
3 Cable and fiber installation
3-1 Cable requirements and options ................................................................................................... 3-4
3-2 DS1/E1 cable assemblies ........................................................................................................... 3-11
3-3 DS1/E1 transmission connections .............................................................................................. 3-13
3-4 DS3/EC-1 cable assemblies ....................................................................................................... 3-20
3-5 Twenty-four cable DS3/EC-1 transmission connections ........................................................... 3-29
3-6 Twelve cable DS3/EC-1 transmission connections .................................................................... 3-33
3-7 DS1 and DS3 hybrid cable assemblies ....................................................................................... 3-38
3-8 DS1 and DS3 hybrid cable DS3 transmission connections ....................................................... 3-41
3-9 DS1 and DS3 hybrid cable DS1 transmission connections ....................................................... 3-41
3-10 10/100Base-T Ethernet cable assemblies ................................................................................... 3-44
3-11 10/100BaseT ethernet connections ............................................................................................ 3-45
3-12 LAN 10BaseT cable assemblies ................................................................................................. 3-47
3-13 LAN 10Base-T cross-over cable connections ............................................................................ 3-49
3-14 LAN 10Base-T straight-through cable connections ................................................................... 3-49
3-15 Modem cable assemblies ............................................................................................................ 3-51
3-16 Modem cable connections .......................................................................................................... 3-51
3-17 Synchronization cable assemblies (SYNC1 and SYNC2) ......................................................... 3-55
3-18 Synchronization cable (DS1 timing reference) connections ...................................................... 3-56
3-19 Office alarm cable assemblies .................................................................................................... 3-60

............................................................................................................................................................................................................................................................
List of tables
x365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
3-20 Alarm office connections ........................................................................................................... 3-60
3-21 Miscellaneous discrete cable assemblies ................................................................................... 3-64
3-22 Miscellaneous (environmental) discrete telemetry connections ................................................ 3-64
3-23 CIT cable assembly .................................................................................................................... 3-73
3-24 Standard CIT cable connection .................................................................................................. 3-74
3-25 RJ-45 to DB-9 connector connections ....................................................................................... 3-74
4 Circuit pack installation
4-1 Alcatel-Lucent 1850 TSS-60 shelf power supply requirements .................................................. 4-3
4-2 Release 2.0 circuit pack slot compatibility .................................................................................. 4-7
6 Stand-alone installation testing
6-1 Office alarm connections ........................................................................................................... 6-44
6-2 Miscellaneous (environmental) discrete telemetry connections ................................................ 6-61
7 Connecting adjacent network elements
7-1 Attenuation table .......................................................................................................................... 7-7
8 WDMX setup and testing: integration procedures
8-1 Channel/port assignments ......................................................................................................... 8-11
8-2 Attenuation Table ....................................................................................................................... 8-11
B Fiber cleaning
B-1 Required and recommended equipment and materials ................................................................B-3
C PTM installation
C-1 Alcatel-Lucent approved PTMs ...................................................................................................C-2
E Backplane pin replacement
E-1 Backplane locations of METRAL™ pins .................................................................................... E-3
E-2 Metral™ pins ............................................................................................................................... E-4

xi
365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
About this document
Purpose
This document provides the information and procedures necessary to install, self-test and
turn up the Alcatel-Lucent 1850 Transport Service Switch 60 (TSS-60) system.
Reason for reissue
This document, Alcatel-Lucent 1850 Transport Service Switch (TSS-60) Installation and
System Turn-up Guide, 365-372-603R2.0, Issue 1, is issued to provide information about
the following circuit packs offered in Release 2.0.
Alcatel-Lucent 1850 TSS-60 Release 2.0 includes support for the following circuit packs:
• LNW801 56DS1E1 circuit pack supports up to 56 DS1/E1 signals with performance
monitoring and is OSP hardened.
• LNW391 DS1/DS3/16/3 circuit pack supports up to 16 DS1 signals with performance
monitoring and up to 3 DS3 signals.
• LNW84 OC3/OC12/OC48 multirate very large fabric (VLF) circuit pack supports up to
eight OC-3/OC-12 or two OC-48 ports with up to 16 DS1 and 3 DS3 ports. The LNW84
circuit pack is OSP hardened.
• LNW402 OC-48 circuit pack supports a single SFP-based low speed DWDM OC-48
signal with a 12 STS-1 VT switch fabric. Existing DWDM pluggable transmission
modules are compatible.
Intended audience
This installation manual is intended to provide individuals and customers the information
and procedures necessary to install, self-test and turn up the Alcatel-Lucent 1850 TSS-60
system.
This manual is not a service or operations manual. Refer to Alcatel-Lucent 1850 Transport
Service Switch (TSS-60), Release 2.0 User Provisioning Guide, 365-372-601R2.0, for any
activities involving circuit turn-up, regular maintenance, or trouble analysis.

............................................................................................................................................................................................................................................................
About this document
xii 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
How to use this document
This manual is divided into the following sections with a brief description of the contents
of each major part/chapter/appendix:
About this document
This chapter describes the purpose, intended audience, reason for reissue, and
organization of this document. This section references related documentation and explains
how to order, make comments or recommend changes to this document.
Chapter 1, “Safety”
This chapter provides laser safety information and precautions.
Part I: “Physical and power installation”
Part I covers Chapters 2, 3, and 4. These sections covers the physical mounting of the
Alcatel-Lucent 1850 TSS-60 shelf using the Horizontal Bay Mount. This section includes
the running and connecting of power cables, interconnecting cables, alarm cables, and as
required, external timing, communication cables, and covers initial circuit pack
installation (not seated). This section also provides the recommended checklist
“Installation checklist” to follow when installing a Alcatel-Lucent 1850 Transport Service
Switch 60 (TSS-60) system. Use of the installation checklist is required to ensure a quality
installation. All completed tasks should be checked off and those not completed should be
duly noted as to the reason why. This checklist should be turned in as part of your job
complete paperwork.
Chapter 2, “Physical installation”
This chapter provides equipment installation instructions for the Alcatel-Lucent 1850
TSS-60 shelf using the horizontal bay mount configuration. The Alcatel-Lucent 1850
TSS-60 shelves with the removable center divider can support either half width or full
width cards in the Main function slots.
Chapter 3, “Cable and fiber installation”
This chapter provides cabling instructions for the Alcatel-Lucent 1850 TSS-60 shelf using
the horizontal bay mount configuration.
Chapter 4, “Circuit pack installation”
This chapter provides information for verifying that the shelf is being supplied with the
proper power and provides instructions for circuit pack installation.

About this document
............................................................................................................................................................................................................................................................
365-372-603R2.0
Issue 1 January 2009 xiii
............................................................................................................................................................................................................................................................
Part II: “Stand-alone installation testing”
Part II covers Chapters 5 and 6. These sections cover the initial Graphical User Interface
(GUI) or Craft Interface Terminal (CIT) software installation and turn-up testing on a new
Alcatel-Lucent 1850 TSS-60 shelf. It is intended to verify correct electrical DS1/DS3/FE
cable wiring to the DSX panel or punch down block as well SONET fiber routing to the
LGX panel from the faceplates of installed packs. This section also the recommended
checklist “Installation checklist” to follow when installing a Alcatel-Lucent 1850
Transport Service Switch 60 (TSS-60) system. Use of the installation checklist is required
to ensure a quality installation. All completed tasks should be checked off and those not
completed should be duly noted as to the reason why. This checklist should be turned in as
part of your job complete paperwork.
Chapter 5, “Stand-alone node setup”
This chapter provides procedures for initial Graphical User Interface (GUI) or Craft
Interface Terminal (CIT) software installation and circuit packs provided via work order.
Also, the use of the Graphical User Interface (GUI) or Craft Interface Terminal (CIT).
Chapter 6, “Stand-alone installation testing”
This chapter is to verify proper transmission cabling installation and Release 2.0
functionality as well as the associated functionality of the Alcatel-Lucent 1850 TSS-60
shelf.
Part III: “Network turn-up and testing”
Part III covers fiber connections between nodes in a ring. It is not intended to replace
acceptance test procedures. This section also provides the recommended checklist
“Installation checklist” to follow when installing a Alcatel-Lucent 1850 TSS-60 system.
Use of the installation checklist is required to ensure a quality installation. All completed
tasks should be checked off and those not completed should be duly noted as to the reason
why. This checklist should be turned in as part of your job complete paperwork.
Chapter 7, “Connecting adjacent network elements”
This chapter is used to make fiber connections between nodes in a ring. It is not intended
to replace acceptance test procedures.
Part IV: “Miscellaneous detailed installation procedure and reference material”
Part IV provides supplementary information that is useful when installing the
Alcatel-Lucent 1850 TSS-60 system and using this Installation Manual.

............................................................................................................................................................................................................................................................
About this document
xiv 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
Appendix A, “Technical support”
This appendix provides important technical assistance information for the Alcatel-Lucent
1850 TSS-60.
Appendix B, “Fiber cleaning”
This appendix describes the Lucent recommended method for the cleaning and inspection
of optical connectors using specific tools and materials that have been proven to be
effective in the assembly and testing of optical transmission equipment.
Appendix D, “Installing fiber connectors and LBOs”
This appendix provides procedures for installing and removing the types of Line Build
Out units (LBOs) and fiber connectors onto input and output ports found on the
Alcatel-Lucent 1850 TSS-60 circuit packs.
Appendix E, “Backplane pin replacement”
This appendix provides information and the procedures used when a pin or blade on the
Alcatel-Lucent 1850 TSS-60 backplane has been bent or broken.
Appendix F, “Fiber labeling”
This appendix describes the labeling of the fiber.
Glossary
The Glossary provides definitions for telecommunication acronyms and terms.
Index
The Index supplies users with specific subjects and corresponding page numbers to find
necessary information.
Safety information
This information product contains hazard statements for your safety. Hazard statements
are given at points where safety consequences to personnel, equipment, and operation may
exist. Failure to follow these statements may result in serious consequences.
Safety precautions
Adhere to the following safety precautions:
•Electrostatic discharge (ESD)
You must be properly grounded when making contact with the Alcatel-Lucent 1850
TSS-60 frame and handling circuit packs, disk drives, and tapes. Wrist strap ground cords
should be routinely tested for the minimum 1-megohm resistance.

About this document
............................................................................................................................................................................................................................................................
365-372-603R2.0
Issue 1 January 2009 xv
............................................................................................................................................................................................................................................................
•Plug-in storage
Circuit packs should be stored in static-safe packaging or in a grounded cabinet.
For additional safety precautions, please see the Alcatel-Lucent 1850 Transport Service
Switch (TSS-60), Release 2.0 User Provisioning Guide, 365-325-601R2.0.
Conventions used
Italic typeface denotes a particular product line or information product.
Arial Bold typeface signifies a window, section, command or parameter used with the TL1
Command Builder. or Graphical User Interface
Helvetica typeface indicates a faceplate or Alcatel-Lucent 1850 TSS-60 label
designation, as in the ACTIVE LED on a circuit pack.
Courier Bold indicates a TL1 command typed in a terminal window by the user, as in
act-user:ALU-TSS-60:ALU01:ctag::1850TSS-60;
Courier typeface indicates the system or PC response to a command.
Related information
Alcatel-Lucent 1850 TSS-60 Documentation Set
The following is a list of related information products:
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 Product
Information and Planning Guide, 365-372-600R2.0
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 User
Provisioning Guide, 365-372-601R2.0
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 Maintenance and
Trouble Clearing Guide ,365-372-602R2.0
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 Installation and
System Turn-Up Guide, 365-372-603R2.0
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 TL1 Command
Guide, 365-372-604R2.0
CAUTION
Laser Safety
When connecting fiber loops between the IN and OUT ports on optical circuit
packs, always connect to the IN port first and then the OUT port. This will
prevent any optical radiation from being present at the fiber end.For more
detailed information and safety precautions, refer to Chapter 1, “Safety”.

............................................................................................................................................................................................................................................................
About this document
xvi 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0.0 Software
Release Description (Paper) — 109693630
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0.0 Software
Release Description (CD-ROM) — 109693648
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0.X Customer
Documentation (CD-ROM) — 109693655
•WaveStar®CIT User Guide — 365-372-330
Alcatel-Lucent 1850 TSS-60 drawings
The following is a list of related drawings:
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 Engineering and
Ordering Information — ED8C959-10
•Alcatel-Lucent 1850 Transport Service Switch (TSS-60), Release 2.0 Interconnect
Information — ED8C959-20
Document support
Alcatel-Lucent provides a referral telephone number for document support. Use this
number to report errors or to ask questions about the document. This is a non-technical
number. The referral number is 1 [phone] (continental United States) or +1 (630)
713-5000 (for all countries).
Technical support
For technical support, contact your local Alcatel-Lucent customer support team. See the
Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support) for contact
information. For more information, refer to Appendix A, “Technical support”.
How to order
To order Alcatel-Lucent documents contact your local sales representative or use Online
Customer Support (OLCS) (http://www.alcatel-lucent.com/support).
How to comment
To comment on this information product, go to the Online Comment Form
(http://www.lucent-info.com/comments) or email your comments to the Comments
Hotline ([e-mail]).

About this document
............................................................................................................................................................................................................................................................
365-372-603R2.0
Issue 1 January 2009 xvii
............................................................................................................................................................................................................................................................
Packaging collection and recovery requirements
Countries, states, localities, or other jurisdictions may require that systems be established
for the return and/or collection of packaging waste from the consumer, or other end user,
or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the
return and/or collection of the packaging waste may be established.
For more information regarding collection and recovery of packaging and packaging
waste within specific jurisdictions, please contact the Alcatel-Lucent Field
Services/Installation - Environmental Health and Safety organization.
Recycling/take-back/disposal of product
Electronic products bearing or referencing the symbol shown below, when put on the
market within the European Union, shall be collected and treated at the end of their useful
life in compliance with applicable European Union and local legislation. They shall not be
disposed of as part of unsorted municipal waste. Due to materials that may be contained in
the product, such as heavy metals or batteries, the environment and human health may be
negatively impacted as a result of inappropriate disposal.
Note: In the European Union, a solid bar under the crossed-out wheeled bin
indicates that the product was put on the market after 13 August 2005.
Moreover, in compliance with legal requirements and contractual agreements, where
applicable, Alcatel-Lucent will offer to provide for the collection and treatment of
Alcatel-Lucent products at the end of their useful life. Alcatel-Lucent will also offer to
provide for the collection and treatment of existing products displaced by Alcatel-Lucent
equipment.
For information regarding take-back of equipment by Alcatel-Lucent, or for more
information regarding the requirements for recycling/disposal of product, please contact
your Alcatel-Lucent Account Manager or Alcatel-Lucent Take-Back Support at
[e-mail].

............................................................................................................................................................................................................................................................
About this document
xviii 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................

1-1
365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
1Safety
Overview
Purpose
This chapter provides important safety instructions for the Alcatel-Lucent 1850 Transport
Service Switch 60 (TSS-60).
Contents
This appendix provides information on the following topics:
Laser safety 1-2
Electrostatic discharge ESD considerations 1-5
Laser product classification 1-10
Alcatel-Lucent 1850 TSS-60 optical specifications 1-12

............................................................................................................................................................................................................................................................
Laser safetySafety
1-2 365-372-603R2.0
Issue 1 January 2009
............................................................................................................................................................................................................................................................
Laser safety
System design
The Alcatel-Lucent system complies with FDA/CDRH 21 CFR 1040.10 and 1040.11 as a
Class I and with IEC 60825-1 as a Class 1 Optical Fiber Telecommunication laser product.
The system has been designed to ensure that the operating personnel is not endangered by
laser radiation during normal system operation. The safety measures specified in the Food
and Drug Administration’s Center for Devices and Radiological Health (FDA/CDRH)
regulations and the international standards IEC-60825 or DIN/EN 60825 are met. Please
also refer to “Laser product classification” (p. 1-10).
Potential sources of danger
Beware of the following potential sources of danger which will remain despite all safety
measures taken:
•Laser radiation can cause damage to the skin and eyes.
•Laser radiation from optical transmission systems is in a wavelength range that is
invisible to the human eye.